• 전자공학회논문지 IE
• /
• v.44 no.1
• /
• pp.15-19
• /
• 2007

A study to have read does an improvement of an error restoration technology based on the edge direction interpolation that a stop image cared for inside frame correction more than with an image restoration way of a transfer error or with an aim. A way proposed to is based on edge direction detection method of a block utilizing the edge direction which will adjust a part damaged a sweater to a remaining part here. The rest of error pixel used non linear Midian filter for process later data information by the final stage and did interpolation. The examination result shows a good recuperation tendency and low accounts time of a way proposed to realization possibility of a real time image processing.

• Smart Structures and Systems
• /
• v.17 no.1
• /
• pp.31-43
• /
• 2016

Applications of ultrasonic tomography to concrete structures have been reported for many years. However, practical and effective application of this tool for nondestructive assessment of internal concrete condition is hampered by time consuming transducer coupling that limits the amount of ultrasonic data that can be collected. This research aims to deploy recent developments in air-coupled ultrasonic measurements of solids, described in Part 1 of this paper set, to concrete in order to image internal inclusions. Ultrasonic signals are collected from concrete samples using a fully air-coupled (contactless) test configuration. These air coupled data are compared to those collected using partial semi-contact and full-contact test configurations. Two samples are considered: a 150 mm diameter cylinder with an internal circular void and a prism with $300mm{\times}300mm$ square cross-section that contains internal damaged regions and embedded reinforcement. The heterogeneous nature of concrete material structure complicates the application and interpretation of ultrasonic measurements and imaging. Volumetric inclusions within the concrete specimens are identified in the constructed velocity tomograms, but wave scattering at internal interfaces of the concrete disrupts the images. This disruption reduces defect detection accuracy as compared with tomograms built up of data collected from homogeneous solid samples (PVC) that are described in Part 1 of this paper set. Semi-contact measurements provide some improvement in accuracy through higher signal-to-noise ratio while still allowing for reasonably rapid data collection.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.7A
• /
• pp.1063-1075
• /
• 2000

This paper proposes an adaptive error concealment technique for compressed video. Since redundancy is extracted out during compression process, compressed video is vulnerable to errors which occur during transmission of video over error prone networks such as wireless channels and Internet. Error concealment is a process of reconstructing video out of damaged video bit stream. We proved that scalable encoding is very useful for error concealment. Analysis of experiments shows that some part of image is better concealed by using base layer information and other part of image is better concealed by using previous frame information. We developed a technique which enables to decide which methodology is more effective, adaptively, based on motion vectors and regional spatial activity. We used H.263v2 for scalable encoding, but, our approach could be applied to all DCT based video codec.

• Journal of the Korean Society of Safety
• /
• v.28 no.3
• /
• pp.29-32
• /
• 2013

An aircraft made an emergency landing through the loss of capability controlling steering. A torsion link which is a part of steering apparatus has been adrift from the steering system and the bolt connected to the steering link has fractured. At the same time, the FLIR(Forward Looking Infrared Radar) mounted in front of the steering link has been also damaged. In the early of this investigation, we considered the failure of the FLIR had occurred first, that FLIR hit the steering link and finally the bolt fractured. The fractured section of the bolt has shown a beach mark and a dimple mark as well. The outside of the bolt has shown a large deformation by a heavy load. As a result, we have found out what the cause of the heavy load and the fractures for bolt, link and FLIR have occurred in what order.

• Journal of Information Processing Systems
• /
• v.16 no.5
• /
• pp.1129-1144
• /
• 2020

The thangka image inpainting method based on wavelet transform is not ideal for contour curves when the high frequency information is repaired. In order to solve the problem, a new image inpainting algorithm is proposed based on edge structural constraints and wavelet transform coefficients. Firstly, a damaged thangka image is decomposed into low frequency subgraphs and high frequency subgraphs with different resolutions using wavelet transform. Then, the improved fast marching method is used to repair the low frequency subgraphs which represent structural information of the image. At the same time, for the high frequency subgraphs which represent textural information of the image, the extracted and repaired edge contour information is used to constrain structure inpainting in the proposed algorithm. Finally, the texture part is repaired using texture synthesis based on the wavelet coefficient characteristic of each subgraph. In this paper, the improved method is compared with the existing three methods. It is found that the improved method is superior to them in inpainting accuracy, especially in the case of contour curve. The experimental results show that the hierarchical method combined with structural constraints has a good effect on the edge damage of thangka images.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2003.11a
• /
• pp.133-137
• /
• 2003

When a light is projected upon a material, part of its radiation energy is absorbed and the rest is reflected or transmitted according to the nature of the material. The molecules of the substance absorbing a light obtains the radiation energy to the wavelength of the light to make photochemical degradation by ultraviolet ray or thermal reactions like physical damage by infrared ray. The degree of damage by radiation energy varies to the substances of materials, the spectral power distribution of the light source and the duration of irradiation. Because the damage brings about a devaluation of material and once damaged, it is irretrievable, it is necessary to minimize the damage and conserve the native quality of a material by a protective lighting system. A measuring system was set up to measure the temperature rise of each sample by infrared radiation from light sources. And the temperature rise and temperature distribution by various infrared lamps were measured with varying time.

• Architectural research
• /
• v.13 no.4
• /
• pp.53-60
• /
• 2011

Damage detection algorithms based on a one-dimensional beam model can detect damage within a beam span caused by flexure only but cannot detect damage at a joint with prescribed boundary conditions or at the middle part of a beam section where the neutral axis is located. Considering the damage at a welded joint of beam elements in steel structures and modeling the damage with twodimensional plane elements, this study presents a new approach to detecting damage in the depth direction of the joint and beam section. Three damage scenarios at the upper, middle, and lower parts of a welded joint of a rectangular symmetric section are investigated. The damage is detected by evaluating the difference in the receptance magnitude between the undamaged and damaged states. This study also investigates the effect of measurement locations and noise on the capability of the method in detecting damage. The numerical results show the validity of the proposed method in detecting damage at the beam's welded joint.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.798-800
• /
• 2003

Recently, in optical storage device technical trends, the size of optical drive is slimmer to adopt notebook computer and the power of actuator is higher to achieve the high transfer rate. However, these trends of optical disc drives tend to increase the temperature of the actuator part, it causes some problems on the performance of optical parts - the resonance frequency of the actuator is down to lower band and the objective lens, coil and magnet are easily damaged. In this study, to overcome these thermal problems, the numerical simulations of heat transfer were performed. As the result of simulations, the thermal characteristic of the hybrid actuator is better than the previous design. And, it shows the good dynamic performance in experiment.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.767-770
• /
• 2000

A novel process is newly developed for building RP(Rapid Prototyping) parts using a sheet lamination technique. The build process of existing sheet lamination type RP machines consists of the following steps : feeding, lamination and cutting. In this process, the laminated part of an object is often scratched by a cutter or damaged by a laser beam due to the cutting operation preceded by lamination, In addition, decubing of the unused portion from the laminated block is difficult. In the new process, cutting operation is performed before lamination. The cutting operation takes place while a paper sheet is firmly attached on the plate using electrostatic force. Then liquid glue is applied to the calculated region of the given contour for lamination. The process aims to manufacture a $2k RP machine, what we call the Freeform Mater I, that can use A4 or latter-size used papers. A prototype machine that demonstrates the design concept is built and further research issues are discussed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.815-820
• /
• 2000

The early damage detection of large structures is very important to prevent the disaster due to its global failure. In this paper, a damage detection method of the beam-analogy structure based on the wavelet transformation of mode shape is presented. This can effectively detect the singularity of mode shape caused to the inconsistency of bending moment and shear force at the damaged part using the discrete wavelet and its inverse transforms. To investigate the validity and the applicability of the presented damage detection method, numerical simulation and experiment are carried out for the idealized beam and the real ship structures.