• Journal of Conservation Science
• /
• v.36 no.2
• /
• pp.82-92
• /
• 2020

Modern artworks are constructed using a variety of materials and techniques. Sculptures, which predominantly consist of metals, usually have different shapes and consist of different material mixtures. The structural and material properties of these sculptures are often controlled by conservation treatment methods. However, the application of existing treatment methods is challenging at times, indicating that more diverse treatment materials and techniques are necessary. Therefore, in this study, a treatment method that employs volatile corrosion inhibitor(VCI) powder, rather than an anti-corrosion solution, for the conservation and management of metal artworks was used. VCI powder and VCI films containing VCI powder were used, and the results obtained confirmed that both of them showed anti-corrosion effect. Only a slight change in the chromaticity of metal samples was observed, and compared to the untreated samples, the application of the VCI powder resulted in a decrease in the rate of corrosion by half. Moreover, VCI film tests revealed that comparing to the untreated or polyethylene film-treated samples, VCI film treatment resulted in a decrease in the occurrence of corrosion compounds. The contact angle, surface energy, and surface electrical resistance were measured, and the evaluation of these surface properties established the anti-corrosion effect of VCI. Additionally, direct application of VCI and VCI films on actual sculptures further confirmed the anti-corrosion effect of VCI.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.4 no.3
• /
• pp.217-226
• /
• 2006

The structural and contamination characteristics of hot cells at KAERI were investigated. The SEM results showed that the size of the hot particulate on the inner surface of the hot cell ranged from 0.2 to $10{\mu}m$. It was found that an inlet flow rate of 15 m/sec was suitable for this developed cyclone with a 49 mm optimum vortex finder length. The results showed that the collection efficiency was about 85% for $3{\mu}m$ particles. The collection efficiency didn't show a sharp increase when the inlet flow rate was faster than 15m/sec. When the temperature of the inlet flow gas was increased, the collection efficiency of the cyclone was slightly decreased. The larger the vortex finder length was, the higher the pressure drop in the cyclone was. The cut size diameter decreased with an increment of the Reynolds number. It was established that the flow in the cyclone was a turbulent flow on the basis of the Reynolds number and this turbulent flow caused a pressure drop in the cyclone. $Stk^{1/2}_{50}$ decreased with increasing values of the Reynolds number and it gradually approached a constant value at a higher value of the Reynolds number Namely, $Stk^{1/2}_{50}$ approached approximately 0.045 between 6000 and 8000 of the Reynolds number.

• The Journal of Industrial Distribution & Business
• /
• v.9 no.2
• /
• pp.57-63
• /
• 2018

Purpose - This research examined the effect of hedonic and utilitarian eating-out motivations on the evaluation of restaurant selection attributes in a fashion premium outlet. Additionally, the influence of experimental and functional attributes on customers' preference for hedonic eating-out motives and utilitarian eating-out motives, and variation of moderating effects through the gender was examined. Research design, data, and methodology - A survey was conducted to verify the established research hypothesis. The questionnaire items for the research were modified to fit the situation of the present study. In order to elaborate the questionnaire, the literature of the previous researchers was reviewed and supplemented. The survey conducted 207 online questionnaires for consumers who have visited domestic fashion premium outlets from July 4, 2017 to July 27, 2017. A total of 207 questionnaires were collected, and a total of 206 questionnaires were used for the empirical analysis after excluding one inappropriate response. In order to verify the reliability and validity of the measured variables, exploratory factor analysis and reliability analysis were performed using SPSS 20.0. Next, the structural equation model (SEM) statistical method was used to test the hypotheses of the study. Results - Hedonic motivation had more influence on experimental attribute importance than the functional attribute importance of the restaurant. However, this result was different depending on the gender. The effects of hedonic motives on empirical attributes were more influenced by female groups, and when influencing functional attributes, male groups were more influenced. However, it was statistically significant (p <0.05) in the female group only when the hedonic eating out motives influenced empirical attributes. Conclusions - This study analyzed the effect of eating-out motivation on the restaurant preference attributes and suggested practical implications. First, customers with hedonic eating-out motivations were evaluating experiential attributes to be more important than functional attributes. Second, for customers who are motivated to use practical eating-out habits, companies should provide services that meet practical and economic needs. In particular, female customers visiting restaurants need differentiated marketing strategies that make them feel new experiences rather than practical ones. In addition, it is necessary to study more complex and integrated studies which will influence restaurant selection attributes of premium outlets customers by adding various eating out motives and selection attributes.

• Journal of Biomedical Engineering Research
• /
• v.30 no.2
• /
• pp.135-141
• /
• 2009

Purpose: The aim of present study is to evaluate a possibility of clinical application for the effect of low intensity ultrasound stimulation (LIUS) in mechanical characteristics of bone on osteoporotic fractures prevention. Materials and Methods: Eight virgin ICR mice (14 weeks old, approximate weight 25g) were ovariectomized (OVX) to induce osteoporosis. The right hind limbs were then stimulated with LIDS (US Group), whereas left hind limbs were not stimulated (CON Group). Both hind limbs of all mice were scanned by in-vivo micro-CT to acquire two-dimensional (2D) images at 0 week before stimulation and 3 weeks and 6 weeks after stimulation. Three-dimensional (3D) finite element (FE) models generated by scanned 2D images were used to determine quantitatively the effect of LIUS on strength related to bone structure. Additionally, distributions of Hounsfield units and elastic moduli, which are related to the bone quality, for the bones in the US and CON groups were determined to analyze quantitatively a degree of improvement of bone qualities achieved by LIUS. Results: The result of FE analysis showed that the structural strength in US Group was significantly increased over time (p<0.05), while that in CON Group was statistically constant over time (p>0.05). High values of Hounsfield units obtained from voxels on micro-CT images and high values of elastic moduli converted from the Hounsfield units were dominantly appeared in US Group compared with those in CON Group. Conclusion: These finding indicated that LIUS would improve the mechanical characteristics of osteoporotic bone via the effects of bone structure (bone strength) and quality (Hounsfield unit and elastic modulus). Therefore, the LIUS may decrease effectively the risk of osteoporotic fracture in clinics.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.2
• /
• pp.50-55
• /
• 2018

Earthquakes are almost impossible to predict and take place in a short time. In addition, there is little time to take aggressive action when an earthquake occurs. Therefore, there are more casualties and property damage than with other natural disasters. Recently, earthquakes have been occurring all over the world. As the number of earthquakes increase, studies on the safety of structures are being carried out. On the other hand, there are few studies on the electric facilities, which are relatively non - structural factors. Currently, electrical equipment in Korea is often not designed for earthquake safety and is quite vulnerable to damage when an earthquake occurs. Therefore, in this study, modeling was conducted through ABAQUS similar to an actual cabinet panel and 3D dynamic nonlinear analysis was performed using a natural seismic. According to seismic zone I and normal ground rock conditions of the power transmission and transmission facility seismic design practical guide, the maximum response acceleration of the performance level was 0.157g. In this study, however, it was not safe to reach the limit state of 30% of the analytical result at 0.1g for the general cabinet panel. From the results, the seismic fragility curve was derived and analyzed. The derived seismic fragility curve is presented as a quantitative basis for determining the limit state of the cabinet panel and can be utilized as basic data in related research.

• The Korean Journal of Pesticide Science
• /
• v.2 no.2
• /
• pp.53-58
• /
• 1998

For evaluating the mutagenic potential of 2-carbomethoxy-4-chlorodiethyl phosphate, three different short-term mutagenicity tests were used; Salmonella typhimurium preincubation assay with and without rat liver microsomal activation, chromosome aberration test in cultured chinese hamster lung fibroblast cell and in vivo micronucleus test in male mice bone marrow. In Salmonella typhimurium reverse mutation assay using TA98, TA100, TAl535 and TAl537, 2-carbomethoxy-4-chlorodiethyl phosphate did not show any mutagenic response in the presence and absence of S9 mix. It did not induce any significant structural chromosome aberrations in the absence of metabolic activation. In micronucleus test using ICR mice, the frequency of micronucleated polychromatic erythrocytes (MNPCE) increased in bone marrow cells treated with positive control, mitomycin-C, but 2-carbomethoxy-4-chlorodiethyl phosphate did not increase micronucleated polychromatic erythrocytes. These results indicate that 2-carbomethoxy-4-chlorodiethyl phosphate does not show any positive responses in short-term genotoxicity assays.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.1
• /
• pp.395-405
• /
• 2017

In this research, we analyzed the structural (influence) of citizens' political awareness and political participation on the settlement of political culture. The results are as follows. Firstly, the analysis of the relationship between the citizens' political awareness and political reliability in Hypothesis 1 showed that the higher their election sense and self-efficacy, the higher their satisfaction with and evaluation of politics. Secondly, the analysis of the relationship between the citizens' political awareness and social sense of belonging in Hypothesis 2 showed that the higher the election sense and recognition in society, the higher the social sense of belonging. Thirdly, the analysis of the influence of political reliability on political participation in Hypothesis (3) showed that the higher the political satisfaction and political assessment, the higher the positive participation in politics and negative participation in politics. Fourth, in the analysis of the influence of social sense of belonging on political participation in Hypothesis 4, it was found that the higher the citizens' social belonging awareness, the higher the positive political participation and negative political participation. Therefore, it was found that the higher the political awareness of the citizens, such as their election sense and knowledge about their politicians, the more positive were their political reliability and political participation.

• International Journal of Contents
• /
• v.11 no.1
• /
• pp.41-51
• /
• 2015

Management systems for electronic library have been developed on the basis of Client/Server or ASP framework in domestic market for a long time. Therefore, both service provider and user suffer from their high cost and effort in management, maintenance, and repairing of software as well as hardware. Recently in addition, mobile devices like smartphone and tablet PC are frequently used as terminal devices to access computers through the Internet or other networks, sophisticatedly customized or personalized interface for n-screen service became more important issue these days. In this paper, we propose a new scheme of integrated management system for electronic library based on SaaS and Web Standard. We design and implement the proposed scheme applying Electronic Cabinet Guidelines for Web Standard and Universal Code System. Hosted application management style and software on demand style service models based on SaaS are basically applied to develop the management system. Moreover, a newly improved concept of duplication check algorithm in a hierarchical evaluation process is presented and a personalized interface based on web standard is applied to implement the system. Algorithms of duplication check for journal, volume/number, and paper are hierarchically presented with their logic flows. Total framework of our development obeys the standard feature of Electronic Cabinet Guidelines offered by Korea government so that we can accomplish standard of application software, quality improvement of total software, and reusability extension. Scope of our development includes core services of library automation system such as acquisition, list-up, loan-and-return, and their related services. We focus on interoperation compatibility between elementary sub-systems throughout complex network and structural features. Reanalyzing and standardizing each part of the system under the concept on the cloud of service, we construct an integrated development environment for generating, test, operation, and maintenance. Finally, performance analyses are performed about resource usability of server, memory amount used, and response time of server etc. As a result of measurements fulfilled over 5 times at different test points and using different data, the average response time is about 62.9 seconds for 100 clients, which takes about 0.629 seconds per client on the average. We can expect this result makes it possible to operate the system in real-time level proof. Resource usability and memory occupation are also good and moderate comparing to the conventional systems. As total verification tests, we present a simple proof to obey Electronic Cabinet Guidelines and a record of TTA authentication test for topics about SaaS maturity, performance, and application program features.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.3
• /
• pp.1645-1651
• /
• 2015

This paper describes the changes of shape accuracy in workpiece materials depending on the turning clearance angle. The experiments started from choosing three workpiece materials, SM45C(machine structural carbon steel), STS303(stainless steel) and SCM415 (chrome-molybdenum steel). The experiments showed specifically how features of selected materials changed when they were processed with diverse machining depths, 0.1 mm, 0.2 mm and 0.3 mm, with various negative angles, $0.0^{\circ}(-6.0^{\circ})$, $0.3^{\circ}(-6.3^{\circ})$ and $0.9^{\circ}(-6.9^{\circ})$, and called cutting edge inclination starting from a fixed rotational speed, 2,500 rpm, focusing on the feed rate, 0.07 mm/rev and 0.10 mm/rev. The results of the accuracy of processing, cylindricity, deviation from coaxiality, etc. were compared using the graph and table. The accuracy of cylindricity in the order of degree $0.0^{\circ}{\rightarrow}0.3^{\circ}{\rightarrow}0.9^{\circ}$ depending on the workpiece materials showed the best cylindricity when it was $0.9^{\circ}$. In conclusion, the accuracy improved in specific degrees irrespective of the quality of the materials when the bite negative angles increased. This means that workability improved in these experiments. In addition, the processing shape changed depending on depth of the cut and feed rate.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.3
• /
• pp.452-459
• /
• 2017

In recent years, to reduce self-weight of structural elements, the use of SCP (Steel Concrete Plate) instead of prestressed concrete is increasing. Because SCP has a complicated sectional shape and includes a large number of studs, the use of high-fluidity concrete is required. Therefore, in this study, to prevent the restrained shrinkage behavior by the stud, the effects of using an expansive agent (EA) and shrinkage reducing agent (SRA) were investigated, and the optimal mixture proportions to maximize the filling capacity were determined based on the fine aggregate ratio. The test results indicated that the combined use of EA and SRA exhibited the smallest shrinkage. The ratio of the crushed sand and washed sea sand was determined to be 5:5, and the proper fine aggregate ratio was found to be 55.6%, because when the ratio was too high, a decrease in strength and an increase in shrinkage strain were expected. The high-fluidity concrete effectively filled the large-sized SCP module.