• KCI Concrete Journal
• /
• 제11권3호
• /
• pp.45-52
• /
• 1999

A Computer-based iterative method is provided for the calculation of minimum thickness values for one-way slabs to satisfy the maximum permissible limits given in the ACI Building Code. An algorithm includes the effects of cracking and time-dependent effects due to creep and shrinkage. Comparison of the calculated minimum thickness values with the current ACI limits is conducted to investigate limitations of the current tabulated minimum thickness. which are constant to a range of design conditions.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권2호
• /
• pp.1288-1291
• /
• 2007

We investigated the effect of Cr thickness on the electrical properties of triisopropylsilyl pentacene organic thin-film transistor (OTFT) employing suspended source-drain electrode. With Cr thickness of 10 nm, the field-effect mobility, on/off ratio and subthreshold slope were $0.017\;cm^2/Vs$, $8.78\;{\times}\;10^3$ and 10 V/decade, respectively. By increasing the Cr thickness to 100 nm, the fieldeffect mobility was increased to $0.032\;cm^2/Vs$, on/off ratio to $1.12{\times}10^5$ and subthreshold slope to 1 V/decade.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.648-651
• /
• 2001

We studied about luminance characteristics of blue organic electroluminecent device as thickness ratio. The device is fabricated TPD(N,N'-dyphenyl-N-N'-bis(3-methyphenyl) -1,1'-biphenyl-4,4'-diamine) as hole transport layer and Butyl -PBD(1,1,4,4-Tetraphenyl-1,3-butadiene) as emission layer and electron transport layer. Total thickness is 1000${\AA}$ as HTL and ETL, each devices has 500${\AA}$:500${\AA}$. 400${\AA}$:600${\AA}$ and 600${\AA}$:400${\AA}$ of TPD : Butyl-PBD. We obtained the maximum brightness about 175cd/㎡ 500${\AA}$: 500${\AA}$ thickness devices as HTL:ETL

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2009년도 춘계학술대회 논문집
• /
• pp.403-407
• /
• 2009

It is reported that the heavy weight floor impact noise of a slab system is very sensitive to the location of microphone and impact load. In addition, it is known that the aspect raio, thickness and boundary condition of a slab also have great effect on the noise induced by impact load. However, the effect has been mainly evaluated by experimental test and numerical analysis is nearly performed to verify the effect quantitatively. In this study, the effect of the aspect ratio, thickness and boundary condition on the heavy weight floor impact noise is examined through numerical analysis for simple rectangular slab system. The results show that the thickness and boundary condition have a strong correlation with the noise of the slab, on the contrary, the aspect ratio has little relation with the noise.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2007년도 추계 학술대회논문집
• /
• pp.39-44
• /
• 2007

A similarity solution of the Navier-Stokes equation for the axisymmetric stagnation flow near a plane wall coated with a magnetic fluid of uniform thickness is constructed. The shape functions representing the flow in two (magnetic and normal) fluid layer are determined from a third order boundary value problem, which is solved by the Runge-Kutta method with two shooting parameters. Features of the flow including streamline pattern and interface velocity are investigated for the varying values of density ratio, viscosity ratio, and Reynolds number. The results for the interface and wall shear stress, boundary layer and displacement thickness are also presented.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1997년도 제26회 추계학술대회
• /
• pp.200-210
• /
• 1997

This paper presents the thermal behaviours of a solid type disk brake for a high-speed train. The thermal behaviours of a brake disk with 50mm thickness shows good performance compared with 45mm thickness of a disk because of a high specific heat capacity and thermal expansion ratio. The FEM results show that the thickness of the d!sk with a same weight of the brake disk should be increased for a good flexibility of the contact thermal problems. Therefore, the ratio between the pad and disk in diameter may be reduced and the thickness of a disk increased.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.84-86
• /
• 2007

Aluminum sheets were asymmetrically cold rolled without lubrication by using different roll velocities of upper and lower rolls in order to intensify the shear deformation. During asymmetrical cold rolling of aluminum sheets, a reduction per a rolling pass, initial sheet thickness, roll diameter, roll velocity ratio were varied to investigate the effect of rolling parameters. The formation of through thickness shear texture was related to the ratio of the contact length between the roll and sample($l_c$) to the sheet thickness(d). The strain states associated with asymmetrical rolling were investigated by the finite element method (FEM) simulation. FEM results indicated that the evolution of deformation texture in a thickness layer is strongly governed by integrated values of strain rates $\dot{\varepsilon}_{13}$ and $\dot{\varepsilon}_{11}$ along the streamline in the roll gap.

• 한국전산유체공학회지
• /
• 제12권4호
• /
• pp.20-27
• /
• 2007

Two-dimensional stagnation flow toward a plane wall coated with magnetic fluid of uniform thickness is investigated. The flow field is represented as a similarity solution of the Navier-Stokes equation for this incompressible laminar flow. The resulting third order ordinary differential equation is solved numerically by using the shooting method and by determining two shooting parameters so as to satisfy the boundary and interface conditions. Features of the flow including streamline patterns are investigated for the varying values of density ratio, viscosity ratio, and Reynolds number. An adverse flow with double eddy pair in magnetic fluid region is found to emerge as the Reynolds number becomes higher than a threshold value. The results for the interface velocity, interface and wall shear stress, and boundary layer and displacement thickness are also presented.

• 한국환경복원기술학회지
• /
• 제13권4호
• /
• pp.10-17
• /
• 2010

The objectives of this study were to compare the growth of Vitex rotundifolia as affected by the difference of soil depth and mixture ratio in a shallow-extensive green roof module system, and to identify the level of soil thickness and mixture ratio as suitable growing condition to achieve the desired plant growth in green roof. Different soil thickness levels were achieved under 7cm, 15cm and 25cm of shallow-extensive green roof module systems made by woody frame of $500{\times}500{\times}300mm$. Soil mixture ratio were eight types for perlite : peatmoss : leafmold = 7 : 1 : 2 (v/v/v, $P_7P_1L_2$), perlite : peatmoss : leafmold = 6 : 2 : 2 (v/v/v, $P_6P_2L_2$), perlite : peatmoss : leafmold = 5 : 3 : 2 (v/v/v, $P_5P_3L_2$), perlite : peatmoss : leafmold = 4 : 4 : 2 (v/v/v, $P_4P_4L_2$), only sand ($S_{10}$), sand : leafmold = 7 : 3 (v/v, $S_7L_3$), sand : leafmold = 5 : 5 (v/v, $S_5L_5$) and only leafmold ($L_{10}$). The growth response of Vitex rotundifolia had fine and sustain condition in $P_6P_2L_2$, $P_5P_3L_2$ and $P_4P_4L_2$., Especially, in case of $P_6P_2L_2$, growth response appeared to be good even in soil thickness 7cm, which showed low survival rates of Vitex rotundifolia in other soil mixtures. Tree height, root diameter, photosynthesis and chlorophyll contents tended to increase with increased soil thickness.

• 한국진공학회지
• /
• 제5권3호
• /
• pp.258-262
• /
• 1996

d.c.magnetron sputtering 방법으로 제작된 Fe/[NiFe/Cu] 다층박막을 Fe 기저층의 두께, 적층횟수 및 열처리 온도 변화에 따라 자기저항비가 계면 거칠기 및 우선 배향에 미치는 영향에 대하여 조사하였다. Fe 기저층의 두께가 증가함에 따라 (200) 우선 배향의 세기라 증가하였으며, 자기저항비는 Fe70$\AA$의 두께어서 최대값 4.7%를 보이며 이때 자장감응도도 최대를 나타낸다. Fe 기저층의 두께를 70$\AA$ 으로 고정시키고 적층횟수를 변화시켰을 때 40층에서 최대값 5.3%를 보였다. 열처리 온도에 따른 자기저항비는 $300^{\circ}C$이하에서는 커다란 변화가 없으며, $300^{\circ}C$이상에서는 크게 감소하였는데, 이는 Cu의 확산에 의한 상자성 혼합층의 증가와 반강자성석으로 결함된 자성층간의 배열의 변화가 그 원인이다.