• Journal of the Korean earth science society
• /
• v.35 no.7
• /
• pp.554-561
• /
• 2014

The rock materials from the two stone heritages in the Seonbonsa temple, Gwanbong Seokjoyeoraejwasang (stone Buddha) and three-storied Stone Pagoda, show almost identical petrographic characteristics. They are greyish white porphyritic granites which mainly consist of plagioclase, alkali feldspar, quartz, biotite, hornblende, and chlorite. The rocks from the both heritages are petrographically similar to those from the outcrops of the Palgongsan granite near the temple. Modal compositions exhibit that the rocks from the stone Buddha belong to monzogranite, whereas those from the pagoda and the outcrop near the temple correspond to syeno- to monzo granite. Whole rock magnetic susceptibility data indicate that the rocks from the stone Buddha, the pagoda, and the outcrop have nearly the same susceptibility values ranging 9-16(${\times}10^{-3}\;SI$). Gamma spectrometer data obtained from these rocks also demonstrate the same value range. In conclusion the two stone heritages in the Seonbonsa temple were made of the Palgongsan granite surrounding the temple.

• The Journal of Engineering Geology
• /
• v.24 no.3
• /
• pp.397-409
• /
• 2014

The appearance of faults during tunnel construction is often difficult to predict in terms of strike, dip, scale, and strength, even though this information is essential in determining the strength of the surrounding rock mass. However, the strength and rock mass classification of fault zones are generally determined empirically on the construction site. In this study, 109 specimens were collected from fault of nine area throughout Korea, and direct shear tests were conducted and the particle distribution was analyzed to better characterize the fault zones. Six multiple regression models were established, using 97 of the specimens, to analyze the correlation between the shear strengths and weight rations of these fault materials. A verification of the six models, using the remaining 12 specimens, shows that in all of the models the coefficient of determination yielded $R^2{\geq}0.60$, with two models yielding $R^2{\geq}0.69$. These results provide useful information for determining the shear strength of fault materials in future studies.

• Tunnel and Underground Space
• /
• v.16 no.1 s.60
• /
• pp.73-84
• /
• 2006

Effects of railway tunnel excavation on water level at a national groundwater monitoring station in Mokpo were evaluated by field investigation and numerical groundwater modeling. The water level at the station has experienced a decline of about 5 m within 1 year since July 2002. From the field investigation, it was concluded that decrease of precipitation oo increase of grundwater use was not reason for the decline. The Mokpo tunnel of new Honam railway, 70 m apart from the national station, appeared most plausible cause and a period of the tunnel excavation generally well matches up that of the drawdown. To quantify the effects of the tunneling on the water level, a groundwater flow modeling was performed. Especially, a most probable conceptual model was optimized through multiple preliminary simulations of various scenarios because there were few hydrogeological data available for the study area. The optimized model was finally used for the quantification. Based on the field investigation and the numerical simulations, it was concluded that the tunnel excavation was one of the most probable reasons for the substantial water level decline but further hydrogeologic investigation and continuous monitoring are essentially required for the surrounding area.

• Tunnel and Underground Space
• /
• v.19 no.3
• /
• pp.248-260
• /
• 2009

With regard to oversea mineral resources development, recent trend has been changed from a simple capital investment to a direct development of the resources. In relation to the stability of a slope in large open-pit coal mine, groundwater system was investigated and the validity of horizontal drainage hole was evaluated in Pasir coal mine, Indonesia. In this work, various field tests were carried out for a characterization of groundwater system, which included in-situ permeability measurement, tracer test and monitoring of groundwater levels. Especially, the influence of SM river on the characteristics of the groundwater flow system was mainly inspected. For the permeability measurement, Guelph permeameter was employed, and was found that sandstone was more permeable than mudstone and coal seam. From a comparison of lithological structure and the results of groundwater level monitoring, sandstone and thin coal seam with fractures were found to be a main channel for groundwater flow. In the results of tracer tests, the effect of SM river on the groundwater system depends on the geological structure of its base. To identify the effect of horizontal drainage holes, 2-D groundwater modeling was performed. Four different cases were tested, which are different from the length of drainage hole and the existence of pond on top of the slope. To enhance the drainage effect and slope stability, the drainage hole should be drilled to the depth of coal seam layer, which provides a main pathway of groundwater flow and embedded by sandstone. For this purpose, correct identification of surrounding geology should be preceded.

• The Journal of Engineering Geology
• /
• v.20 no.2
• /
• pp.121-126
• /
• 2010

Current technology for radioactive waste disposal facility is operated as part of KURT site characterization in terms of reliability assessment is conducted to expand. In this study, a geological model of KURT surrounding area on the basis of flow characteristics of the site-scale hydrogeological study was about. Distributed in the study area into four boreholes were plotted using the stereo net NS, NW, EW, Low-angle fracture group was able to identify the components of geological models and include top soil layer, belt of weathering, Low-angle fracture zone, fracture zone was divided into. Separated by fracture of the hydraulic test of through the groundwater aquifer that provides the flow hydraulic conductivity and insulation hydraulic affecting the slope of the normal distribution for the size and direction by performing statistical analysis of fracture in the direction of local ns The advantage was confirmed. In addition, Low-angle fracture hydraulic conductivity of the value of 3.61e-07 m/s has a value greater than the major fracture, the fracture zones exist in the base rock and base rock and the hydraulic characteristics of the different methods applied and had to have a different interpretation judged by was.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.16 no.3
• /
• pp.339-346
• /
• 2018

A geological repository system consists of a disposal canister with packed spent fuel, buffer material, backfill material, and intact rock. The buffer is indispensable to assure the disposal safety of high-level radioactive waste. Since the heat generated from spent nuclear fuel in a disposal canister is released to the surrounding buffer materials, the thermal properties of the buffer material are very important in determining the entire disposal safety. Especially, since thermal expansion can cause thermal stress to the intact rock mass in the near-field, it is very important to evaluate thermal expansion characteristics of bentonite buffer materials. Therefore, this paper presents a thermal expansion coefficient prediction model of the Gyeongju bentonite buffer materials which is a Ca-bentonite produced in South Korea. The linear thermal expansion coefficient was measured considering heating rate, dry density and temperature variation using dilatometer equipment. Thermal expansion coefficient values of the Gyeongju bentonite buffer materials were $4.0{\sim}6.0{\times}10^{-6}/^{\circ}C$. Based on the experimental results, a non-linear regression model to predict the thermal expansion coefficient was suggested and fitted according to the dry density.

• Economic and Environmental Geology
• /
• v.32 no.5
• /
• pp.469-483
• /
• 1999

Two different types of deep groundwaters occur together in the Jungwon area: $CO_2$-rich water and alkali water. Each water shows distrinct hydrogeochemical and environmental isotopic characteristics. The $CO_2$-rich waters are characterized by lower pH(6.0~6.4), higher Eh (25~85mV) and higher TDS content (up to 3,300 mg/l), whereas the alkali type waters have higher pH (9.1~9.5), lower Eh (-136~-128mV) and lower TDS content (168~254 mg/l). The CO2-rich waters ($Pco_2$=up to 1atm) were probably evolved by the local supply of deep $CO_2$ during the deep circulation, resulting in enhanced dissolution of surrounding rocks to yield high concentrations of $Ca^{2+}, Na^+, Mg^{2+}, K^+\; and \;HCO_3\;^-$ under low pH conditions. On the other hand, the alkali type waters ($Pco_2$=about 10-4.6 atm) were evolved through lesser degrees of simple wate/rock (granite) interaction under the limited suppy of $CO_2$. The alkali waters are relatively enriched in F- (up to 14mg/l), whereas the F- concentration of$CO_2$-rich water is lower (2.2~4.8 mg/l) due to the buffering by precipitation of fluorite. The oxygen-hydrogen isotopes and tritium data indicate that compared to shaltion ($\delta$18O=-9.5~-7.8$\textperthousand$),two different types fo deep groudwaters (<1.0TU)were both derived from pre-thermonuclear (more than 40 years old) meteoric waters with lighter O-H isotopic composition ($\delta$18O=-9.5~-7.8$\textperthousand$) and have evolved through prolonged water/rock interaction. The $CO_2$-rich waters also show some degrees of isotopic re-equilibration with $CO_2$ gas. The $\delta^{34}S$ values of dissolved sulfates (+24.2~+27.6$\textperthousand$) in the $CO_2$-rich waters suggest the reduction of sulfate by organic activity at depths. The carbon isotope data show that dissolved carbon in the $CO_2$-rich waters were possibly derived either from dissolution of calcite or from deep $CO_2$ gas. However, strontium isotope data indicate Ca in the $CO_2$-rich waters were derived mainly from plagioclase in granite, not from hydrothermal calcites.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.9 no.2
• /
• pp.171-182
• /
• 2007

For minimizing the effect on the focus of civil traffic and environment conditions related to the excavation at the traffic jamming points, an underground station tunnel was planned with 35.5 m in length and bigger area than $200\;m^2$ in sedimentary rock mass. It faced the case that the overburden was just under 13 m. Not based on a pattern design but on the case histories of similar projects and arching effect, the design of large section tunnel under shallow overburden was investigated on three design subjects which are shape effect on the section area, application method of support pressure, and supporting and tunnel safety. According to the mechanical effect from section shape, a basic design and a preliminary design was obtained, and then supporting method of large section was planned by the supporting of NATM and a pipe roof method for subsidence prevention and mechanical stability. From the comparative study between both designs, it was found that the basic design was suitable and acceptable for the steel alignment of tunnel lining, safety and the design parameter restricted by the limit considered as partition of the excavation facilities. Through the analysis result of preliminary design showing the mechanical stability without stress concentration in tunnel arch level, it also was induced that shape effect of the large section area and yielding load obtained from deformation zone in the surrounding rock mass of tunnel have to be considered as major topics for the further development of design technique on the large section tunnel.

• Tunnel and Underground Space
• /
• v.21 no.6
• /
• pp.518-525
• /
• 2011

In this study, the natural ventilation pressure resulting from the large altitude difference which is a characteristic of high radioactive waste repository and the caloric value of the heat emitted by wastes was calculated and based on the results, natural ventilation quantities were calculated. A high radioactive waste repository can be considered as being operated through closed cycle thermodynamic processes similar to those of thermal engines. The heat produced by the heating of high radioactive wastes in the underground repository is added to the surrounding air, and the air goes up through the upcast vertical shaft due to the added heat while working on its surroundings. Part of the heat added by the work done by the air can be temporarily changed into mechanical energy to promote the air flow. Therefore, if a sustained and powerful heat source exists in the repository, the heat source will naturally enable continued cyclic flows of air. Based on this assumption, the quantity of natural ventilation made during the disposal of high radioactive wastes in a deep geological layer was mathematically calculated and based on the results, natural ventilation pressure of $74{\sim}183$Pa made by the stack effect was identified along with the resultant natural ventilation quantity of $92.5{\sim}147.7m^3/s$. The result of an analysis by CFD was $82{\sim}143m^3/s$ which was very similar to the results obtained by the mathematical method.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.15 no.3
• /
• pp.199-206
• /
• 2017

A geological repository for the disposal of high-level radioactive waste is generally constructed in host rock at depths of 500~1,000 meters below the ground surface. A geological repository system consists of a disposal canister with packed spent fuel, buffer material, backfill material, and intact rock. The buffer is indispensable to assure the disposal safety of high-level radioactive waste, and it can restrain the release of radionuclides and protect the canister from the inflow of groundwater. Since high temperature in a disposal canister is released to the surrounding buffer material, the thermal properties of the buffer material are very important in determining the entire disposal safety. Even though there have been many studies on thermal conductivity, there have been only few studies that have investigates the specific heat capacity of the bentonite buffer. Therefore, this paper presents a specific heat capacity prediction model for compacted Gyeongju bentonite buffer material, which is a Ca-bentonite produced in Korea. Specific heat capacity of the compacted bentonite buffer was measured using a dual probe method according to various degrees of saturation and dry density. A regression model to predict the specific heat capacity of the compacted bentonite buffer was suggested and fitted using 33 sets of data obtained by the dual probe method.