• 한국식품과학회지
• /
• 제27권1호
• /
• pp.129-133
• /
• 1995

배양환경이 효모 RNA 축적과 autolysis 효율에 미치는 영향을 알아보기 위하여 연속배양을 실시하였다. Dilution rate의 증가에 따라 균체내의 RNA 함량은 증가하여 dilution rate=0.35 $h^{-1}$에서 14.8%를 나타내었고, 더불어 RNA productivity와 specific RNA productivity도 증가하였다. 고정된 D=0.2 $h^{-1}$에서 최적 균체량은 배양온도 $30^{\circ}C$ 에서 얻어졌으나, RNA 함량은 배양온도가 낮아질수록 높은 값을 보여 $24^{\circ}C$에서 12.7%로 나타났다. 한편, autolysis 효율 측면에서 균체 생육속도가 증가할수록 효모 extract의 추출율은 감소하였고, 효모 extract의 분해율은 증가하는 경향을 보였으나, 배양온도는 효모 autolysis 효율에 큰 영향을 미치지 않았다.

• 한국표면공학회지
• /
• 제36권3호
• /
• pp.234-241
• /
• 2003

SiC nanorod was synthesized directly on Si substrate using hexamethyldisilabutane and Fe catalyst with (111) direction. Fe acted a liquid catalyst at growth condition. Grown SiC nanorod has about 30nm diameter and $5{\mu}m$ length. SiC nanorod growth was divided by trro regions with diameter distribution. This diameter distribution were occurred by surface deposition at as - grown nanorod's surface by limitation of growth rate. At higher temperature, these division not occurred. Growth temperature and flow rates affected diameter and morphology of nanorods. With increasing flow rate of source gas, nanorod's diameter increased because of deactivation effect. Case of the increasing temperature, growth rate increased so deactivation did not occurred.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 E
• /
• pp.1657-1659
• /
• 1997

Electron temperature and electron density were measured in a radio-frequency inductively coupled plasma (RFICP) using a probe measurements. Measurement was conducted in an argon discharge for pressures from 10 [mTorr] to 40 [mTorr] and input rf power from 100 [W] to 800 [W], Ar flow rate from 5 [sccm] to 30 [sccm], Spatial distribution electron temperature and electron density were measured for discharge with same aspect ratio (R/L=2). Electron temperature and electron density were discovered depending on both pressure and power, Ar flow rate. Electron density was increased with increasing input power and in creasing pressure, increasing Ar flow rate. Radial distribution of the electron density was peaked in the plasma center. Normal distribution of the electron density was peaked in the center between quartz plate and substrate. From these results, We found out the generation mechanism of Radio-Frequency Inductively Coupled Plasma.

• 한국잠사곤충학회지
• /
• 제35권1호
• /
• pp.48-51
• /
• 1993

견의 저온염색용 조제(K-1)를 사용하여 염색시간, 염색온도, 조제의 농도에 따른 염색속도를 구하여 이 조제가 산성 metal complex 염료의 저온염색 특성에 미치는 영향을 분석한 결과를 용약하면 다음과 같다. 1. 조제 첨가구가 무첨가구보다 높은 흡진율을 보였으며, 조제의 농도가 증가할수록 흡진율도 증가하였다. 2. 조제의 농도가 3% o.w.f. 이상에서는 망초 50% o.w.f. 첨가보다 높은 흡진율을 보였다. 3. 염료농도가 증가할수록 흡진율을 감소하였으나 조제 첨가구에서의 감소율은 적게 나타났다. 4. 승온 염색한 결과 조제의 첨가구는 높은 흡진율을 보였으나 무첨가구는 낮은 흡진율을 나타내었다.

• 대한기계학회논문집B
• /
• 제21권3호
• /
• pp.358-370
• /
• 1997

In the present study, investigations were carried out to obtain data on combustion characteristics of methane gas and hydrogen supplemented methane gas in a constant volume combustion chamber. The main results obtained from the study can be summarized as follows. The maximum combustion pressure increases as the initial pressure and hydrogen supplement rate increase, the total burning time is shorten by lowering the initial pressure and by increasing the hydrogen supplement rate. The maximum flame temperature and NO concentration increase by the initial pressure and hydrogen supplement rate increase. The flame propagation processes in near stoichiometric mixture are propagated with a spherical shape, but in excess rich or lean mixtures are propagated with a elliptical shape. And, they are changed an unstable elliptical shape flame with very regular cells by increasing the hydrogen supplement rate.

• The Korean Journal of Ceramics
• /
• 제5권2호
• /
• pp.155-161
• /
• 1999

The tribological behaviour of monolithic SiC as well as SiC-TiC and SiC-TiC-$TiB_2$ particulate composite materials has been investigated in unlubricated oscillating sliding tests against $Al_2O_3$ at temperature in the range from room temperature up to $600^{\circ}C$. At temperatures below $600^{\circ}C$ the wear rate of the systems with the composite materials was up to 20 times lower than the wear of the $Al_2O_3$/SiC system and was dominated by the oxidation of the titanium phases. At $600^{\circ}C$ the oxidation rate of the TiC and -TEX>$TiB_2$ grains becomes predominant resulting in an enhanced wear rate of the composite rate of the TiC and TiB2 grains becomes predominant resulting in an enhanced wear rate of the composite materials. The coefficient of friction shows similar values for all materials of investigation, increasing from 0.25…0.3 at room temperature to 0.7…0.8 $600^{\circ}C$. The wear of the $Al_2O_3$/SiC system is mainly abrasive at temperatures above room temperature and is characterised by an enhanced wear of the alumina ball at $600^{\circ}C$.

• 소성∙가공
• /
• 제4권2호
• /
• pp.159-168
• /
• 1995

The torsion tests in the range of $550~800^{\circ}C$, $5.0{\times}10^{-3}~5.0{\times}10^0/sec$ were performed to study the effects of strain rate$(\.{\varepsilon})$ and temperature(T) on the hot strength of Cu-Zn alloy. High temperature flow stresses of this alloy increased with increasing $\.{\varepsilon}$ and/or decreasing T, and than the more grain refinement could be obtained. The flow curves exhibited a peak followed by a steady steady state regime as a result of dynamic recrystallization. The hot strength dependence of $\.{\varepsilon}$ and T was described by a hyperbolic sine law, $\.{\varepsilon}=A(sinh0.017{\sigma})^4.81$exp(-216KJ/mol). Hot strength could be reduced at the arbitary condition, $\.{\varepsilon}$ and T, by constitutive parameter Z(Zenner-Hollomon parameter), $Z=A(sinh{\alpha}{\sigma})^n=\.{\varepsilon}$exp(Q/RT).

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.III
• /
• pp.632-638
• /
• 2000

This paper represents the characteristics of evapotranspiration rate (EVTR) and graft-taking of watermelon grafted seedlings in a graft-taking enhancement system using fluorescent lamps as artificial lighting source. Four air temperature levels of 23, 25, 27 and 29C, three humidity levels of 85, 90 and 95%R.H. and two photosynthetic photon flux (PPF) levels of 30 and 50 ${\mu}$mol m$\^$-2/ S$\^$-1/ were provided to investigate the effects of air temperature, relative humidity and light intensity on EVTR and graft-taking of grafted seedlings. EVTR of grafted seedlings increased with increasing air temperature and the passage of time after grafting. Also EVTR increased with decreasing relative humidity. As relative humidity decreased and air temperature increased, vapor pressure deficit increased and thus EVTR increased. It is required to maintain a low level vapor pressure deficit for suppressing EVTR of grafted seedlings during first 1-2 days after grafting. Therefore, less EVTR at initial stage after grafting would be adequate for smooth joining of the scion and rootstock.

• 한국세라믹학회지
• /
• 제21권2호
• /
• pp.156-164
• /
• 1984

The characteristic of pyrolytic carbon deposited in a fluidized bed as measured by density apparent crystallite size and viewed metallographically under polarized light can be easily controlled by adjusting the deposition parameters such as deposition temperature and propane flow rate or silicon content. The density of isotopic pyrolytic carbons deposited from propane between 120$0^{\circ}C$ and 140$0^{\circ}C$ increases with increasing propane flow rate and decreasing deposition temperature from 1, 73g/cc to 2.08g/cc. The apparent crystallite size Lc parameter appears to depend only on deposition temperature being entirely independent of the propane flow rate. The carbon matrix density of the silicon-alloyed carbonds deposited from propane and methyltrichlorosil-ane from 2.05g/cc for a silicon content around 9wt% to 2.67g/cc for a silicon content of 36.7wt% The Lc parameter of the deposition temperature being entirely independent of the silicon content.

• 한국표면공학회지
• /
• 제19권3호
• /
• pp.109-120
• /
• 1986

The electroless nickel plating on high alumina ceramics was performed in the bath containing nickel chloride, sodium hypophosphite and mono- or bi-carboxylic acid as a complexing agent in order to examine the empirical rate law as well as the effects of the complexing agent, plating temperature and pH on the rate of deposition. Adding the carboxylic acid to the plating bath, the rate of deposition was increased considerably, and each of the complexing agents showed a maximum deposition rate plateau around a particular concentration of the complexing agent. The rate of deposition was increased with increasing either temperature or pH, but microstructure of the surface became more rough. Furthermore, empirical rate law of the elecltroless nickel deposition on high alumina ceramics was discussed with the activation energy and other rate parameters calculated.