• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.5
• /
• pp.675-681
• /
• 2016

A 41dB gain control range $6^{th}$-order band-pass receiver front-end (RFE) using CMOS switched frequency translated impedance (FTI) is presented in a 40 nm CMOS technology. The RFE consists of a frequency tunable RF band-pass filter (BPF), IQ gm cells, and IQ TIAs. The RF BPF has wide gain control range preserving constant filter Q and pass band flatness due to proposed pre-distortion scheme. Also, the RF filter using CMOS switches in FTI blocks shows low clock leakage to signal nodes, and results in low common mode noise and stable operation. The baseband IQ signals are generated by combining baseband Gm cells which receives 8-phase signal outputs down-converted at last stage of FTIs in the RF BPF. The measured results of the RFE show 36.4 dB gain and 6.3 dB NF at maximum gain mode. The pass-band IIP3 and out-band IIP3@20 MHz offset are -10 dBm and +12.6 dBm at maximum gain mode, and +14 dBm and +20.5 dBm at minimum gain mode, respectively. With a 1.2 V power supply, the current consumption of the overall RFE is 40 mA at 500 MHz carrier frequency.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.1129-1132
• /
• 2002

In this paper we analyze a class of switched mode DC-DC converters and derive some topological conditions for the circuit to work as DC-DC converter, in particular, buck, booster, and buch/booster cponverters.

• Journal of Advanced Marine Engineering and Technology
• /
• v.21 no.3
• /
• pp.278-283
• /
• 1997

The rectifier is the main element in the telecom DC power system. This paper investigates the advantages and disadvantages of three rectifier techniques ; thyristor, ferro - resonant, and switched - mode. Compared with other techniques, the switched - mode rectifier tech¬nique offers several advantages such as higher efficiency, smaller size and weight, and lower audible noise. Technical requirements in telecom rectifier plant are also described. Finally, the future trends in telecom powering are discussed in connection with the advance oftelecom net¬works.

• Proceedings of the Optical Society of Korea Conference
• /
• 2008.02a
• /
• pp.335-336
• /
• 2008

We observe the distortion of the back scattered Stokes pulse and the complementary distortion of the transmitted pulse by the stimulated Brillouin scattering when a Q-switched Nd:YAG laser pulse injected into a single mode optical fiber. We determine the constant required energy for the SBS by comparing their temporal shapes.

• The Magazine of the IEIE
• /
• v.18 no.5
• /
• pp.1-3
• /
• 1991

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.11
• /
• pp.763-770
• /
• 2000

The speed and position information of the rotor are required in the speed control of SRM(Switched Reluctance Motors). This information is generally provided by shaft encoder or resolver. It is weak in the dusty, high temperature, and EMI environment. Consequntly, much attention has been given to SRM control for eliminationating the position and speed sensors. In this paper, a new estimation algorithm for the rotor position and speed for SRM drives is described. The algorithm is implemented by the sliding mode observer. The stability and robustness of the sliding observer for the parameter variations of the SRM are proved by variable structure control theory. Speed control of the SRM is accomplished by the estimated speed and position. Experiment results verify that the mode observer is able to estimate the speed and position well.

• International Journal of Control, Automation, and Systems
• /
• v.5 no.6
• /
• pp.707-711
• /
• 2007

An observer-based fault tolerant control (FTC) method is proposed for constrained switched systems (CSS) with input constraints. A family of Lyapunov-based bounded controllers are designed to ensure that, whenever actuator faults occur at the dwell time period of each continuous mode, the mode is always within its corresponding stability region. A set of switching laws are designed to guarantee the asymptotic stability of the overall CSS. The fixed stability regions on which the FTC method is based are also relaxed by the proposed variable stability regions. An example of CPU processing illustrates the effectiveness of proposed method.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.4
• /
• pp.505-512
• /
• 2011

A novel passive boost power converter forsingle-phaseswitched reluctance motor is presented. A simple passive circuit is proposed comprisingthree diodes and one capacitor. The passive circuitis added in the front-end of a conventional asymmetric converter to obtain high negative bias. Based on this passive network, the terminal voltage of the converter side is a general DC-link voltage level in parallel mode up to a double DC-link voltage level in series mode. Thus,it can suppress the negative torque generation from the tail current and improve the output power. The results of the comparative simulation and experiments forthe conventional and proposed converter verify the performance of the proposed converter.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.2
• /
• pp.551-559
• /
• 2015

This paper's focus is in reducing the torque ripple and increasing the average torque by optimizing switching angles of 8/6 switched reluctance motor while implementing a robust speed controller in the outer loop. The mathematical model of the machine is developed and it is simulated using MATLAB/Simulink. An objective function and constraints are formulated and Optimum turn-on and turn-off angles are determined using Particle swarm optimization and Genetic Algorithm techniques. The novelty of this paper lies in implementing sliding mode speed controller with optimized angles. The results from both the optimization techniques are then compared with initial angles with one of them clearly being the better option. Speed response is compared with PID controller.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.1219-1226
• /
• 1993

A buck-boost zero current switched(ZCS) series resonant AC to DC converter for the DC output voltage regulation together with high power factor is proposed. The proposed single phase AC to DC converter enables a zero current switching operation of all the power devices allowing the circuit to operate at high swtiching frequencies and high power levels. A dynamic model for this Ac to DC converter is developed and an analysis for the internal operational characteristics is explored. Based on this analysis, a switched discrete sliding mode control(SDSMC) technique is investigated and its advantages over the other types of current control techniques are discussed. With the proposed control technique, the unity power factor without a current overshoot and a wide range of output voltage can be obtained.