• Journal of Advanced Marine Engineering and Technology
• /
• v.10 no.2
• /
• pp.136-145
• /
• 1986

The perfect and accurate methods to control the wear are not made clear so far. For this phenomenon only mating surface has been studied. In order to control the wear the essence of it has to be made clear. It is reported that adhesive wear might occure as a result of plastic deformation, the fracture and removal or transfer asperities on close contacting surfaces. On this view point the plastic flow was attempted to compare with fluid or electromagnetic flow. The partial differential equations of equilibrium for the plane strain deformation will make use of the method of characteristics. The characteristic curves or characteristics of the hyperbolic equation coincide with the slip lines by R. Hill's papers. By Hencky's stress equation, it is evident that if P and .phi. are prescribed for a boundary condition then it may be possible to proceed along constant .alpha. and .betha. lines to determine the value of the hydrostatic pressure everywhere in the slip line field net work. A wedge formation mechanism has been considered for an explanation of this matters. The analysis shows that there is a critical value, which depends on the hardness ratio and the shear stress on the interface, for the top angle of asperity is less than this critical value, the asperity can yield plastically despite of being harder than the mating surface.

• Journal of the Korean Ceramic Society
• /
• v.50 no.1
• /
• pp.43-49
• /
• 2013

${\beta}$-SiC was deposited onto a graphite substrate by a LPCVD method and the effect of the crystallographic orientation on mechanical properties of the deposited SiC was investigated. The deposition was performed at $1300^{\circ}C$ in a cylindrical hot-wall LPCVD system by varying the deposition pressure and total flow rate. The texture and crystallographic orientation of the SiC were evaluated by XRD. The deposition rate increased linearly with the gas flow rate from 800 sccm to 1600 sccm. It also increased with the pressure but became saturated above a total pressure of 3.3 kPa. In the range of 3.3 - 10 kPa, the preferred orientation changed from the (220) and (311) planes to the (111) plane. The hardness and elastic modulus showed maximum values when the SiC had the (111) preferred orientation, though it gradually decreased upon a change to the (220) and (311) preferred orientations.

• Wind and Structures
• /
• v.20 no.5
• /
• pp.661-682
• /
• 2015

This study investigates the use of time-frequency coherence analysis for detecting and evaluating coherent "structures" of surface pressures and wind turbulence components, simultaneously on the time-frequency plane. The continuous wavelet transform-based coherence is employed in this time-frequency examination since it enables multi-resolution analysis of non-stationary signals. The wavelet coherence quantity is used to identify highly coherent "events" and the "coherent structure" of both wind turbulence components and surface pressures on rectangular prisms, which are measured experimentally. The study also examines, by proposing a "modified" complex Morlet wavelet function, the influence of the time-frequency resolution and wavelet parameters (i.e., central frequency and bandwidth) on the wavelet coherence of the surface pressures. It is found that the time-frequency resolution may significantly affect the accuracy of the time-frequency coherence; the selection of the central frequency in the modified complex Morlet wavelet is the key parameter for the time-frequency resolution analysis. Furthermore, the concepts of time-averaged wavelet coherence and wavelet coherence ridge are used to better investigate the time-frequency coherence, the coherently dominant events and the time-varying coherence distribution. Experimental data derived from physical measurements of turbulent flow and surface pressures on rectangular prisms with slenderness ratios B/D=1:1 and B/D=5:1, are analyzed.

• The KSFM Journal of Fluid Machinery
• /
• v.6 no.3 s.20
• /
• pp.21-27
• /
• 2003

Dispersion of coolant jets in a film cooling flow field is the result of a highly complex interaction between the film cooling jets and the mainstream. In order to investigate the effect of blowing ratios on the film cooling of a turbine blade, cylindrical body model is used. Mainstream Reynolds number based on the cylinder diameter is $7.1{\times}10^4$. The effects of coolant flow rates are studied for blowing ratios of 0.7, 1.0, 1.3 and 1.7, respectively. The temperature distribution of the cylindrical model surface is visualized with infrared thermography (IRT). Results show that the film cooling performance could be significantly improved by the shaped injection holes. For higher blowing ratio, the spanwise-diffused injection holes are better due to the lower momentum flux away from the wall plane at the hole exit.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.2
• /
• pp.286-294
• /
• 1988

The thermal stress intensity factors (TSIF's) for the cusp cracks such as hypocycloid crack, symmetric airfoil crack and symmetric lip crack are determined by using Bogdanoff's complex variable approaches in plane thermoplasticity. The results are expressed in terms of the periodic functions of the direction of uniform heat flow. The TSIF's are shown to be sensitive to both the direction of uniform heat flow and be thermal boundary conditions. It is also shown that Fourence's solutions for an insulated circular hole and Sih's solutions for an insulated Griffith crack are derived from the results of the stress and displacement fields for the hypocycloid crack and the TSIF's for the various cusp cracks, respectively.

• ETRI Journal
• /
• v.32 no.2
• /
• pp.241-247
• /
• 2010

We propose and experimentally demonstrate a service-aware optical transport system. The proposed service-aware optical transport system makes a flow based on service type and priority of traffic. The generated flow is mapped to a corresponding sub-${\lambda}$ for transport over an optical network. Using sub-${\lambda}$ provided by the centralized control plane, we could effectively provide quality-of-service guaranteed Ethernet service and best-effort service simultaneously in a single link. The committed information rate (CIR) traffic and best-effort traffic are assigned to different sub-${\lambda}s$. The bandwidth of the CIR traffic is guaranteed without being affected by violation traffic because the bandwidth is managed per each sub-${\lambda}$. The failure detection time and restoration time from a link failure is measured to be about 60 ${\mu}s$ and 22 ms, respectively, in the ring network. The measured restoration time is much smaller than the 50 ms industry requirement for real-time services. The fast restoration time allows the proposed service-aware optical transport system to offer high availability and reliability which is a requirement for transport networks.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.3
• /
• pp.497-504
• /
• 1988

The steady state thermal stress intensity factors (TSIF's) are analyzed for hypocycloid, symmetric airfoil and symmetric lip type rigid inclusions embedded in infinite elastic solids, using Boganoff's complex variable approach in plane thermoplasticity. Two thermal conditions are considered, one with an uniform heat flow disturbed by an insulated rigid inclusion of cusp crack shape and the other with an uniform heat flow disturbed by a rigid inclusion of cusp crack shape with fixed boundary temperature. The tendencies of TSIF's for rigid inclusions of cusp crack shape are somewhat different from those of traction free cusp cracks. However, if k=-1, the non-dimensionalized TSIF's for rigid inclusions of cusp crack shape become those of traction free cusp cracks like the tendencies of the SIF's under mechanical loading conditions. The thermal stress and displacement components for a rigid circular inclusion of radius Ro are drived from the results of a hypocycloid crack type rigid inclusion.

• The Journal of Engineering Geology
• /
• v.22 no.1
• /
• pp.83-94
• /
• 2012

Slopes are commonly formed both above and below roads located in mountainous terrain and along riversides. The Buk-sil site, a cut slope formed below the road, collapsed in October, 2010. A field investigation determined the causes of failure as improper drainage of valley water from the slope above the road and direct seepage of road-surface water. These factors may have accelerated the collapse via complex interaction between water and sub-surface structures such as bedding. Projection analysis of the site showed the possible involvement of plane, wedge, and toppling failure. Safety factors calculated by Limit Equilibrium Analysis for plane and wedge failure were below the standard for wet conditions. The wetness index, analyzed using topographic factors of the study area, was 9.0-10.5, which is high compared with the values calculated for nearby areas. This finding indicates a high concentration of water flow. We consider that water-flow control on the upper road is crucial for enhancing slope stability at the Buk-sil site.

• The KSFM Journal of Fluid Machinery
• /
• v.2 no.3 s.4
• /
• pp.17-23
• /
• 1999

In the present numerical analysis, investigation of the effect of blade loadings from design shape on the slip factor variation was studied. Both the Eckardt radial bladed impeller and the backswept impeller were analyzed. In addition, a new design of the blade profile was arbitrarily attempted to generate a center-loading pattern in the original backswept impeller. Three dimensional compressible Navier-Stokes flow analysis with the Baldwin-Lomax turbulence model was applied to get the numerical slip factor at each impeller exit plane using the mass-averaging technique. The numerical slip (actors are in good agreement with the experimental ones and the Wiesner's slip factors deviate further from the numerical and experimental ones in both backswept impellers. Deviation angles and meridional channel loadings are found in no relation with the trend of change of the slip factor. Blade-to-blade loadings in midspan location are, however, found to have a direct relationship, especially at the sections where maximum loadings we to be expected. That information can be utilized in establishing an improved expression for slip factors in the future.

• Journal of KSNVE
• /
• v.6 no.6
• /
• pp.709-715
• /
• 1996

In recent years, the piping vibration in many Power Plants is being increased by the aged generating facilities due to a long time use. Generally, the pressure fluctuations associated with the flow-induced excitations in this case are broadband in nature. Mainly, the dominant sources of vibration are a vortex-shedding, plane waves and boundary layer turbulence. The peak level of the spectrum is proportional to the dynamic head. A severe disturbance in pipeline results in the generation of intense broadband internal sound waves which can propagate through the piping system. The characteristic frequencies of operating loads of 20%, 57%, 70%, 100% are 4 - 6 Hz and coincide with the results from impact hammering test and FEM analysis. We chose the wire energy absorbing rope restraint as a vibration reduction method after reviewing the various conditions such as site, installing space and economic cost etc. After installation, the vibration level was reduced about 54% in velocity.