• Journal of Ocean Engineering and Technology
• /
• v.1 no.1
• /
• pp.111-119
• /
• 1987

The corrosion fatigue crack propagation characteristics of SS41 steel in 3.5% NaCl solution have been evaluated for loading frequencies of 1Hz and 0.2Hz. A sine wave loading profile was used for fatigue testing. Each test was carried out at a constant stress ratio, R(0.1). The main results are summarized as follows; 1. Fatigue crack propagation rate was higher in 3.5% NaCl solution than in air, higher in the base metal than in the weld metal, and higher at f =0.2Hz than at f =1Hz. 2. The crack closure level of the base metal was not influenced by cyclic frequencies, but that of the weld metal was much influenced. 3. When the crack closure effect was eliminated in the evaluation of crack propagation characteristics by using $\Delta K_{eff}$, the envirommental influence was distinctly observed. At the base metal, crack propagation rate was enhanced by the hydrogen embrittlement, and the weld metal was reduced by the crac closure. 4. There was clearly observed hydrogen embrittlement and severely corroded aspect at fracture surface of lower frequency than that of higher frequency, and at that of base metal than that of the weld metal.

• Journal of Korean Institute of Industrial Engineers
• /
• v.34 no.1
• /
• pp.108-121
• /
• 2008

Dispatching rule for parallel machines with multi product is proposed in this paper, In current market,customer's request for higher quality is increasing, In accordance with such demand, manufacturers are focusingon improving the quality of the products. Such shift in production objective is risky. The possibility ofneglecting another important factor in customer satisfaction increases, namely due dates. From the aspect ofimproving quality, frequency of product assignment to limited number of high performance machines willincrease. This will lead to increased waiting time which can incur delays, In the case of due date orientedproduct dispatch, Products are assigned to machines without consideration for quality. Overall deterioration ofproduct quality is inevitable, In addition, Poor products will undergo rework process which can increase delays.The objective of this research is dispatching products to minimize due date delays while improving overallquality. Quality index is introduced to provide means of standardizing product quality. The index is used toassure predetermined quality level while minimizing product delays when dispatching products. Qualitystandardization method and dispatching algorithm is presented. And performance evaluation is performed withcomparison to various dispatching methods.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.10a
• /
• pp.574-584
• /
• 2006

Bi-directional loading test data are available to evaluate the design parameters which reflect the characteristics of a construction method and the variations of ground at the site where drilled shafts are installed. The method to obtain the design parameters of a real bridge by hi-directional loading test was introduced. The plans of multi-level testing and installation of measuring instruments should be made according to the rough estimation of axial bearing capacity, the length of pile, and the construction method. While the relationship between end bearing resistance and displacement was obtained directly from the hi-directional loading test, the relationship between unit side resistance and displacement was calculated through the measuring values. 1% displacement of pile diameter was adopted as the criteria of failure for ultimate resistance. As the settlement of pile head at the total ultimate bearing capacity obtained from these method was less than 1.5 % of pile diameter, this method was conservative to use in the field.

• Journal of Information Processing Systems
• /
• v.5 no.4
• /
• pp.175-186
• /
• 2009

Power consumed by modern computer systems, particularly servers in data centers has almost reached an unacceptable level. However, their energy consumption is often not justifiable when their utilization is considered; that is, they tend to consume more energy than needed for their computing related jobs. Task scheduling in distributed computing systems (DCSs) can play a crucial role in increasing utilization; this will lead to the reduction in energy consumption. In this paper, we address the problem of scheduling precedence-constrained parallel applications in DCSs, and present two energy- conscious scheduling algorithms. Our scheduling algorithms adopt dynamic voltage and frequency scaling (DVFS) to minimize energy consumption. DVFS, as an efficient power management technology, has been increasingly integrated into many recent commodity processors. DVFS enables these processors to operate with different voltage supply levels at the expense of sacrificing clock frequencies. In the context of scheduling, this multiple voltage facility implies that there is a trade-off between the quality of schedules and energy consumption. Our algorithms effectively balance these two performance goals using a novel objective function and its variant, which take into account both goals; this claim is verified by the results obtained from our extensive comparative evaluation study.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.588-591
• /
• 2009

Ground source heat pump system; GSHPs is close to most practical use for early stage investment cost and energy efficiency in new renewable energies, and currently considered utilizing to the heat and cooling system of a building. Particularly, the case to utilize 'Standing Column well heat source gathering method' in the open standards process to have the excellent capability of gathering geothermal source is increased. But the research for the optimal design technology and the assessment of a pollution level of the ground to utilize a single well for gathering geothermal is insignificant and the design is insufficient. The heating and cooling system and the equipment to utilize a large size residential development to have over 1000 households have not developed yet. Therefore, our company developed 'geothermal hybrid system' which can construct the heat and cooling system using geothermal energy for a large size residential development of over 1000 households and conducted the evaluation of economic feasibility. Moreover we developed automatic equipment for gathering geothermal source and PLC (Programmable logic controller) to have optimal efficiency and FCU (fan coil unit) considering the floors of large size apartments.

• Tribology and Lubricants
• /
• v.21 no.2
• /
• pp.71-76
• /
• 2005

This paper compares of mechanical tensile properties of 6 kinds of copper foil. The beam lead made with copper foil. Different from other package type such as plastic package, Chip Size Package has a reliability problem in beam lead rather than solder joint in board level. A new tensile loading system was developed using voice-coil actuator. The new tensile loading system has a load cell with maximum capacity of 20 N and a non-contact position measuring system based on the principle of capacitance micrometry with 0.1nm resolution for displacement measurement. Strain was calculated from the measured displacement using FE analysis. The comparison of mechanical properties helps designer of package to choose copper for ensuring reliability of beam lead in early stage of semiconductor development.

• Journal of the Korean Society of Industry Convergence
• /
• v.23 no.3
• /
• pp.403-410
• /
• 2020

Continuous industrial development has led to a better quality of life for everyone, even further accelerating industrial growth. Industrial development, however, has also caused environmental degradation, which is posing a serious threat to humanity. It has also encouraged the indiscriminate use of limited resources, causing resource depletion. Efficient resource management based on resource circulation is critical to saving resources. Resource circulation methods are as follows: reducing the use of resources in the manufacturing process, recycling used or reprocessed products and reusing used resources without being reprocessed, remanufacturing with end-of-life products with disassembled parts. Furthermore, remanufacturing process including cleaning, inspection, repairing, and reassembling facilitate performance level as well as new typical products. It is noteworthy that the remanufacturing of machine tools can significantly save resources because their structural parts are substantially large in size. Machine tools have served as a foundation for the manufacturing industry, which has driven Korea's industrial development. Nevertheless, a few research has been reported for remanufacturing technology with used machine tools. Relevant research of developing a remanufacturing process chart and method is prerequisite for saving the resource and environments.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.307-310
• /
• 2005

This Study was performed for the Insensitive Munition Technology Program contract between Roxel and ADD. Two Slow Coo-off(SCO) tests and One fast Cook-off(FCO) test have been made based on MIL-STD-2105C. SCO and FCO tests were made in order to evaluate the behaviour of the hybrid rocker motor with insensitive igniter and two types of propellants of which burning rates were 9.8 mm/s and 21.2 mm/s @ 7 MPa each other. The Reaction level of the two rocker motors to SCO test was classified as type IV and that of FCO test was classified as type V.

• Journal of Distribution Science
• /
• v.18 no.6
• /
• pp.93-101
• /
• 2020

Purpose: While crowdfunding functions as a purchasing behavior, it is different from other purchasing behavior. It derives from non-existed idea and leads to production and purchase through continuous idea development with participants and participants' support is a proxy for future sales. This study researches on consumption value, customer's trust and consumer's innovativeness to reveal which constructs of consumption value and customer's trust should be considered. Research design, data, and methodology: Crowdfunding participation intentions were examined using consumer's consumption value and trust of platforms as independent variables, and consumer innovation as a control variable. A total of 175 surveys were used for analysis. The hypothesis was tested using hierarchical regression analysis. Results: The results showed economic, epistemic value and ability, benevolence consumer trust to have a significant effect in crowdfunding participation intentions. The moderating effect of innovation was shown to be significant in only economic value and benevolence. Conclusions: The economic and hedonic value of consumers should be emphasized, as well as the evaluation level of the project itself. Moreover, technology or system safety, competency, and product specific information, as well as user benefits for their ideas are core elements in attracting new participants.

• Journal of Information Technology Services
• /
• v.19 no.5
• /
• pp.125-136
• /
• 2020

The subject of this study is user experience analysis for OTT mobile app services. Application service quality was quantitatively measured by utilizing KS-eSQI evaluation model from a service quality perspective. The purpose of this analysis is to analyze how service reuse and other people's intention to recommend services are affected by service quality. In addition, further analysis of user experience will qualitatively look at what efforts are needed to improve OTT service quality and provide a user-friendly environment. According to the survey, the higher the level of KS-eSQI service quality, the higher the reuse of OTT services and recommendation of others. In particular, the dimensions of primary services and unexpected additional services had a higher impact on customer loyalty and recommendation of others than in other industries. Moreover, the following three implications were found to improve app services from a customer experience perspective. First, images and video thumbnails that highlight the strength of the content they provide should be actively utilized. Second, it is necessary to provide service companies with evidence for data-based work recommendations. Third, it should provide a viewing environment in which users can respond more intelligently to the various situations and conditions when they actually watch.