• The Journal of Korean Academy of Prosthodontics
• /
• v.28 no.1
• /
• pp.165-191
• /
• 1990

Although a number of studies have been performed to assure that residual stress caused by a mismatch of alloy porcelain thermal expansion can contribute to clinical failure of a ceramometal restoration, the interactive influence of cooling rate on the magnitude of thermal expansion difference and on bond strength between them have not been extensively analyzed. The objective of this study was to determine the influence of cooling rate and the number of firing cycles on the expansion mismatch and the flexural failure resistance of metal porcelain strip. Tested alloys included one Pd-Ag alloy, one Ni-Cr-Be alloy with two kinds of porcelain, Vita and Ceramco. Metal specimens were cast into rods with a height of 13mm and a diameter of 5mm. Subsequently, the castings were subjected to scheduled firing cycles without porcelain. And the porcelain specimens after being fired were trimmed into a bar with a final dimension of $5{\times}5{\times}25mm$. Thermal expansions of the alloys and porcelains were measured by using a push rod or a differential dialometer respecitvely. Porcelain glass transition temperatures and expansion values were derived alloy-porcelain pairs were assessed by comparing expansion values of the components at a porcelain glass transition temperature. Calculations were made using combinations of a Ni-Cr alloy or Pd-Ag alloy with each of two porcelain products. Metal-porcelain strip specimens were subjected to four point loading in an Instron testing machine until crack occured at the metal-cramic interface at the time of sharp decrease of load on recorder. On the basis of this study, the following conclusions may be stated: 1. Regardless of the kinds of ceramometal combinations, both of calculated and experimental data revealed that the double fired specimens exhibited a significantly lower flexural strength. 2. By the rise of the amount of mismatch, bond strength were decreased. 3. Thermal expansion value of Pd-Ag alloys were higher than that of Ni-Cr alloys. 4. Expansion curves of metal were proportional to the increase of temperature and were not affected by the experimental conditions, however porcelains did not show the same magnitude of metal, and a shift of the glass transition temperature to higher temperatures was observed when cooled rapidly 5. Alloy-porcelain thermal compatibility appeared more dependent on the porcelain than the alloy.

• The Journal of Korean Academy of Prosthodontics
• /
• v.29 no.1
• /
• pp.111-137
• /
• 1991

Although a number of studies have been performed to assure that residual stress caused by a mismatch of alloy porcelain thermal expansion can contribute to clinical failure of a ceramometal restoratoin, the interactive influence of cooling rate on the magnitude of thermal expansion difference and on bond strength between them have not been extensively analyzed. The objective of this study was to determine the influence of cooling rate and the number of firing cycles on the expansion mismatch and the flexural failure resistance of metal porcelain strip. Tested alloys included one Pd-Ag alloy, one Ni-Cr-Be alloy with two kinds of porcelain, Vita and Ceramco. Metal specimens were cast into rods with a height of 13mm and a diameter of 5mm. Subsequently, the castings were subjected to scheduled firing cycles without porcelain. And the porcelain specimens after being fired were trimmed into a bar with a final dimension of 5 x 5 x 25mm. Thermal expansions of the alloys and porcelains were measured by using a push rod or a differential dialometer respectively. Porcelain glass transition temperatures and expansion values were derived alloy- porcelain pairs were assessed by comparing expansion values of the components at a porcelain glass transition temperature. Calculations were made using combinations of a Ni-Cr alloy or Pd-Ag alloy with each of two porcelain products. Metal- porcelain strip specimens were subjected to four point loading in an Instron testing machine until crack occured at the metal-cramic interface at the time of sharp decrease of load on recorder. On the basis of this study, the following conclusions may be stated : 1. Regardless of the kinds of ceramometal combinations, both of calculated and experimental data revealed that the double fired specimens exhibited a significantly lower flexural strength. 2. By the rise of the amount of mismatch, bond strength were decreased. 3. Thermal expansion value of Pd-Ag alloys were higher than of Ni-Cr alloys. 4. Expansion curves of metal were proportional to the increase of temperature and were not affected by the experimental conditions, however porcelains did not show the same magnitude of metal, and a shift of the glass transition temperature to higher temperatures was observed when cooled rapidly. 5. Alloy- porcelain thermal compatibility appeared more dependent on the porcelain than the alloy.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.5
• /
• pp.462-472
• /
• 2017

Sunken vessels on major fairways can cause many problems in terms of maritime safety and the marine environment. In order to prevent secondary marine pollution accidents caused by sunken vessels, information on sunken vessels has been collected, a risk assessment has been conducted, and the relevant vessels are being managed according to the results of each assessment. However, there is still a demand for improvements. The most important of the improvement plans is a paradigm shift. In other words, the management of sunken vessels needs to be transformed according to a new paradigm to manage all sunken vessels within three years from the time of sinking. Legislative improvements are also needed for the reporting system for sunken vessels, risk assessment tools, the implementation of risk mitigation measures, and criteria for the implementation cost of risk mitigation measures. In addition, close coordination between marine pollution response and sunken vessel management efforts is needed. As the division of duties between the Korea Coast Guard and the Ministry of Oceans and Fisheries is vague, collaboration between the two ministries is required. Close collaboration is also needed between the departments of navigation safety management and sunken vessel management. Therefore, it is necessary to more clearly establish the relationship between the two systems and create a synergy effect between the two administrative operations using the results of the risk assessment in the Marine Environment Management Act to determine the navigational risk posed by obstacles with regard to the Maritime Safety Act.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.31 no.3
• /
• pp.247-255
• /
• 1995

This paper describes a personal computer(PC) based color fish finder to improve some problem of the commercial one. The commercial fish finder has no function of the echo data logging and replaying. The authors developed two types of the PC based color fish finder. One is a master type composed of a PC, a digital input-output board, and analog to digital converting (A/D) board and an ultrasonic transceiver unit, the other is a slave type composed of a PC and an A/D board. To test the performances of the master type experiments were carried out in air and in a water tank. It is found that the designed master type fish finder displays very well an eight-colored echogram by one dot resolution to the left side of the PC monitor. Also, the depth of echo signal was corresponds very well to the range from the transducer to a target. The sampling interval of echo signal is about 0.1m and the time of A/D conversion is 30 $\mu$sec. On the other hand, to test the performances of the slave type a raw data of echo signals from a data logger was supplied directly or via RF transceivers to the slave type one. From this experiment, it is confirmed the slave type is useful to replay the echo signal from the data logger or a telesounder.

• Journal of The Korean Association For Science Education
• /
• v.42 no.2
• /
• pp.253-264
• /
• 2022

The purpose of this study is to examine the practice of scientists from the perspective of Ian Hacking's 'creation of phenomena'. Scientific phenomena, according to Hacking, are regular and do not exist in nature without the intervention of scientists or experimental tools. This study tries to derive scientific educational meaning by analyzing the thoughts and episodes of the 'Sontanda (inter-individual variability)' phenomenon experienced by four life scientists. The Sontanda phenomenon is a common term used by scientists to describe phenomena in which findings do not appear consistently even when studies are carried out using the same experimental procedure and materials. The following four educational implications were discovered as a result of the research. First, we confirmed the importance of embodied knowledge, or non-verbal knowledge, which solves issues by making appropriate judgments and reactions at all times, rather than simply becoming accustomed to the experimental method. This argues that propositional knowledge and non-verbal knowledge should be handled equally in order to provide students with a practical scientific inquiry. Second, we tried to reconsider the picture of the experiment. The phenomenon revealed in the interviews of scientists is rare, and it takes a long time to stabilize the phenomenon. On the other hand, the image of school experiments is always positive and consistent, necessitating a shift in perspective. Third, the precise meaning of scientific practice could be confirmed. This study confirms that scientists use their knowledge effectively in line with the circumstances, and we examined strategies to apply scientific practice to school instruction based on this. Finally, by provoking uncertainty, the Sontanda phenomena may give students with an opportunity to engage in meaningful scientific involvement. By breaking away from the cookbook experiment, this study expects school experimental education to help in efforts to experience scientific practice.

• Archives of design research
• /
• v.13 no.3
• /
• pp.281-292
• /
• 2000

Today, the rapid economic growth and emerging new trends have been changed radically throughout the society and they especially have affected the changes of life-style and the diversity of residents'demands in housing life. This changes of life have brought the shift in family form from traditional type, thus new phase of nuclear family means that it makes on the whole, variable family forms such as single family, non-blood one, a generation one and so on. It therefore is time that we should not only explore current housing plans, but envisage concept of new living space to satisfy latent need of the occupants. But the forms, in spite of the diversity of user's needs and the change of life-style, of many houses as many apartment and tenement houses supplied so far have been clearly limted, and housing policy of the mass-supply causes monotonous space composition, over-occupation and non-changeability. Now, the collective houses have some limits owing to the commoness and assemblage, but they have failed to keep up with the variable and changeable life-style of residents. These problems, to put it concretely, lead to increasing needs for the number of rooms in proportion to family members, for the change of behavior using the space. We therefore need to propose the new living space. As the current plans for designing house are based on the average life-style of people, they can not cope with variable demands of the resident. For that reason, this paper will propose the manual space system as an alternative for it and the goal is to suggest new furniture system which we need to create the flexibility of living space.

• Korean Journal of Cognitive Science
• /
• v.10 no.3
• /
• pp.51-66
• /
• 1999

Selective attention induces perceptual distortions. ranging from repulsion of objects located near the attended area(Suzuki & Cavanagh. 1997) to magnification of the u unattended objects (Tsal & Shalev. 1996). Two hypothetical mechanisms have been p postulated: a shift of receptive fields' positions away from the locus of attention(receptive-field-recruitment hypothesis) or the enlargement of perceived space around the a attended location(space-enlargement hypothesis). The present study distinguished between these hypotheses by investigating the spatial and temporal properties of attention-induced d distortions. Perceptual judgements on vernier alignment. line tilt. line length were used to measure attention-induced changes in perception. Attention was induced exogenously(by blinking a specific set of dots around the test stimuli} or endogenously(by instructing the subject to selectively attend the dots). After inducing attention. the test stimuli were briefly flashed. A staircase method was used to measure the attentional effect. A vertical line was perceived as repelled from the locus of attention. and a line segment appeared longer when attention was given to its vicinity. The effects decreased as the distance between the locus of attention or the time between the onset of attention and the stimulus presentation increased. The results imply that the space-enlargement hypothesis provides a better explanation for the attention-induced changes in perception than the receptive-field-recruitment hypothesis.

• Journal of Korean Society of Archives and Records Management
• /
• v.18 no.1
• /
• pp.129-154
• /
• 2018

It is time to prepare for the imminent development from the field of records management through decentralization to the records management of the new age in accordance with the flow of decentralization. To overcome a centralized record management system, more archives should be established to realize autonomous and decentralized records management. In accordance with the shift to a full-scale electronic record management environment, the appropriateness and effectiveness of the three-phase system of processing-archival-permanent record management based on physical transfer should be reviewed in terms of transfer cost and work efficiency. The archives should function as institutional archives to carry out the continuous volume record management and the autonomous record management at the institution level. This study examined the possibilities and implications of the archives to expand their functions as archives of institutions for the decentralization of record management and information governance orientation. In addition, the study diversified the types of records management institutions as a way to accomplish this and determined a way to design the functions of archives that integrate the current-end-end-end records management. At each level, institutions should set up archives based on their circumstances and aim at information governance at the level of each archive. Moreover, each archive level should establish a horizontal network to govern record information management.

• Journal of the Korean Society of Safety
• /
• v.35 no.1
• /
• pp.87-96
• /
• 2020

The purpose of this paper is to develop a fire HRA (Human Reliability Analysis) procedure for full power operation of domestic NPPs (Nuclear Power Plants). For the development of fire HRA procedure, the recent research results of NUREG-1921 in an effort to meet the requirements of the ASME/ANS PRA Standard were reviewed. The K-HRA method, a standard method for HRA of a domestic level 1 PSA (Probabilistic Safety Assessment) and fire related procedures in domestic NPPs were reviewed. Based on the review, a procedure for the fire HRA required for a domestic fire PSA based on the K-HRA method was developed. To this end, HRA issues such as new operator actions required in the event of a fire and complexity of fire situations were considered. Based on the four kinds of HFE (Human Failure Event) developed for a fire HRA in this research, a qualitative analysis such as feasibility evaluation was suggested. And also a quantitative analysis process which consists of screening analysis and detailed analysis was proposed. For the qualitative analysis, a screening analysis by NUREG-1921 was used. In this research, the screening criteria for the screening analysis was modified to reduce vague description and to reflect recent experimental results. For a detailed analysis, the K-HRA method and scoping analysis by NUREG-1921 were adopted. To apply K-HRA to fire HRA for quantification, efforts to modify PSFs (Performance Shaping Factors) of K-HRA to reflect fire situation and effects were made. For example, an absence of STA (Shift Technical Advisor) to command a fire brigade at a fire area is considered and the absence time should be reflected for a HEP (Human Error Probability) quantification. Based on the fire HRA procedure developed in this paper, a case study for HEP quantification such as a screening analysis and detailed analysis with the modified K-HRA was performed. It is expected that the HRA procedure suggested in this paper will be utilized for fire PSA for domestic NPPs as it is the first attempt to establish an HRA process considering fire effects.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.6
• /
• pp.55-64
• /
• 2017

High-capacity, high-definition image applications need to process considerable amounts of data at high speed. Accordingly, users of these applications demand a high-speed parallel execution system. To increase the speed of a parallel execution system, Park (2004) proposed a technique, called MAMS (Multi-Access Memory System), to access data in several execution units without the conflict of parallel processing memories. Since then, many studies on MAMS have been conducted, furthering the technique to MAMS-PP16 and MAMS-PP64, among others. As a memory architecture for parallel processing, MAMS must be constructed in one chip; therefore, a method to achieve the identical functionality as the existing MAMS while minimizing the architecture needs to be studied. This study proposes a method of miniaturizing the MAMS architecture in which the architectures of the ACR (Address Calculation and Routing) circuit and MMS (Memory Module Selection) circuit, which deliver data in memories to parallel execution units (PEs), do not use the MMS circuit, but are constructed as one shift and conditional statements whose number is the same as that of memory modules inside the ACR circuit. To verify the performance of the realized architecture, the study conducted the processing time of the proposed MAMS-PP64 through an image correlation test, the results of which demonstrated that the ratio of the image correlation from the proposed architecture was improved by 1.05 on average.