• Transactions of the Korean hydrogen and new energy society
• /
• v.17 no.1
• /
• pp.47-54
• /
• 2006

Activated carbon fibers (ACFs) with high surface area and pore volume were modified with metal Ni impregnation and fluorination and investigated hydrogen storage properties by volumetric method. Micropore volume values of ACFs obtained from surface modification with Ni impregnation and fluorination were decreased 9 and 35 %, respectively. Hydrogen storage capacities of fluorinated ACFs were slightly changed, on the other hand, that of Ni impregnated ACF was considerably increased. It means that hydrogen was not only adsorbed on ACF surface, but also on Ni metal surface by means of dissociation. Although the microphone volume of ACF modified with fluorination was decreased, its hydrogen storage were found not to be changed compared with fresh ACF. These results indicated that the surface of ACF after fluorination modification may be strongly attracted hydrogen due to high electronegativity of fluorine. Therefore, it was proven that hydrogen storage capacity was related with micropore volume and surface property of carbon materials as well as specific surface area.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.6
• /
• pp.1337-1340
• /
• 2009

Electrical properties of a fluorinated carbon black (CB)-filled high-density polyethylene (HDPE) polymeric switch were investigated as a function of fluorination pressure at 0.1 ~ 0.4 MPa. From the FT-IR results, the absorption spectra of the fluorinated CB show an absorption band at 1400 ~ 1000 $cm^{-1}\;for\;{\nu}_{C-F}$ and the peak intensity increased with increasing fluorination pressure. Also, the analysis of XPS spectra of the fluorinated CB indicated that fluorine content increased with increasing fluorination pressure. Meanwhile, the surface free energy of the fluorinated CB decreased with increasing fluorination pressure. Consequently, the increase of fluorine contents of CB made a disappearance of negative temperature coefficient (NTC) behavior of the polymeric switch, which was probably due to the reduction of CB reaggregation after melting point of the HDPE, resulted from the decreasing of London dispersive component of the surface free energy for CB particles.

• The Journal of Advanced Prosthodontics
• /
• v.10 no.3
• /
• pp.205-210
• /
• 2018

PURPOSE. The purpose of this study was to evaluate the efficiency of a gas-phase fluorination method under different fluorination periods through using two resin cements. MATERIALS AND METHODS. 84 zirconia specimens in dimensions of $5mm{\times}5mm{\times}2mm$ were prepared and surface treated with $50{\mu}m$ aluminum oxide particles or gas phase fluorination for 2 min, 5 min, or 10 min. One specimen in each group was surface analyzed under scanning electron microscope. The remaining specimens were bonded to composite cylinders in dimensions of 2 mm diameter and 3 mm high with Panavia SA Plus or Variolink N. Then, the specimens were stored in $37^{\circ}C$ distilled water for 24 hours and shear bond strength test was applied at a speed of 1 mm/min. RESULTS. The highest shear bond strength values were observed in the samples fluorinated for 5 minutes and cemented with Panavia SA Plus. Variolink N did not elicit any statistical differences between surface treatments. Panavia SA Plus resin cement and Variolink N resin cements featured statistically significant difference in shear bond strength values only in the case of 5 minutes of fluorination treatment. CONCLUSION. According to the results of this study, application of 5 minutes of fluorination with 10-methacryloyloxydecyl dihydrogen phosphate monomer (MDP) containing Panavia SA Plus resin cement increased the resin bond strength of zirconia. Fluorination of the zirconia surface using conventional resin cement, Variolink N, did not lead to an increase in bond strength.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.9
• /
• pp.2071-2076
• /
• 2009

The single-walled carbon nanotubes (SWCNTs) produced by chemical vapor deposition (CVD) were directly fluorinated with fluorine ($F_2$) gas in a temperature range 20 ~ 400 ${^{\circ}C}$. The surface properties and morphology of the SWCNTs were investigated in terms of fluorination temperature. As a result, Raman spectra showed a pair of bands at 1340 and 1590 $cm^{-1}$ peculiar to disordered $sp^2$-carbons. These results indicated that C-F bonds were formed on the rear surfaces of the nanotubes by fluorination, while the external surfaces as well as the layers between the internal and external surfaces retained their $sp^2$-hybridization. XPS analysis exhibited that fluorine atoms were bonded to carbon atoms on internal surfaces (rear surfaces) of the nanotubes and the amount of fluorine attached on the nanotubes was increased with increasing the fluorination temperature. Consequently, the direct fluorination of carbon nanotubes led to functionalization and modification of pristine nanotubes with respect to surface and morphological properties.

• Journal of the Korean institute of surface engineering
• /
• v.30 no.4
• /
• pp.262-271
• /
• 1997

Nickel-matal hydride(Ni-MH) batteries are receiving attention as non-pollunting. high performance rehargeable energy stoage system. The performance of Ni-Mh is significantly influenced by the hydrogen storage alloy materiels used as an anode material. Recently, having discharge capacities higher than the $AB_5$-type hydrogen storage alloys, the Zr-based $AB_2$-Type hydrogen storage alloys has remaining problems regarding cycle life and self-dischareg. These problems need to be solved by improvements in the alloy design and/or surface treatment. This work investiggates the effects the effects of surface property by fluorination on $Zr_{0.7}Ti_{0.3}V_{0.4}Mn_{0.4}Ni{1.2}$ composittion $AB_2$-Type hydrogen storage alloys. EPMA, SEM and AES techniques were used for surface analysis, and the crystal structure was characterized by constant current cycling test and potential sweep methods. Fluorination was found to be effective when La-was incorporated into the alloy, and has unique morphology, higher reactivity, and at the same time formed a protective film. Through, fluorination, the cycle life of an electrode was found to increase significantly, charge/discharge characteristics of the electrode the potential difference between the charge/discharge plateau, i.e polarization(overpotential)were improved.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.10a
• /
• pp.100-103
• /
• 2004

In this work, the effects of oxy-fluorination on surface characteristics of carbon fibers were investigated in mechanical interfacial properties of carbon fibers-reinforced composites. The surface properties of the carbon fibers were determined by X-ray photoelectron spectroscopy (XPS), FT-IR. and contact angle measurements. And their mechanical interfacial properties of the composites were studied in interlaminar shear strength (ILSS) and critical stress intensity factor $(K_{IC})$. As experimental results, the $F_{1S}/C_{1S}$ ratio of carbon fiber surfaces was increased by oxy-fluorination, due to the development of the oxygen containing functional groups. The mechanical interfacial properties of the composites, including ILSS and $K_{IC}$, had been improved in the oxy-fluorination on fibers. These results could be explained that the oxy-fluorination was resulted in the increase of the adhesion between fibers and matrix in a composite system.

• Korean Journal of Materials Research
• /
• v.9 no.6
• /
• pp.622-629
• /
• 1999

Effects of the fluorination in the $K_2$TiF\ulcorner solution and in-situ KF+ KOH electrolyte on the electrochemical charge-discharge properties of CaNi\ulcorner and the Mg-CaNi\ulcorner electrodes were investigated. In-situ fluorination in the KF+ KOH electrolyte compared with pre-fluorination in the$ K_2$TiF\ulcorner solution could improve the electrochemical cycling durability of CaNi\ulcorner and MG-CaN\ulcorner electrodes. The fluorinated layer on the alloy surface by pre-fluorination to improve the activity and anti-corrosion of the electrodes was dissolved in the pure KOH electrolyte during the cycling. The fluorinated layer was formed continuously on the surface of the electrode by thee2N KF addition in the 6N KOH electrolyte. The excess F\ulcorner ion addition in KOH electrolyte could improve the electrochemical cycling durability of CaNi\ulcorner and Mg-CaNi\ulcorner electrode. But, in case of MG-CaNi\ulcorner electrode, the discharge capacity of the electrode was reduced and the poor cycling property was shown with increasing of the MG process times.

• Journal of Powder Materials
• /
• v.30 no.1
• /
• pp.53-64
• /
• 2023

Atomic layer etching (ALE) is a promising technique with atomic-level thickness controllability and high selectivity based on self-limiting surface reactions. ALE is performed by sequential exposure of the film surface to reactants, which results in surface modification and release of volatile species. Among the various ALE methods, thermal ALE involves a thermally activated reaction by employing gas species to release the modified surface without using energetic species, such as accelerated ions and neutral beams. In this study, the basic principle and surface reaction mechanisms of thermal ALE?processes, including "fluorination-ligand exchange reaction", "conversion-etch reaction", "conversion-fluorination reaction", "oxidation-fluorination reaction", "oxidation-ligand exchange reaction", and "oxidation-conversion-fluorination reaction" are described. In addition, the reported thermal ALE processes for the removal of various oxides, metals, and nitrides are presented.

• Polymer(Korea)
• /
• v.37 no.3
• /
• pp.316-322
• /
• 2013

In this study, poly(ethylene terephthalate) (PET) was treated with fluorination and ultrasonic washing treatment for hydrophilic modification of PET film. We measured the change of surface modified PET film surface characteristics using contact angle, surface free energy, FE-SEM, AFM and XPS. After direct fluorination and ultrasonic washing treatment, the water contact angle was measured to be $10.81^{\circ}$, 85% reduction compared to the untreated PET film. Total surface free energy has been measured to be $42.25mNm^{-1}$, 650% increase compared to the untreated PET film. Also RMS roughness has been measured to be 1.965 nm, 348% increase compared to the untreated PET film. Hydrophilic functional group C-OH bond concentration has increased approximately 3 times. These results are attributed to the hydrophilic functional group and cavitation due to chemical etching. From this result, it was suggested that the fluorination-ultrasonic washing treatment method could be useful to make PET film surface hydrophilic.

• Membrane and Water Treatment
• /
• v.2 no.1
• /
• pp.39-49
• /
• 2011

We investigated about the utilization improvement of the PDMS and fluoropolymers by mutual application in environmental analysis. We were conducted the direct fluorination with mild condition on the PDMS films and analyzed its surfaces before and after fluorination. The results of FTIR and SEM analysis on the PDMS films showed that the film surfaces were fluorinated without irreversible deformation by the fluorination. During the fluorination, the measured contact angles of water and several alcohols on the PDMS films decreased with time and that of most alcohols decreased to 0 after 30 minutes. The surface energy of fluorinated PDMS films has increased by 2 times. Also, we investigated the influence factors on the change of permeation rate of water through PDMS tubes with time. It was observed that the change of permeation rate of water through PDMS tube was affected by temperature, water phase and spatial distribution of water. From these results, we could verify the principal causes of the decrease of permeation rate of water through PDMS tube with time and proposed a new experimental setup for reducing the variation of permeation rate of water less than 2%.