• 대한기계학회논문집A
• /
• 제25권12호
• /
• pp.2100-2108
• /
• 2001

The impinging tones by high-speed plane jets are experimentally investigated to study the edgetone characteristics. Experiment used a slit nozzle and a wedge system to generate edgetones. The jet in the experiment is varied from low to high subsonic speed to obtain the effect of the speed on the frequency characteristics of impinging tones. The experimental data obtained previously fur edgetones and platetones by various nozzles are compared with the present edgetone data. And the condition of tone generation, the frequency ranges, the effective source point and the sound pressure level are compared and discussed. It is found that the jet speed has no diect influence on the impinging tone characteristics. Regardless of the jet speed, the effective source point is about a quarter wavelength downstream from the edge tip. With increase in jet speed, the influence of the nozzle configuration is decreased and the operating frequencies show good coincidences by normalized parameters based on the slit thickness.

• 대한기계학회논문집
• /
• 제8권5호
• /
• pp.442-449
• /
• 1984

본 연구에서는 두 분류가 교우되어 배합이 이루어지는 유동역에서 3차원 방향 에 대하여 평균속도분포, 난류강도분포, 난류전단응력분포, 상관계수의 분포 및 난류 운동에너지와 운동량의 변화 등을 측정 분석하였다.

• 한국분무공학회지
• /
• 제12권2호
• /
• pp.115-122
• /
• 2007

The spray characteristics and drop size measurements have been experimentally studied in liquid jets injected into subsonic crossflow. With water as fuel injection velocity, injection angle and atomize. internal flows were varied to provide of jet operation conditions. The injector internal flow was classified as three modes such as a non-cavitation flow, cavitation, and hydraulic flip flows. Pulsed Shadowgraph Photography measurement was used to determine the spatial distribution of the spray droplet diameter in a subsonic crossflow of air. And this study also obtains the SMD (Sauter Mean Diameters) distribution by using Planar Liquid Laser Induced Fluorescence technique. The objectives of this research are get a droplet distributions and drop size measurements of each condition and compare with the other flow effects. As the result, This research has been showned that droplet size were spatially dependent on air-stream velocity, fuel injection velocity, injection angle effects, and normalized distance from the injector exit length(x/d, y/d). There are also different droplet size characteristics between cavitation, hydraulic flip and the non-cavitation flows.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.486-491
• /
• 2008

The spray characteristics and drop size measurements have been experimentally studied in liquid jets injected into subsonic crossflow. With water as fuel injection velocity, injection angle and atomizer internal flows were varied to provide of jet operation conditions. The injector internal flow was classified as three modes such as a non-cavitation flow, cavitation, and hydraulic flip flows. Pulsed Shadowgraph Photography measurement was used to determine the spatial distribution of the spray droplet diameter in a subsonic crossflow of air. And this study also obtains the SMD(Sauter Mean Diameters) distribution by using PLLIF(Planar Liquid Laser Induced Fluorescence) technique. The objectives of this research are getting a droplet distribution and drop size measurement of each condition and compare with the other flows effect. As the result, This research have been showed the droplet size were spatially dependent on air-stream velocity, fuel injection velocity, injection angle effects and normalized distance from the injector exit length.(x/d, y/d)There are also different droplet size characteristics between cavitation, hydraulic flip and the non-cavitation flows.

• 대한기계학회논문집
• /
• 제5권4호
• /
• pp.257-265
• /
• 1981

A modified subsonic wind tunnel was employed to investigate the turbulent flow of a valve jet. To effectuate this experimental study, an actual valve and valve seat of a diesel engine were equipped at its outlet (ref. Fig. 3) Theoretically, using the equation of motion of Navier-Stokes in the chlindrical coordinates, the turbulent equation of motion for the incompressible fluid was derived with three assumptions; steady flow (.delta./.delta.t=0), axisymmetry and revolutionary homogeneity(.delta./.delta..phi.=0), no ensemble revolution (V.iden.0). Experimentally, mean and fluctuation velocities have been measured in the redial direction. With a assumption of a non-dimensional velocity distribution equation, a sami-emperical similarity profile equation of the jet flow have been derived, whose empirical constants were deterimed graphically with the data obtained.

• 한국군사과학기술학회지
• /
• 제5권1호
• /
• pp.107-115
• /
• 2002

In this paper, spray and combustion characteristics of a liquid-fueled ramjet engine were experimentally investigated. The spray penetrations were measured to clarify the spray characteristics of a liquid jet injected transversely into the subsonic vitiated airstream, which Is maintained a high velocity and temperature. The spray penetrations are increased with decreasing airstream velocity, increasing airstream temperature, and increasing air-fuel momentum ratio. To compensate our results of penetrations, the new experimental equation were modified from Inamura's equation. In the case of insufficient penetration, the combustion phenomenon in ram-combustor were unstable. Therefore, the sufficient penetration must be considered to make a stable flame.

• 한국전산유체공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 2001

Despite the massive effort which has been given to the analysis of the base flows, one commonly occurring case seems to be overlooked. This is for base (rearward facing surface) which is between a subsonic flow and supersonic flow. Potential flows of the air and gas streams are computed for the flow past a separated wake. Then a viscous jet mixing is superimposed on this inviscid solution. Conservation of mass, momentum and energy is achieved by multiple iterations. Despite the iterations, the wake flow field is computed with modest computer requirements.

• EDISON SW 활용 경진대회 논문집
• /
• 제6회(2016년)
• /
• pp.74-77
• /
• 2016

본 연구에서는 Scream Jet Intake에 발생하는 충격파 경계층에서 속도를 Supersonic에서 Subsonic으로 줄였을 때의 상호작용을 EDISON_CFD로 해석하기로 한다. 이상적인 공기 유동에서 충격파 경계층의 각도를 $15^{\circ}{\sim}20^{\circ}$, $25^{\circ}{\sim}30^{\circ}$, $15^{\circ}{\sim}40^{\circ}$, $25^{\circ}{\sim}50^{\circ}$와 같이 두 개($5^{\circ}$, $25^{\circ}$)의 각도 차이를 두어 이중압축램프에서의 유동현상을 EDISON_CFD로 수행하고 분석하였다.

• 한국항공우주학회지
• /
• 제33권9호
• /
• pp.1-8
• /
• 2005

이차원 타원형 날개꼴에서 펄스제트 브로잉에 의한 박리 제어 효과에 대하여 연구하였다. 박리 유동의 능동제어기술 개발을 위하여 압축공기를 사용하는 연속제트/간헐제트 엑츄에이터를 설계제작하여 타원형 날개 풍동 실험 모델에 장착하였다. 아음속 유동에서 날개 주위 유동장의 PIV 측정과 유동의 가시화을 통하여 간헐제트 브로잉의 타원형 날개의 실속제어 효과와 실용성에 대해 실험연구를 수행하였다. PIV 실험 결과 제트 브로잉에 의해 난류 후류 영역과 박리 버블의 크기를 현저하게 감소시킴으로써 박리제어가 가능함을 보였다. 간헐제트는 연속제트보다 박리제어에 보다 효과적이었다. 간헐제트의 주파수를 증가시키면 보다 높은 받음각에 이르기까지 난류 박리 후류를 효과적으로 억제할 수 있었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제24회 춘계학술대회논문집
• /
• pp.155-158
• /
• 2005

The spray characteristics of liquid jet minted in subsonic cross-flow were investigated numerically and experimentally. The behaviors of column, penetration and breakup of plain liquid jet in non-swirling cross-flow of air have been studied. Numerical and physical models are based on a modified KIVAII code. The primary atomization is represented by a wave model based on the KH(Kelvin-Helmholtz) instability that is generated by a high interface relative velocity between the liquid and gas flows. CCD camera has been utilized in oder to capture the spray trajectory. The nozzle diameter was 0.5 mm and its L/D ratios were between 1 and 5. Numerical and experimental results indicate that the breakup point is delayed by increasing gas momentum ratio, the penetration decreases by increasing Weber number and the turbulent or nonturbulent liquid jet is obtained at different L/D ratio.