• Macromolecular Research
• /
• v.16 no.3
• /
• pp.247-252
• /
• 2008

Lithium gel electrolytes based on a mixed polymer matrix consisting of poly(vinylidenefluoride-hexafluoropropylene) (PVDF-HFP) and cyanoresin type M (CRM) were prepared using an in situ blending process. The CRM used in this study was a copolymer of cyanoethyl pullulan and cyanoethyl poly(vinyl alcohol) (PVA) with a mole ratio of 1:1. The mixed plasticizer was ethylene carbonate (EC) and propylene carbonate (PC) with a volume ratio of 1:1. In this study, the presence of PVDF in the electrolytes helps to form a dimensionally stable film over a broad composition range, and decreases the viscosity. In addition, it provides better rheological properties that are suitable for the extrusion of thin films. However, the presence of HFP has a positive effect on generating an amorphous domain in a crystalline PVDF structure. The ionic conductivity of the polymer electrolytes was investigated in the range 298-333 K. The introduction of CRM into the PVDF-HFP/$LiPF_6$, complex produced a PVDF-HFP/CRM/$LiPF_6$ complex with a higher ionic conductivity and improved thermal stability and dynamic mechanical properties than a simple PVDF-HFP/$LiPF_6$, complex.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.3
• /
• pp.1-7
• /
• 2017

Multi-wafer planetary type chemical vapor deposition reactors are widely used in thin film growth and suitable for large scale production because of the high degree of growth rate uniformity and process reproducibility. In this study, a two-dimensional model for estimating the effect of the gap between satellite and wafer on the wafer surface temperature distribution is developed and analyzed using computational fluid dynamics technique. The simulation results are compared with the results obtained from an analytical method. The simulation results show that a drop in the temperature is noticed in the center of the wafer, the temperature difference between the center and wafer edges is about $5{\sim}7^{\circ}C$ for all different ranges of the gap, and the temperature of the wafer surface decreases when the size of the gap increases. The simulation results show a good agreement with the analytical ones which is based on one-dimensional heat conduction model.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.4
• /
• pp.348-352
• /
• 2022

Resistive switching behaviors of a co-sputtered zinc silicate thin film (ZnO and SiO₂ targets) have been investigated. We fabricated an Ag/ZnSiO_x/highly doped n-type Si substrate device by using an RF magnetron sputter system. X-ray diffraction pattern (XRD) indicated that the Zn₂SiO₄ was formed by a post annealing process. A unique morphology was observed by scanning electron microscope (SEM) and atomic force microscope (AFM). As a result of annealing process, 50 nm sized nano clusters were formed spontaneously in 200~300 nm sized grains. The device showed a unipolar resistive switching process. The average value of the ratio of the resistance change between the high resistance state (HRS) and the low resistance state (LRS) was about 106 when the readout voltage (0.5 V) was achieved. Resistance ratio is not degraded during 50 switching cycles. The conduction mechanisms were explained by using Ohmic conduction for the LRS and Schottky emission for the HRS.

• Current Optics and Photonics
• /
• v.7 no.3
• /
• pp.254-262
• /
• 2023

Novel thermo-optically focus-switchable Fresnel zone plates based on phase-change metafilms are designed and analyzed at a visible wavelength (660 nm). By virtue of the large thermo-optic response of vanadium dioxide (VO₂) thin film, a phase-change material, four different plasmonic phase-change absorbers are numerically designed as actively tunable Gires-Tournois Al-VO₂ metafilms in two and three dimensions. The designed phase-change metafilm unit cells are used as the building blocks of actively focus-switchable Fresnel zone plates with strong focus switching contrast (40%, 83%) and high numerical apertures (1.52, 1.70). The Fresnel zone plates designed in two and three dimensions work as cylindrical and spherical lenses in reflection type, respectively. The coupling between the thermo-optic effect of VO₂ and localized plasmonic resonances in the Al nanostructures offer a large degree of freedom in design and high-contrast focus-switching performance based on largely tunable absorption resonances. The proposed method may have great potential in photothermal and electrothermal active optical devices for nonlinear optics, microscopy, 3D scanning, optical trapping, and holographic displays over a wide spectral range including the visible and infrared regimes.

• Korean Journal of Materials Research
• /
• v.7 no.2
• /
• pp.102-106
• /
• 1997

Micro gas sensors including thin film catal) tic type require stress-free memhrancs for etch stop of Si anisotropic etching and sublayer of sensing elements hecause stress is one of the main factors affecting breakdown of thin membranes. This paper reports the effects of deposition conditions on stress and refractive index of $SiN_{x}/SiO_{x}/(NON)$ films deposited by low pressure c11ernic;rl vapor deposition(L, t'CVI)) 2nd reactve sputtering. In the case of I.PCVI1, the stresses of $SiN_{x}$ and NON films arc $7.6{\times}10^{8}dyne/cm^2$ and $3.3{\times}10^{8}dyne/cm^2$, respectibely, and the refractive indices are 3.05 and 152, respectively. In the cxse oi the sputtered SiN, , compressi\e stress decreased in magnitude and then turned to tensility as increasing proc, ess pressure by lmtorr to 30mtorr and cicreasmg applied power density by $2.74W/cm^2$ to $1.10W/cm^2$. The hest value of film stress obt;~ined under condition of lOmtorr and $1.37W/cm^2$ in this' experiment was $1.2{\times}10^{9}dyne/cm^2$ cnnipressive. The refr~ict~ve index decreased from 2 05 to 1 89 as decreasing applied power density by lnitorr to 3Orntorr and increasing process pressure hy $2.74W/cm^2$ to $1.10W/cm^2$. Stresses of films deposited by both LPCVL) and sputtering decreased as incre;lsing temperature and showed plastic behavior as decreasing temperature.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.311-311
• /
• 2016

최근 고성능 디스플레이 개발이 요구되면서 기존 비정질 실리콘(a-Si)을 대체할 산화물 반도체에 대한 연구 관심이 급증하고 있다. 여러 종류의 산화물 반도체 중 a-IGZO (amorphous indium-gallium-zinc oxide)가 높은 전계효과 이동도, 저온 공정, 넓은 밴드갭으로 인한 투명성 등의 장점을 가지며 가장 연구가 활발하게 보고되고 있다. 기존에는 SG(단일 게이트) TFT가 주로 제작 되었지만 본 연구에서는 DG(이중 게이트) 구조를 적용하여 고성능의 a-IGZO 기반 박막 트랜지스터(TFT)를 구현하였다. SG mode에서는 하나의 게이트가 채널 전체 영역을 제어하지만, double gate mode에서는 상, 하부 두 개의 게이트가 동시에 채널 영역을 제어하기 때문에 채널층의 형성이 빠르게 이루어지고, 이는 TFT 스위칭 속도를 향상시킨다. 또한, 상호 모듈레이션 효과로 인해 S.S(subthreshold swing)값이 낮아질 뿐만 아니라, 상(TG), 하부 게이트(BG) 절연막의 계면 산란 현상이 줄어들기 때문에 이동도가 향상되고 누설전류 감소 및 안정성이 향상되는 효과를 얻을 수 있다. Dual gate mode로 동작을 시키면, TG(BG)에는 일정한 positive(or negative)전압을 인가하면서 BG(TG)에 전압을 가해주게 된다. 이 때, 소자의 채널층은 depletion(or enhancement) mode로 동작하여 다른 전기적인 특성에는 영향을 미치지 않으면서 문턱 전압을 쉽게 조절 할 수 있는 장점도 있다. 제작된 소자는 p-type bulk silicon 위에 thermal SiO2 산화막이 100 nm 형성된 기판을 사용하였다. 표준 RCA 클리닝을 진행한 후 BG 형성을 위해 150 nm 두께의 ITO를 증착하고, BG 절연막으로 두께의 SiO2를 300 nm 증착하였다. 이 후, 채널층 형성을 위하여 50 nm 두께의 a-IGZO를 증착하였고, 소스/드레인(S/D) 전극은 BG와 동일한 조건으로 ITO 100 nm를 증착하였다. TG 절연막은 BG 절연막과 동일한 조건에서 SiO2를 50 nm 증착하였다. TG는 S/D 증착 조건과 동일한 조건에서, 150 nm 두께로 증착 하였다. 전극 물질과, 절연막 물질은 모두 RF magnetron sputter를 이용하여 증착되었고, 또한 모든 patterning 과정은 표준 photolithography, wet etching, lift-off 공정을 통하여 이루어졌다. 후속 열처리 공정으로 퍼니스에서 질소 가스 분위기, $300^{\circ}C$ 온도에서 30 분 동안 진행하였다. 결과적으로 $9.06cm2/V{\cdot}s$, 255.7 mV/dec, $1.8{\times}106$의 전계효과 이동도, S.S, on-off ratio값을 갖는 SG와 비교하여 double gate mode에서는 $51.3cm2/V{\cdot}s$, 110.7 mV/dec, $3.2{\times}108$의 값을 나타내며 훌륭한 전기적 특성을 보였고, dual gate mode에서는 약 5.22의 coupling ratio를 나타내었다. 따라서 산화물 반도체 a-IGZO TFT의 이중게이트 구조는 우수한 전기적 특성을 나타내며 차세대 디스플레이 시장에서 훌륭한 역할을 할 것으로 기대된다.

• Journal of the Korean Vacuum Society
• /
• v.21 no.1
• /
• pp.12-16
• /
• 2012

Although silver is used for T-OLED (Top emitting organic Light-Emitting Diode) as reflective anode, it is not an ideal material due to its low work function. Thus, we study the effect of annealing and atmospheric pressure plasma treatment on Ag film that increases its work function by forming the thin silver oxide layer on its surface. In this study, we deposited silver on glass substrate using RF sputtering. Then we treated the Ag samples annealing at $300^{\circ}C$ for 30 minutes in atmosphere or treating the atmospheric plasma treatment for 30, 60, 90, 120s, respectively. We measured the change of the mechanical properties and the potential value of surface with each one at a different treatment type and time. We used nano-indenter system and KPFM (Kelvin Probe Force Microscopy). KPFM method can be measured the change of surface potential. The nanoindenter results showed that the plasma treatment samples for 30s, 120s had very low elastic modulus, hardness and Weibull modulus. However, annealed sample and plasma treated samples for 60s and 90s had better mechanical properties. Therefore, plasma treatment increases the uniformity thin film and the surface potential that is very effective for the performace of T-OLED.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.348-348
• /
• 2014

차세대 디스플레이 구동 회로 소자를 위한 재료로서, Amorphous Oxide Semiconductor (AOS)가 주목받고 있다. AOS는 기존의 Amorphous Silicon과 비교하여 뛰어난 이동도를 가지고 있으며, 넓은 밴드 갭에 의한 투명한 광학적 특성을 가지고 있다. 이러한 장점을 이용하여, AOS 박막은 thin film transistor (TFT)의 active channel로 이용 되고 있다. 하지만, AOS를 이용한 TFT의 경우, 시간이 경과함에 따라 $O_2$ 및 $H_2O$ 흡착에 의해 전기적 특성이 변하는 현상이 있다. 이러한 현상은 소자의 신뢰성에 있어 중요한 문제가 된다. 이러한 문제를 연구하기 위해 본 논문에서는, AOS 박막을 이용하여 bottom 게이트형 TFT를 제작하였다. 이를 위해 먼저, p-type Si 위에 건식산화방식으로 $SiO_2$(100 nm)를 성장시켜 게이트 산화막으로 이용하였다. 그리고 Zn과 Sn이 1: 2의 조성비를 가진 ZnSnO (ZTO) 용액을 제조한 후, 게이트 산화막 위에 spin coating 하였다. Splin coating된 용액에 남아 있는 솔벤트를 제거하기 위해 10분 동안 $230^{\circ}C$로 열처리를 한 후, 포토리소그래피와 에칭 공정을 이용하여 ZTO active channel을 형성하였다. 그 후, 박막 내에 남아 있는 불순물을 제거하고 ZTO TFT의 전기적인 특성을 향상시키기 위하여, $600^{\circ}C$의 열처리를 30분 동안 진행 하여 junctionless형 TFT 제작을 완료 하였다. 제작된 소자의 시간 경과에 따른 열화를 확인하기 위하여, 대기 중에서 2시간마다 HP-4156B 장비를 이용하여 전기적인 특성을 확인 하였으며, 이러한 열화는 후처리 공정을 통하여 회복시킬 수 있었다. 열화의 회복을 위한 후처리 공정으로, 퍼니스를 이용한 고온에서의 열처리와 microwave를 이용하여 저온 처리를 이용하였다. 결과적으로, TFT는 소자가 제작된 이후, 시간에 경과함에 따라서 on/off ratio가 감소하여 열화되는 경향을 보여 주었다. 이러한 현상은, TFT 소자의 ZTO back-channel에 대기 중에 있는 $O_2$ 및 $H_2O$의 분자의 물리적인 흡착으로 인한 것으로 보인다. 그리고 추가적인 후처리 공정들에 통해서, 다시 on/off ratio가 회복 되는 현상을 확인 하였다. 이러한 추가적인 후처리 공정은, 열화된 소자에 퍼니스에 의한 고온에서의 장시간 열처리, microwave를 이용한 저온에서 장시간 열처리, 그리고 microwave를 이용한 저온에서의 단 시간 처리를 수행 하였으며, 모든 소자에서 성공적으로 열화 되었던 전기적 특성이 회복됨을 확인 할 수 있었다. 이러한 결과는, 저온임에도 불구하고, microwave를 이용함으로 인하여, 물리적으로 흡착된 $O_2$ 및 $H_2O$가 짧은 시간 안에 ZTO TFT의 back-channel로부터 탈착이 가능함과 동시에 소자의 특성을 회복 가능 함 의미한다.

• Journal of the Korean Vacuum Society
• /
• v.17 no.5
• /
• pp.435-441
• /
• 2008

In this paper, we investigated the electrical properties of triisopropylsilyl (TIPS) pentacene organic thin-film transistor (OTFT) depending on solvent type. We spin coated TIPS pentacene by using chlorobenzene, p-xylene, chloroform, and toluene as solvents. Fabricated OTFT with chlorobenzene shows field-effect mobility of $1.0{\times}10^{-2}cm^2/V{\cdot}s$, on/off ratio of $4.3{\times}10^3$ and threshold voltage of 5.5 V. In contrast, with chloroform, the mobility is $5.8{\times}10^{-7}cm^2/V{\cdot}s$, on/off ratio of $1.1{\times}10^2$ and threshold voltage of 1.7 V. Moreover we measured the grain size of each TIPS pentacene solvent by atomic force microscopy (AFM). From these results, it can be concluded that a solvent with higher boiling point results in better electrical characteristics due to large grain size and high crystallinity of TIPS pentacene layer. In this paper TIPS pentacene with chlorobenzene shows the best electrical properties.

• Korean Journal of Materials Research
• /
• v.21 no.10
• /
• pp.573-579
• /
• 2011

Highly textured Ag, Al and Al:Si back reflectors for flexible n-i-p silicon thin-film solar cells were prepared on 100-${\mu}m$-thick stainless steel substrates by DC magnetron sputtering and the influence of their surface textures on the light-scattering properties were investigated. The surface texture of the metal back reflectors was influenced by the increased grain size and by the bimodal distribution that arose due to the abnormal grain growth at elevated deposition temperatures. This can be explained by the structure zone model (SZM). With an increase in the deposition temperatures from room temperature to $500^{\circ}C$, the surface roughness of the Al:Si films increased from 11 nm to 95 nm, whereas that of the pure Ag films increased from 6 nm to 47 nm at the same deposition temperature. Although Al:Si back reflectors with larger surface feature dimensions than pure Ag can be fabricated at lower deposition temperatures due to the lower melting point and the Si impurity drag effect, they show poor total and diffuse reflectance, resulting from the low reflectivity and reflection loss on the textured surface. For a further improvement of the light-trapping efficiency in solar cells, a new type of back reflector consisting of Ag/Al:Si bilayer is suggested. The surface morphology and reflectance of this reflector are closely dependent on the Al:Si bottom layer and the Ag top layer. The relationship between the surface topography and the light-scattering properties of the bilayer back reflectors is also reported in this paper.