• Journal of the Korean Wood Science and Technology
• /
• 제34권5호
• /
• pp.52-58
• /
• 2006

Coffee chaff for manufacturing of the 6 mm thick cement-bonded boards was obtained from a coffee processing industry at Omuo-Ekiti, in Ekiti State, Nigeria. Boards were produced with three levels of cement to coffee chaff ratio of 1.5:1, 2.5:1 and 3.5:1; and at three levels of mixing curing reagent of 2.0%, 2.5% and 3.0%. Three dimensional properties of thickness swelling (TS), water absorption (WA) and linear expansion (LE) were investigated after 48 hours immersion in water. The mean values obtained for TS, WA and LE ranged from 0.46% to 1.47%, from 11.52% to 24.00%, from 0.19% to 0.35%, respectively. The most dimensionally stable boards were produced at the highest mixing levels of curing reagent and cement to coffee chaff ratio of 3.0% and 3.5:1, respectively. The coffee chaff is suitable as raw material for the manufacture of cement-bonded composites and it would be able to stimulate and activate the use of other agro-byproducts for the manufacture of value-added panels.

• Journal of the Korean Wood Science and Technology
• /
• 제48권6호
• /
• pp.907-916
• /
• 2020

This research was conducted to investigate the linear expansion and resistance properties of a composite board (com-ply). This board was made of medium-density fiberboard (MDF) laminated using avocado (Persea americana), mahogany (Swietenia mahogani), and pine (Pinus merkusii) veneers. These three types of veneers were laminated on both surfaces of the MDF using adhesives, namely, epoxy and isocyanate. Glue (250 g·m^-2) was spread on the surface, followed by cold press for 3 h with an applied pressure of 15 kg·cm^-2. The research result revealed that com-ply exhibited an increased dimensional stability compared with MDF, indicated by reduction in water absorption, thickness swelling, and linear expansion. The com-ply made of the pine veneer and isocyanate adhesive exhibited high density, water absorption, thickness swelling, and screw withdrawal load. The com-ply that exhibited the strongest resistance to drywood termite attacks was the one made of the mahogany veneer and isocyanate adhesive. Moreover, the com-ply that exhibited the biggest weight loss (3.6 %) was made of the pine veneer and epoxy adhesive. The results of this research may facilitate in manufacturing com-ply using the selected veneer and adhesive without the application of hot press.

• Journal of the Korean Wood Science and Technology
• /
• 제29권2호
• /
• pp.109-117
• /
• 2001

한지(韓紙) 제조(製造) 공정(工程) 중에서 발생하는 백색 슬러지와 흑색 슬러지를 각각 일정비율(10, 20, 30, 40%)로 목재(木材) 파티클과 혼합(混合)하고 PMDI, 요소 및 페놀수지를 이용하여 각각 목표비중(目標比重) 0.60, 0.75, 0.90 별로 복합(複合)보드를 제조(製造)하여 물리적(物理的) 성질(性質)을 측정 분석한 결과 흡수길이변화율은 대조보드에 비해 크게 증가하지 않았으며 흡수두께팽창율은 PMDI를 적용한 백색 슬러지 목재(木材) 파티클 복합(複合)보드가 가장 낮은 값을 보였고 흡수율은 흑색 슬러지 목재(木材) 파티클 복합(複合)보드의 경우 혼합(混合) 비율(比率)이 증가할수록 대체로 감소하는 경향을 보였다.

• Journal of the Korean Wood Science and Technology
• /
• 제47권2호
• /
• pp.239-248
• /
• 2019

This research presents an improvement of the physical and mechanical properties of composite board (com-ply) made of Oriented Strand Board (OSB) coated with wood veneer of Pine (Pinus merkusii), Avocado (Persea Americana) and Mahogany (Swietenia mahogany). 1.5 mm thick veneers of those three wood types were adhered to the surface of OSB using two adhesive types: epoxy and isocyanate. The adhesive with the glue spread of $250g\;m^{-2}$ applied using single glue line was spread and then cold pressed with the pressure of $15kg\;cm^{-2}$ for 3 hours. The research result showed an improving dimension stability of com-ply, but not found on all parameters of physical property test. The moisture content seemed to be influenced by the com-ply type, yet not related to its thickness swelling, water absorption and linear expansion. The exception took place in the parallel linear expansion when immersed for 2 hours. The highest to the lowest increases of MOE and MOR were consecutively found on OSB coated with wood veneer of Pine, Mahogany and Avocado. However, the increases were statistically insignificant. The highest increasing screw hold power was found at the com-ply type AE (avocado veneer and epoxy adhesive) that was by 28%.

• 한국산림과학회지
• /
• 제63권1호
• /
• pp.12-20
• /
• 1984

본(本) 연구(硏究)는 국산낙엽송재(國産落葉松材)를 이용(利用)한 압체온도(壓締温度)와 시간(時間)에 따른 파티클보오드의 특성(特性)들을 조사(調査)하였다. 결론(結論)을 요약(要約)하면 다음과 같다. 1) 길이와 두께의 비율(比率)이 1:1~35인 비교적(比較的) 불리(不利)한 조건하(條件下)의 chip임에도 불구하고 chip의 표면(表面)이 비교적(比較的) 매끈하게 접착제(接着劑)의 도포(塗布)가 고르게 되고, 공시재(供試材)의 좋은 접착특성(接着特性)이 물리적(物理的) 성질(性質)에 좋은 영향(影響)을 주었다. 2) MOR, MOE, SHA에서 압체시간(壓締時間)이 10분(分)일 때 더욱 좋은 기계적(機械的) 특성(特性)을 보여주고 있다. 3) MOR, IBS, SHA에서 압체시간(壓締時間)이 20분(分)인 경우에 온도(温度)에 따른 그 유의성(有意性)이 인정(認定)되지 않았다. 이는 공시재(供試材)의 노화작용(老化作用)과 수지(樹脂)의 연화작용(軟化作用)이 상호작용(相互作用)하여 일어나는 현상(現狀)으로 보인다. 4) 박리저항(剝離抵抗)에서 압체시간(壓締時間)이 10분(分)일 때 온도(温度)에 따른 내부저항(內部低抗) 값이 증가(增加)되고 있는 것은 중층(中層)에 수지(樹脂)의 적정(適定) 경화온도(硬化温度)가 형성(形成)되는 시간(時間) 때문이다. 5) 흡수(吸水) 팽창(膨脹)에서 압체온도(壓締温度)와 압체시간(壓締時間)에 큰 영향(影響)을 주는데, 이는 열처리(熱處理) 효과(效果)에 따른 공시재(供試材)의 흡수성(吸水性), 이방성(異方性), 불균일성(不均一性) 등(等)이 감소(減)少되어 치수 안전성(安定性)을 유지(維持)시키는데 큰 역할(役割)을 하기 때문이다. 따라서 압체시간(壓締時間)과 압체온도(壓締温度)가 증가(增加)할수록 보다 좋은 치수 안전성(安定性)을 보여 준다.

• Journal of the Korean Wood Science and Technology
• /
• 제24권1호
• /
• pp.17-26
• /
• 1996

This research was accomplished to evaluate possibility of using paper sludge for the raw materials of wood based panel products. The experimental panels were manufactured by four mixed ratios, the proportion of paper sludge to wood particle: 20:80, 30:70, 40:60, 50:50% (oven dry weight basis) and by three composition types, sludge-particle mixed board, three layered sludge-particle board and three layered particle board. They were tested mechanical (bending strength and internal bond) and physical properties (water absorption, thickness swelling and linear expansion). From the results they were shown that bending strength of mixed and three layered sludge-particle board were decreased with increasing of composition ratios of sludge. And the mechanical and physical properties of the boards of three layered composition types have superior to those of mixed composition type. Although composition ratios of sludge increased, the internal bond strength and dimensional stability of sludge-particle board not decreased quantitatively. We concluded that the mechanical and physical properties of three layered sludge-particle board were similar w those of three layered particle-board (control) made by our laboratory design. Therefore, it was recognized that paper sludge can be used as potential raw material in particle-board manufacturing industry.

• Journal of the Korean Wood Science and Technology
• /
• 제18권2호
• /
• pp.67-78
• /
• 1990

This study was performed to determine the characteristics of physical and mechanical properties of domestic wood based materials; plywood, particleboard, medium density fiberboard. Main items of tested properties were panel size, moisture content, water absorption, linear expansion and thickness swelling, glue bond shear strength, bending properties(stress at proportional limit, modulus of rupture. modulus of elasticity), tensile strength, screw holding strength, and internal bond as neccessary. the results were discussed mainly with Korean Standards. The obtained conclusions are as follows; 1. Length and width of 3mm thin plywood(3-ply) and 12mm thick plywood(7-ply) were satished with KS-standard, but thicknesses of these panels were not- passed tolerance limit except one of eight makers. 2. Length and width of particleboard and medium density fiberboard were greater than the tolerance limit value of KS standard, but the thicknesses of these panels were passed this value. 3. Moisture contents of 12mm thick and 3mm thin plywood were satisfied with KS-standard except one mill made 3mm thin plywood. 4. Moisture absortion of plywood was not passed tolerance limit of KS-standard but particleboard was satisfied with this standard value. 5. Dry and wet shear strengths in glue bond of 3mm thin plywood were not reached to KS-standard, but those of 12mm thick plywood were sufficiently satisfied with KS standrad. 6. Modulus of ruptures, parallel to grain and perpendicular to grain of plywood, and particleboard and medium density fiberboard were satisfied with KS-standard. 7. Tensile strengths, parallel to grain and perpendicular to grain of plywood were satisfied with allowance stress of US product standard PS 1-74. 8. Screw holding strength of particleboard was not reached to KS standard, but internal bond was satisfied with KS standard.

• Journal of the Korean Wood Science and Technology
• /
• 제23권2호
• /
• pp.55-69
• /
• 1995

The primary objective of this research was to investigate optimum manufacturing condition of thin composite panels composed of sawdust, polyethylene film and polypropylene net. At the study the experiment was designed to make thin board in which sawdust offers effectiveness as core composing material, polyethylene as adhesive with added urea resin, and polypropylene as stiffness and flexibility in the composition panel. 100 types of thin composite panels were manufactured according to press-lam and mat-forming process of various hot pressing conditions(pressure, temperature and time). They were tested and compared with control boards on bending properties(MOR, MOE, SPL, WML), internal bond strength, thickness swelling, linear expansion and water absorption. At the same time the visual inspections of each types of panels were accomplished. The physical and mechanical properties of composite types passed by visual inspection were analyzed by Tukey's studentized range test. From the statistical analysis, the optimum manufacturing condition of thin composite panels were selected. Compared with two manufacturing processes, mat-forming process performed better than press-lam process in all tested properties. The optimum manufacturing conditions resulted from the experiment and statistical analysis were able to determine as following: the press temperature was shown the most good result at 130$^{\circ}C$ in mat forming process and 140$^{\circ}C$ press lam process, the press time 4 min in both processes, but the press pressure was 25-10kg/$cm^2$ in mat forming and 15k/$cm^2$ press lam process.

• Journal of the Korean Wood Science and Technology
• /
• 제22권4호
• /
• pp.19-25
• /
• 1994

이 연구는 저급합판이나 파아티클보오드의 표면단판 대용으로 얇은 하아드 보오드가 사용될 수 있는지의 여부를 측정하는데 그 목적이 있다. 이 하아드보오드의 제조를 위하여 사용되는 공시재료는 여러 형태의 폐지류를 여러 혼합조건으로, 접착제로서 합성수지와 함께 또는 합성수지를 첨가하지 않은 상태에서, 실험실적 장치로 하아드보오드를 제조하였다. 이들 폐지류는 상당의 리그닌을 함유한 폐골판지, 우유 및 씨리얼 포장지, 그리고 폐잡지를 포함하였다. 실험결과는 0.32cm 두께의 상업용 하아드보오드에 필적할 수 있는 0.21~0.16cm 두께의 하아드보오드를 이들 폐지류로부터 얻을 수 있었다. 이들 폐지류의 혼합효과는 영계수(MOE)와 Taber-마모성 실험을 비롯한 하아드보오드의 제 물리적 성질 즉 두께 팽윤율, 수분 흡수율 및 길이 팽창율에 현저히 나타남을 확인하였다. 이들 폐지류의 혼합과 사용한 합성수지는 하아드보오드의 비중, 영계수(MOE)와 제 물리적 성질에 민감하게 영향을 미쳤다. 이 하아드보오드의 이러한 제 물리적 성질은 저급합판이나 파아티클보오드의 표면단판 내용으로 사용할 수 있음을 보여 주었다.