• Transactions on Electrical and Electronic Materials
• /
• v.14 no.3
• /
• pp.121-124
• /
• 2013

The incorporation of 90 nm alumina particles into an epoxy matrix to form a composite microstructure is described in present study. It is shown that the use of ultrafine particles results in a substantial change in the behavior of the composite, which can be traced to the mitigation of internal charges when a comparison is made with conventional $Al_2O_3$ fillers. A variety of diagnostic techniques have been used to augment pulsed electro-acoustic space charge measurement to provide a basis for understanding the underlying physics of the phenomenon. It would appear that, when the size of the inclusions becomes small enough, they act cooperatively with the host structure and cease to exhibit interfacial properties. It is postulated that the $Al_2O_3$ particles are surrounded by high charge concentrations. Since $Al_2O_3$ particles have very high specific areas, these regions allow limited charge percolation through $Al_2O_3$ filled dielectrics. The practical consequences of this have also been explored in terms of the electric strength exhibited. It would appear that there was a window in which real advantages accumulated from the nano-formulated material. An optimum filler loading of about 0.5 wt.% was indicated.

• Applied Chemistry for Engineering
• /
• v.33 no.4
• /
• pp.343-351
• /
• 2022

Lithium-ion batteries (LIBs) are considered promising energy storage devices with good performance such as high energy density, slow self-discharge rate, high rate charge capacity, and long battery life. However, the application of these LIBs in the high-energy density electric vehicle and large device industries poses a major safety problem. In order to solve this problem, developing a material having high thermal stability and intrinsic safety is the ultimate solution for improving the stability and electrochemical performance of LIBs. This review introduced a surface modification technology of a separator to overcome the stability problem of a commercial separator, and summarized and summarized the research trends using the modified separator for a lithium-ion battery. Based on this, the future prospects for the separator development by surface modification were discussed.

• Journal of Electrochemical Science and Technology
• /
• v.14 no.4
• /
• pp.311-319
• /
• 2023

This work was performed to characterize the electrochemical behavior of AZ31 Mg alloy in neutral aqueous solutions where Cl^-, SO₄^2-, PO₄^3-, and F^- ions were present and pH was adjusted to 6 to exclude the contribution of H⁺ and OH^- ions. Open-circuit potential (OCP) transient, electrochemical impedance spectroscopy (EIS) and potnetiodynamic polarization curves were employed. The OCP value appeared to decrease in the order of F^- > Cl^- > SO₄^2- > PO₄^3- ions while corrosion current density increased in the same order. Electrochemical impedance spectroscopy (EIS) data showed two capacitive arcs in all the solutions and one more inductive arc appeared in PO₄^3--containing solution. By fitting of two capacitive arcs, capacitance of dense film (C_df), resistance of porous film (R_pf) and double layer capacitance (C_dl) and charge transfer resistance (R_ct) beneath the porous films were obtained. A simplified model in which various thicknesses and coverages of dense and porous films are assumed to be present on the AZ31 Mg alloy surface, is suggested to explain the effects of four different anions on the electrochemical behavior of AZ31 Mg alloy.

• Journal of Surface Science and Engineering
• /
• v.56 no.5
• /
• pp.299-308
• /
• 2023

In this study, phosphorus (P)-doped nickel cobaltite (P-NiCo₂O₄) and nickel-cobalt layered double hydroxide (P-NiCo-LDH) were synthesized on nickel (Ni) foam as a conductive support using hydrothermal synthesis. The thermal properties, crystal structure, microscopic surface morphology, chemical distribution, electronic state of the constituent elements on the sample surface, and electrical properties of the synthesized P-NiCo₂O₄ and P-NiCo-LDH samples were analyzed using thermogravimetric analysis-differential scanning calorimetry (TGA-DSC), X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), energy dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), cyclic voltammetry (CV), galvanostatic charge-discharge (GCD), and electrochemical impedance spectroscopy (EIS). The P-NiCo₂O₄ electrode exhibited a specific capacitance of 1,129 Fg^-1 at a current density of 1 Ag^-1, while the P-NiCo-LDH electrode displayed a specific capacitance of 1,012 Fg^-1 at a current density of 1 Ag-1. When assessing capacity changes for 3,000 cycles, the P-NiCo₂O₄ electrode exhibited a capacity retention rate of 54%, whereas the P-NiCo-LDH electrode showed a capacity retention rate of 57%.

• Journal of the Korean Vacuum Society
• /
• v.19 no.2
• /
• pp.81-90
• /
• 2010

We introduce a novel and versatile approach for preparing self-assembled nanoporous multilayered films with antireflective properties. Protonated polystyrene-block-poly (4-vinylpyrine) (PS-b-P4VP) and anionic polystyrene-block-poly (acrylic acid) (PS-b-PAA) block copolymer micelles (BCM) were used as building blocks for the layer-by-layer assembly of BCM multilayer films. BCM film growth is governed by electrostatic and hydrogen-bonding interactions between the oppositely BCMs. Both film porosity and film thickness are dependent upon the charge density of the micelles, with the porosity of the film controlled by the solution pH and the molecular weight (Mw) of the constituents. PS7K-b-P4VP28K/PS2K-b-PAA8K films prepared at pH 4 (for PS7K-b-P4VP28K) and pH 6 (for PS2K-b-PAA8K) are highly nanoporous and antireflective. In contrast, PS7K-b-P4VP28K/PS2K-b-PAA8K films assembled at pH 4/4 show a relatively dense surface morphology due to the decreased charge density of PS2K-b-PAA8K. Films formed from BCMs with increased PS block and decreased hydrophilic block (P4VP or PAA) size (e.g., PS36K-b-P4VP12K/PS16K-b-PAA4K at pH 4/4) were also nanoporous. Furthermore, we demonstrate that the nanostructured electrochemical sensors based on patterning methods show the electrochemical activities. Anionic poly(styrene sulfonate) (PSS) layers were selectively and uniformly deposited onto the catalase (CAT)-coated surface using the micro-contact printing method. The pH-induced charge reversal of catalase can provide the selective deposition of consecutive PE multilayers onto patterned PSS layers by causing the electrostatic repulsion between next PE layer and catalase. Based on this patterning method, the hybrid patterned multilayers composed of platinum nanoparticles (PtNP) and catalase were prepared and then their electrochemical properties were investigated from sensing $H_2O_2$ and NO gas. This study was based on the papers reported by our group. (J. Am. Chem. Soc. 128, 9935 (2006); Adv. Mater. 19, 4364 (2007); Electro. Mater. Lett. 3, 163 (2007)).

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.28A no.12
• /
• pp.59-64
• /
• 1991

Thin (25-103$\AA$) SiO$_2$ films are grown using the rapid thermal oxidation processing at temperatures of 105$0^{\circ}C$-115$0^{\circ}C$ for 5-30 sec, in order to investigate the characteristics of ultra thin oxide. For measuring the thickness of oxide TEM, ellipsometry, and C-V method which is taken in the condition of small surface band bending are used and compared. When neglecting the small deviation affected by both interface state and moisture charge effect, those three methods described above give similar results. In order to examine the effect of rapid thermal annealing, part of samples are annealed in N$_2$ ambient. MOS capacitors are fabricated and the characteristics of I-V and C-V are measured. Measurements show that the activation energy of initial thickness of oxide grown during the ramp-up time is of 1.125eV and the activation energy of the oxidation rate is of 0.98eV. As oxidation temperature is increased, dielectric breakdown field E$_{BD}$ is decreased due to the increase of fixed charge density N$_f$ However, E$_{BD}$ is shown to be decreased as increasing the thickness of oxide. The increase of N$_f$ in the early stage of thermal annealing results in the decrease of E$_{BD}$.

• Explosives and Blasting
• /
• v.29 no.1
• /
• pp.1-9
• /
• 2011

Air deck charge blasting method which has been generally used in a surface mine and large scale developing site is one of the improved techniques with blasting effectiveness. Many studies and experiments have been tried to investigate the characteristics of pressure distribution in a blasting hole and increase the effectiveness of air deck charge blasting method. In this study, changes of pressure occurred in sections of air deck installed in various ways was computed and also changes of pressure with the location and length of air deck was analyzed, using numerical analysis program. Basically, all the numerical analysis was 2-Dimensional analysis and equation of status of explosives was JWL-EOS. Only to evaluate the variations of pressure in blast hole, it was assumed that rock mass is homogeneous but rock mass has different density and intensity.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.2
• /
• pp.42-52
• /
• 2015

In this study, cellulose nanofibrils (CNF) were modified through carboxymethylation or TEMPO-mediated oxidation and their effects on ionicity and characteristics of sheet, film, and foam were investigated. Carboxymethylation was carried out on pulp fibers as a pre-treatment before preparation of CNF. The gel-like and translucent CNF hydrogel was obtained by grinding of carboxymethylated cellulose fibers. Carboxymethylated CNF film and freeze dried sheet showed higher transparency than that of untreated CNF. The CNF sheet with high strength and the CNF foam without large ice crystals were obtained by using the carboxymethylated CNF. TEMPO-mediated oxidation was carried out as a post-treatment of CNF. The zeta potential and charge demand of TEMPO-oxidized CNF were increased with an increase in oxidation time and addition amount of NaClO. The density of sheet made of TEMPO oxidized CNF was increased with the amount of oxidizing agent. The TEMPO oxidized cellulose nanofiber (TOCN) which was obtained from supernatant after centrifugation could be converted to transparent film.

• Journal of Powder Materials
• /
• v.23 no.4
• /
• pp.317-324
• /
• 2016

Tin is one of the most promising anode materials for next-generation lithium-ion batteries with a high energy density. However, the commercialization of tin-based anodes is still hindered due to the large volume change (over 260%) upon lithiation/delithiation cycling. To solve the problem, many efforts have been focused on enhancing structural stability of tin particles in electrodes. In this work, we synthesize tin nano-powders with an amorphous carbon layer on the surface and surroundings of the powder by electrical wire explosion in alcohol-based liquid media at room temperature. The morphology and microstructures of the powders are characterized by scanning electron microscopy, X-ray diffraction, Raman spectroscopy, and transmission electron microscopy. The electrochemical properties of the powder for use as an anode material for lithium-ion battery are evaluated by cyclic voltammetry and a galvanometric discharge-charge method. It is shown that the carbon-coated tin nano-powders prepared in hexanol media exhibit a high initial charge specific capacity of 902 mAh/g and a high capacity retention of 89% after 50 cycles.

• Journal of Korean Society of Water and Wastewater
• /
• v.12 no.1
• /
• pp.81-87
• /
• 1998

The possibility of collision of two particles slowly settling one after another in water can be described using the collision efficiency factor in differential sedimentation (${\alpha}_{DS}$). ${\alpha}_{DS}$ was found to be a function of several parameters particle size, particle size ratio, Hamaker constant, density of liquid and particle, gravity acceleration. Previous researches were limited to the case when there is no electric repulsion assuming that the suspension is destabilized. In this paper, ${\alpha}_{DS}$ is calculated for the stabilized condition. The relative trajectory of two particles are calculated including hydrodynamics, attraction and repulsion forces. Ionic strength and surface potential significantly affect the collision possibility of two settling particles. Depending on the surface potential and ionic strength, ${\alpha}_{DS}$ value is divided into three regions; stable, unstable and transition zone. ${\alpha}_{DS}$ increases as the ionic strength increases, and as the surface charge decreases. This result can be used to model both destabilized and stabilized suspension incorporating the collision efficiency factors of the other coagulant mechanisms such as fluid shear and Browian motion.