• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2005년도 전력전자학술대회 논문집
• /
• pp.750-753
• /
• 2005

This paper presents a method of detecting rotor position for single phase Switched Reluctance Motors(SRMs) using searchs coil. In the single phase SRM, mainly Hall effect sensors or photo interrupters have been used to detect the rotor position. But these sensors cause high cost and increase the volume of the motor, Furthermore when the motor is used in very hostile environment like high temperature or pressure, its reliability goes down. In this paper, low cost and robust characteristics of rotor position detection method are focused in order to compensate for disadvantage of existing sensors. Search coils wound around the stator pole are used for detection of the rotor position in single phase SRM. Rotor position detection is achieved through electromotive force patterns induced by time-varying flux linkage in the search coil. The validity of the method is verified by experimental results.

• 전기학회논문지
• /
• 제57권5호
• /
• pp.789-796
• /
• 2008

This paper describes a single-phase active power filter based on a newly developed digital controller. The developed controller utilizes FFT(Fast Fourier Transform) algorithm to extract the reference signal from the load current, considering the phase-angle delay of each order of harmonics. Optimized technique was applied for whole control algorithm to implement the real-time operation of developed controller. The performance of developed controller for a single-phase active power filter was verified through computer simulations with PSCAD/EMTDC. The feasibility of hardware implementation was confirmed by building and testing a prototype. The developed digital controller for a single-phase active power filter can compensate the harmonic current generated by the power supply for digital equipment.

• 대한조선학회논문집
• /
• 제41권6호
• /
• pp.65-74
• /
• 2004

The inherent strain method is known to be very efficient in predicting the deformation of steel plate by line heating. However, in the actual line heating process in shipyard, the rapid quenching changes the phase of steel. In this study, In order to consider additional effects under phase transformation, inherent strain regions were assumed to expand. Also, when calculating inherent strain, material properties of steel in heating and cooling are applied differently considering phase transformation. In this process, a new method which can reflect thermal volume expansion of martensite is suggested.8y the suggested method, it was possible to predict the plate deformations by line heating more precisely.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1988년도 전기.전자공학 학술대회 논문집
• /
• pp.422-425
• /
• 1988

The structure consisting of an E-plane dielectric slab partially filling a rectangular waveguide is examined with attention on those higher order mode propagation characteristics that are relevant to the design of nonreciprocal remanence ferrite phase shifters. The mechanisms for the elimination of $LSE_{11}$, $LSM_{11}$, $LSE_{12}$ modes are introduced. Experimental verification of elimination of higher order mode is shown in the form of insertion loss measurements.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 Proceedings ICPE 01 2001 International Conference on Power Electronics
• /
• pp.591-599
• /
• 2001

The paper identifies a severe form of core saturation instability in an DC/AC interaction system. It then seeks solutions to the problem by HVDC control means. This is achieved by a proper design of the Voltage Dependent Current Order Limiter (VDCOL), the Current Regulator and Timing Pulse generator. Supplementary control loops have also been introduced to result in a satisfactory performance as compared to that obtained one with the use of uncharacteristic harmonic filter on the AC side. Robustness of all the options has been demonstrated through recovery performance of the DC link in response to both I-phase and 3-phase 5 cycle faults on both rectifier and inverter commutating buses.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 전기학술대회논문집
• /
• pp.1170-1175
• /
• 2005

This paper is analyzed the characteristic of multi-phase inverter for the electric propulsion system. Two BLDC motors with 3 and 7 phases are designed with these features in order to simulate the effect of increasing the number of phases. From the simulation results, the 7-phase given better performance in terms of torque pulsation. Also, the torque pulsation can be reduced further by increasing the number of phases.

• 대한의용생체공학회:의공학회지
• /
• 제11권1호
• /
• pp.13-18
• /
• 1990

Frequency responses of ambulatory electrocardiogram systems were measured. Phase shift was assessed by our improved Wagner's method. The characteristics of the systems were found much worse than that of ordinary ECG equipment both in gain and phase responses. The decay of -3dB in amplitude observed in 0.2Hz and the lead of 45 dog in phase was observed in 0.6Hz. In order to investigate which of these 2 responses play major role in generating false S -T deviation, mathe- matical filters were Composed in a computer and actual ECGs were fed. The false S-T deviation were found to be caused mostly by enormous lead in phase, and then, the compensation circuit to diminish the lead in phase was inserted in the commercial systemes. The compensated systems showed no false deviation in S-T segment.

• 한국운동역학회지
• /
• 제13권3호
• /
• pp.277-291
• /
• 2003

This study was designed to examine the kinematic factors in the phase during the marche fente motion. For this study, the subjects were 5 elite male fencing players. The direct linear transformation (DLT) method was used in calculating 3-D coordinate of the digitized body parts. The cubic spline function was used for smoothing and the kinematic data for displacement, velocity, angle variables were calculated for Kwon3d ver 2.1. And the following conclusions were drawn; 1. It show that the marche phase appeared to longer time than the pante phase In the performance time. For the fast attack, it showed that the subjects should be moving in a short stride width. 2. For a fast and stable movement posture in the marche phase, the vertical change of COG must be maintain the same position as possible, but all subjects appeared to decrease the COG because of a excessive the knee flection. 3. In the COG velocity change, all the subjects showed to the same change in both the marche and the fente phase. However in the attack extremity velocity, it increased velocity in order of upper arm, fore arm, and hand in the marche phase, but it showed different velocity among each subjects at the moment of stabbing. So that in order to do effective stabbing, they have to extend their upper extremity max and do faster the distal segment than the proximal segment. 4. It showed to take a fast and stable movement, because some subjects showed the big anteroposterior angle of the trunk flexed max shoulder angle and elbow angle of their attack arm and the other upper extremity.

• Journal of Power Electronics
• /
• 제2권4호
• /
• pp.297-304
• /
• 2002

The paper identifies a severe form of core saturation instability in a DC/AC interaction system. It then seeks solutions to the problem by HVDC control means. This is achieved by a proper design of the Voltage Dependent Current Order Limiter (VDCOL), the Current Regulate. and Timing Pulse generator. Supplementary control loops have also been introduced to result in a satisfactory performance as compared to that obtained one with the use of uncharacteristic harmonic filter on the AC side. All the options have been demonstrated through recovery performance of the DC link in response to both 1-phase and 3-phase 5 cycle faults on both rectifier and inverter commutating buses.

• 한국정밀공학회지
• /
• 제14권1호
• /
• pp.126-141
• /
• 1997

The purpose of this research is to develope a FEM program for analyzing solidification processes of axisymmetric casting, considering phase changes and the contact between the metal and mold. Tempera- ture recovery method is employed fro considering the phase changes releasing the latent heat and the coin- cident node method is used for calculating the amount of heat transfer between the metal and mold. Tan- gent modulus algorithm is adopted for calculating flow stress and a gap element is employed for modeling the interface between the mold and metal in finding deformed shapes. In order to verify the developed program, axisymmetric aluminum and steel casting processes are simulated. Temperature distribution, phase front position, and shrinkage and porosity creation are compared with measurements, FIDAP results, and good agreements are examined.