• Korean Journal of Agricultural Science
• /
• v.38 no.1
• /
• pp.115-120
• /
• 2011

20% of total energy use to sustain temperature of building inside. In this reasons, researchers effort to improve the thermal insulation capacity with new wall system. Using appropriate materials and consisting new wall system should considered in energy saving design. OSB(Oriented strand board), Larch lining board used to consist wall system. $2{\sim}6$ Larch lining board has tongue & groove shape for preventing moisture. Comparing with gypsum board and green timber lining board as interior sheathing material, temperature difference of Green timber wall system was bigger than temperature difference of gypsum board wall system. This aspects indicate that Green timber wall system was revealed higher thermal insulation property than gypsum board wall system. Gypsum board portion transfer heat easily because temperature difference gradient of gypsum board wall system was smaller than OSB wall system. Total temperature variation shape of G-4-S and G-6-S show similar model but, temperature variation shape in green timber wall portion assume a new aspect. The purpose of this study was that possibility of thermal insulation variation and new composition of wall system identify to improve thermal insulation performance. In the temperature case, this study shows possibility of improving thermal insulation performance. Humidity, sunshine and wind etc. should considered to determine building adiabatic properties.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.5
• /
• pp.1227-1234
• /
• 1994

A cold spot temperature control system for the batch annealing furnace has been established in order to reduce energy consumption which is essential to improve productivity and stabilize the properties of products. A relationship between annealing cycle time and gas flow rate is developed and also for the variation of coil cold spot temperature with time during heating, and actual temperature measurements at mid-width of each coil during soaking. The results of the temperature variation effect on the cold rolled steel sheet batch annealing are as follows. (1) Cooling rate increasing gradually with increasing atmospheric gas flow, but heating rate is hardly increasing without atmospheric gas component change. (2) In case of short time heating, the slowest heating part is the center of B coil and in case of ling time heating, the low temperature point moves from the center of coil to inside coil. (3) The outside of top coil is the highest temperature point under heating, which becomes the lowest temperature point under cooling. (4) Soaking time determination depends on the input coil width, and soaking time for quality homogenization of 1214 mm width coil must be 2 hours longer than that of 914 mm width coil.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.12 no.1
• /
• pp.44-51
• /
• 2009

In order to determine air temperature difference by canopy layer in the forest, air temperatures were observed at Seolleung Park, Gahngnam-ku, Seoul. from November 9, 2007 to November 8, 2008 by 10 minute interval. The data were analyzed in terms of diurnal variation based on annual and monthly temperature difference. Using calm, less cloudy and no rainy weather data, average air temperature difference between forest and grass was observed as $0.8^{\circ}C$. The maximum air temperature difference was observed at 22:10, 23:20, 23:30 and 23:40 by $2.13^{\circ}C$ and the minimum one observed at 13:00 by $-0.84^{\circ}C$ in diurnal variation. The maximum temperature difference occurred at 19 : 50 on September by $3.67^{\circ}C$, Overall the air temperature in the forest was higher than that of grass at night and lower in midday.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.148-151
• /
• 2005

This paper is concerned with the thermo-mechanical behavior and temperature dependent strain rate sensitivity of steel sheet for an auto-body. In order to Identify the temperature dependent strain rate sensitivity of SPRC35R and SPRC45E, uniaxial tension tests are performed with the variation of the strain rates from 0.001/sec to 200/sec, and the variation of environmental temperatures from $-40^{\circ}C\;to\;200^{\circ}C$. The thermo-mechanical response at the quasi-static state is obtained with the static tensile test and at the intermediate strain rate is from the high speed tensile test. The experimental results show that the strain rate sensitivity increases at low temperature and it decreases at high temperature. It means that as the strain rate getting increasing, the variation of flow stress is more sensitive on the temperature. The results also indicates that the material properties of SPRC35R is more depend on the changes of strain rates and temperature than those of SPRC45E.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.3 no.4
• /
• pp.173-180
• /
• 1979

Temperature distriburion in a hollow chlinder has been analyzed mathematically. Unsteady condition considered assumed a constant heat flux input from the inside. The results are compared with experimental results of surface temperature rise of a gun barrel during continuous firing. Their agreements are acceptable. Effects of various dimensionless parameters on the surface temperature rise are discussed. For small Biot numbers, the external survface temperature approaches more rapidly to the steady temperature. Temperature difference between internal and external surfaces becomes greater for small Biot number. Steady solution assumed that the gas temperature inside the cylinder varies periodically. Relative amplitude and phase angles between the gas temperature and the internal or external surface temperature are obtained. Phase angles become smaller for large radiancy of gas temperature variation, small external Biot number, or large internal biot number. Relative amplitudes become samller as radiancy of gas temperature variation and internal Biot number become smaller. or external Biot number becomes larger. The solution obtained in this paper can be applied to gun barrels, heat pipes used in heat excangers, and reciprocation engines.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.9 no.1
• /
• pp.55-62
• /
• 2006

Correlations between air-temperature variation and SST variation around Jeju Island have been studied with data JRMO($1924{\sim}2004$) and NFRDI($l971{\sim}2000$). Air-temperature has increased about $0.02^{circ}C/year$ for the period of $1924{\sim}2004$ but relatively high 0.035/year for the last 30 years. SST has increased about $0.024^{circ}C/year$ for the period of $1971{\sim}2000$ and relatively high $0.047^{circ}C/year$ in December. According to the analysis of time series of the two kind of variation, the SST and air-temperature are positively correlated. They are generally in phase, and SST anomaly is similar to air-temperature anomaly as well. Consequently, SST variation has high correlation with air-temperature variation around Jeju Island.

• Journal of Energy Engineering
• /
• v.24 no.2
• /
• pp.1-8
• /
• 2015

Wax deposition hinders oil flow assurance. Huge amount of money and time were required for mitigation of wax deposition in the oil field. For prediction and mitigation of wax deposition problem, Wax Appearance Temperature(WAT), which is the temperature at which the first wax crystals start to form, needs to be measured in advance. There is a standard method which is optical way to measure the WAT of transparent oil. However, standard method cannot be applied to opaque oil which is common produced oil in the field. In this study, WAT of three transparent oil samples were measured using heat flux variation analysis, viscosity variation analysis and density variation analysis, and compared with WAT measured by standard method. As a result, WAT measured by density variation analysis is the more reliable than heat flux variation analysis and viscosity variation analysis. WAT of two opaque oils were measured using density variation analysis.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.2
• /
• pp.349-357
• /
• 2007

The most sensitive part of the installed optical fiber fable is the optical loss variation of the splicing part according to the environmental changes. This paper presents the details of the experimental results of the external environmental changes on optical loss, such as bending, temperature variation, temperature variation after water osmosis and vibration. Through the bending test of optical fiber, rapid increase of optical loss was measured within the radius of 30mm. The result of optical loss variation within the temperature range of $-30^{\circ}C{\sim}60^{\circ}C$ is less than 0.02dB. It was confirmed that the maximum optical loss increased up to 0.2dB in case of water osmosis within the temperature range of $-40^{\circ}C{\sim}80^{\circ}C$. There is small optical loss variation of 0.01dB under the 1mm vibration test. The experimental results of this paper can be used as the reference data for the design of the optical fiber cable splicing enclosure to protect the optical loss variation due to environmental changes.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.45 no.4
• /
• pp.211-222
• /
• 2009

The fisheries resources by a set net in the coastal waters off Neungpo, Goeje Island from 2003 to 2004 were studied to determine species composition and catch variation. The main fishing period by a set net were from April to December in 2003 and from May to December in 2004. A total weight of 48 species caught through the survey period was 540,688.0kg. Most of them were 44 species of fishes and a few were 4 species of cephalopods. Dominant species was Trachurus japonicus accounting to 57.5% in total catch. Sub-dominant species were Trichiurus lepturus(12.9%), Engraulis japonicus(10.6%), Scomber japonicus(6.9%), Clupea pallasii(4.5%), Todarodes pacificus(2.8%) and Parapristipoma trilineaturm(1.3%). The remnant species showed a low catch, indicating the catch had less than 1% in total, respectively. T. japonicus and T. lepturus were caught throughout the survey period, but C. pallasii, Gadus macrocephalus, Oncorhynchus keta in low temperature season and Thunnus obesus in high temperature season. The fishing ground temperature was 11.7-24.0${^{\circ}C}$ in range and the catch by a set net was higher in autumn than in spring and in summer with the variation of fishing ground temperature. The annual catch by a set net was much higher in 2004 than in 2003 due to high temperature(>17${^{\circ}C}$) and the recruitment of T. japonicus from offshore seas. Therefore we concluded that the catch of Neungpo fishing ground by a set net was highly related to the variation of T. japonicus catch with fishing ground temperature.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.1C
• /
• pp.29-38
• /
• 2011

The smaller diameter cone penetrometer has been widely used to estimate the characteristics of local area due to high vertical resolution. The half-bridge cirucits have been adopted to measure the mechnical strength of soil through the smaller diameter cone penetrometer due to the limitation of the areas for configuring the full-bridge circuit. The half-bridge circuit, however, is known as being easily affected to the temperature variation. The objective of this study suggests the temperature-compensated method in mini-cones. The diameter and length of the mini-cone is designed to 15mm and 56mm. The load cell of the mini-cone is extended about 54mm on the behind of the mini-cone to reflect the only temperature variation. The full-bridge circuit is installed to measure the temperature-compensated values in the mini-cone and the half-bridge circuit is also organized to compare the temperature compensated values with uncompensated values. The seasonal variation tests are performed to define the effect of temperature variation under summer and winter temperature condition. The densification tests are also carried out to investigate temperature effects during penetration. The measured mechanical resistances with temperature-compensated method show more reliable and reasonable values than those measured by thermal uncompensated system. This study suggests that the temperature-compensated method of the mini-cone may be a useful technique to obtain the more reliable resistances with minimizing the temperature effect.