• 대한기계학회논문집A
• /
• 제32권3호
• /
• pp.250-257
• /
• 2008

We calculate the variation of the surface stresses according to uniaxial and biaxial strains in face-centered cubic (FCC) metals. In our study, three mainly observed free surfaces of seven representative FCC metals are considered. Employed method is molecular mechanics, in which the interaction of atoms is described by empirical interatomic potentials. As uniaxial strain increases to tensile direction, the surface stresses on {100} and {110} free surfaces decrease monotonously, while those on {111} surface increase. These tendencies are the same regardless of the species of metals and interatomic potentials employed. However, when the system is under biaxial strain, surface stresses change different according to the surface directions, the species of metals, and even interatomic potentials. On {100} and {111} surfaces, heavy metals (Pt, Au) show the opposite variation to light metals (Ni, Cu). In the cases of Pd and Ag, the surface stresses reveal the opposite tendency, depending on interatomic potentials used.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.308-312
• /
• 2003

The packaging of the integrated circuits requires knowledge of ceramics and metals to accommodate the fabrication of modules that are used to construct subsystems and entire systems from extremely small components. Composite ceramics ($Al_2O_3-SiO_2$) were tested for substrates. A stress analysis was conducted for a linear work-hardening metal cylinder embedded in an infinite ceramic matrix. The bond between the metal and ceramic was established at high temperature and stresses developed during cooling to room temperature. The calculations showed that the stresses depend on the mismatch in thermal expansion, the elastic properties, and the yield strength and work hardening rate of the metal. Experimental measurements of the surface stresses have also been made on a $Cu/Al_2O_3-SiO_2$ ceramic system, using an indentation technique. A comparison revealed that the calculated stresses were appreciably larger than the measured surface stresses, indicating an important difference between the bulk and surface residual stresses. However, it was also shown that porosity in the metal could plastically expand and permit substantial dilatational relaxation of the residual stresses. Conversely it was noted that pore clusters were capable of initiating ductile rupture, by means of a plastic instability, in the presence of appreciable tri-axiality. The role of ceramics for packaging of microelectronics will continue to be extremely challenging.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.566-567
• /
• 2006

The characteristics of residual stresses occurring in PM steel based nickel (FLN2-4405) was investigated. The measurements of residual stresses were carried out by electrochemical layer removal technique. The values and distributions of residual stresses occurring in PM steel processed under various densities and heat treatment conditions were determined. In most of the experiments, tensile residual stresses were recorded in surface of samples. The residual stress distribution on the surface of the PM steels is affected by the heat treatment conditions and density. Maximum values of residual stresses on the surface were observed sinter hardened condition and $7.4\;g/cm^3$ density. Minimum level of recorded tensile residual stresses are150 MPa and its maximum level is 370 MPa.

• 한국정밀공학회지
• /
• 제20권5호
• /
• pp.148-155
• /
• 2003

Most manufacturing processes such as welding, cutting and molding generate residual stresses on the surface of manufactured parts. Between compressive and tensile residual stresses, the tensile residual stress is harmful to the surface integrity, which results in reduced fatigue life and causes other structural failures when the service stresses are superimposed on the residual stresses. In the research, the residual stresses in the hardened tool steel (SKD11) were measured using hole-drilling method. The specimens were prepared through hard turning. Most of residual stresses in the machined surface were compressive.

• 한국표면공학회지
• /
• 제17권3호
• /
• pp.73-77
• /
• 1984

The surface residual stresses in 1mm thick nickel electrodeposits obtained from four types of nickel sulphamate baths at 40 to 60$^{\circ}C$ and 5 to 25 amps./$dm^2$ were measured by a X-ray method. An increase in nickel chloride concentration in the bath tends to increase tensile residual stresses in the deposits. Addition of no chloride or little chloride in the baths gave rise to little residual stresses or even compressive stresses in the deposits. The residual stresses in most specimens did not exceed 80 MPa and showed minimum in the specimens obtained at 50$^{\circ}C$.

• Structural Engineering and Mechanics
• /
• 제82권2호
• /
• pp.259-270
• /
• 2022

The paper investigates the residual stresses arising in a thermoviscoelastic cylinder as a result of layer-by-layer deposition of material on its lateral surface. Internal stresses are caused by incompatible deformations that accumulate in the assembly as a result of joining parts with different temperatures. For the analysis of internal stresses, an analytical solution to the axisymmetric quasi-static problem of thermoelasticity for a growing cylinder is constructed. It is shown that the distribution of residual stresses depends on the scenario of the surfacing process. In this case, the supply of additional heat to the growing body can significantly reduce the unevenness of temperature fields and reduce the intensity of residual stresses. The most effective is uneven heating, which can be realized, by the action of an alternating current with a tunable excitation frequency. The temperature and residual stresses fields on the growing surface is analyzed numerically for Titanium and Copper materials.

• 소성∙가공
• /
• 제19권4호
• /
• pp.224-229
• /
• 2010

During the multi-pass wire drawing process, wires suffer a great amount of plastic deformation that is through the cross-section. This generates tensile residual stress at surface of drawn wires. The generated residual stress on surface is one of the problems for quality of wires so that prediction and reduction of residual stresses is important to avoid unexpected fracture. Therefore, in this study, the effect of process variables such as semi-die angle, bearing length and reduction ratio on the residual stress was evaluated through Finite Element Analysis. Based on the results of the Analysis, a prediction model was established for predicting residual stress on the surface of high carbon steel(AISI1072, AISI1082). To identify the effectiveness of the proposed model, X-ray diffraction is used to measure the residual stresses on the surface. As the result of the comparison between calculated residual stresses and measured residual stresses, the model could be used to predict residual stresses in cold drawn wire.

• 소성∙가공
• /
• 제21권1호
• /
• pp.58-66
• /
• 2012

The work roll surface temperature rises and falls repetitively during hot slab rolling because the work roll surface is cooled continuously by water. This study focused on Std. No. 7 to determine a cooling method which significantly reduces the tangential tensile stresses on the work roll surface of the hot slab mill at Hyundai Steel Co. in Korea. A series of finite element analyses were performed to compute the temperature distribution and the tensile stresses in the circumferential direction of the work roll. The virtual slab model was used to reduce the run time considerably by assigning a high temperature to the virtual slab. Except for the heat generated by plastic deformation, this is equivalent to the hot rolling condition that a high temperature slab (material) would experience when in contact with the work rolls. Results showed that when the virtual slab model was coupled with FE analysis, the run time was found to be reduced from 2000 hours to 70 hours. When the work roll surface cooled with a certain on-off patter of water spray, the magnitude of the tangential stresses on the work rolls were decreased by 54.1%, in comparison with those cooled by continuous water spraying. Savings of up to 83.3% in water usage are possible if the proposed water cooling method is adopted.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2004년도 SMICS 2004 International Symposium on Maritime and Communication Sciences
• /
• pp.70-73
• /
• 2004

The packaging of the integrated circuits requires knowledge of ceramics and metals to accommodate the fabrication of modules that are used to construct subsystems and entire systems from extremely small components. Composite ceramics (Al$_2$O$_3$-SiO$_2$) were tested for substrates. A stress analysis was conducted for a linear work-hardening metal cylinder embedded in an infinite ceramic matrix. The bond between the metal and ceramic was established at high temperature and stresses developed during cooling to room temperature. The calculations showed that the stresses depend on the mismatch in thermal expansion, the elastic properties, and the yield strength and work hardening rate of the metal. Experimental measurements of the surface stresses have also been made on a Cu/Al$_2$O$_3$-SiO$_2$ceramic system, using an indentation technique. A comparison revealed that the calculated stresses were appreciably larger than the measured surface stresses, indicating an important difference between the bulk and surface residual stresses. However, it was also shown that porosity in the metal could plastically expand and permit substantial dilatational relaxation of the residual stresses. Conversely it was noted that pore clusters were capable of initiating ductile rupture, by means of a plastic instability, in the presence of appreciable tri-axiality. The role of ceramics for packaging of microelectronics will continue to be extremely challenging.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.331-332
• /
• 2002

Most manufacturing processes such as welding, cutting and molding generate residual stresses on the surface of manufactured parts. Tensile residual stress is harmful to the surface integrity, which results in reduced fatigue life and causes other structural failures when the service stresses are superimposed on the residual stresses. In the research, the residual stresses of the high hardness steel (over $H_{RC}60$) workpiece (SKD11) machined by the hard turning were measured using Hole-drilling Method. Residual stress in the surface of hard turned workpiece was mainly appeared to be compressive stress.