• Journal of the Korea Institute of Military Science and Technology
• /
• v.9 no.1 s.24
• /
• pp.144-151
• /
• 2006

A rectangular loop antenna for S-band radar is proposed. The proposed loop antenna is the modified type of folded monopole antenna. The feeding line is coplanar stripline with $180^{\circ}$ phase difference for operating in odd mode. The proposed antenna showed return loss of -15.57dB at the center frequency and bandwidth of about 790MHz (> 25%) under the condition of VSWR < 2. The gains of single, 1x2, and 1x4 array loop antennas are 4.3, 7.0, and 10.2dBi, respectively.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.4C no.6
• /
• pp.300-305
• /
• 2004

In this paper, new design equations based on the pole-zero analysis for multi-layered interdigital stripline linear group delay bandpass filter with tap input ports are presented. As a design example, a four-pole group delay filter with center frequency of 2.14GHz, bandwidth of 160MHz, and group delay variation of $\pm$0.1nS for LTCC technology or multilayered PCB technology is designed. In the design process, it is not necessary to simulate the entire structure, as the simulation of half structures is sufficient. Good results can be attained after the optimizing process was performed three times using the proposed equations and a commercial EM simulator.

• Progress in Superconductivity
• /
• v.4 no.1
• /
• pp.64-67
• /
• 2002

The attenuation of millimeter waves (70-100 ㎓) propagating along Josephson Junction stripline had been measured by pattern recognition near gap voltage and proximity current bump. Test series arrays of 2000, 3000, and 4000 Josephson junctions with the area of $12\mu\textrm{m}$$\times$ $38\mu\textrm{m}$ had two sub-arrays with 50 Junctions at both ends. The arrays were fabricated with and without applying a plasma nitridation process to Nb ground plane. The effects of a nitridationprocess measured by the pattern recognition near gap voltage and proximity current bump were about 1.3-1.7 ㏈ and 1.6-1.8 ㏈, respectively. This means that the last sub-arrays with a nitridation process receive 26-34% more power than those without a nitridation process.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.180-180
• /
• 2012

A microplasma system source based on microwave parallel stripline resonator (MPSR) was developed for the generation of microplasmas in a wide range of pressure from some torr to 760 torr. This source was operated at its resonance frequency that much depends upon not only its discharge gap size but also operated pressure. This paper applied a simple circuit model to analyze the effects of discharge gap size and pressure to resonance frequency and impedance of MPSR in the cases with and without plasma exist inside the discharge gap. In the process of calculating, the conformal mapping method was used to estimate the capacitance of the MPSR. The calculating results by using circuit model agree well with the simulation results that using commercial CST microwave studio software.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.2
• /
• pp.170-175
• /
• 2002

The cut-off frequencies of higher order modes in a symmetrical stripline are calculated using the variational finite element method combined with the conformal mapping. The conformal mapping is used to Improve the modeling of the infinite transverse extents of a stripline. And then the finite element method is employed to solve the variational equation in the transformed finite region. Comparisons with numerical results found in the literature validate the presented method.

• Journal of electromagnetic engineering and science
• /
• v.11 no.3
• /
• pp.227-233
• /
• 2011

This paper describes the development of a broadband quasi-Yagi antenna using a folded dipole driver. The antenna is designed on a low-permittivity substrate to reduce the surface wave effect, and hence the gain can be enhanced easily by adding directors. The folded dipole driver is connected to a 50-${\Omega}$ microstripline via a simple broadband microstrip-to-coplanar stripline transition with a quarter radial stub. The key motivation for the use of a folded dipole is to increase the input impedance at the driver, allowing a smaller mismatch loss between the antenna driver and the coplanar stripline feed. The proposed antenna has a measured bandwidth of 4.67~6.26 GHz for the -10 dB reflection coefficient, and a flat gain of 4.86~5.15 dB within the bandwidth.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.8
• /
• pp.740-743
• /
• 2003

A multi-layer ceramic (MLC) chip type band-pass filter (BPF) is presented. The MLC chip BPF has the benefits of low cost and small size. The BPF consists of coulped stripline resonators and coupling capacitors. The BPF is designed to have an attenuation pole at below the passband for a receiver band of IMT-2000 handset. The computer-aided design technology is applied for analysis of the BPF frequency characteristics. The passband and attenuation pole depend on the coupling between resonators and coupling capacitance. The frequency characterics of the passband and attenuation pole are analyzed with the variation of the coupling between resonators and coupling capacitance. An equivanlent circuit and structure of MLC chip BPF are proposed. The frequency characteristics of the BPF is well acceptable for IMT-2000 application.

• Proceedings of the IEEK Conference
• /
• 2007.07a
• /
• pp.187-188
• /
• 2007

A stripline fed slot antenna for UWB communication is designed by using Ensemble simulator. The antenna has a broadband characteristics which causes a fork-like tuning stub. The ground of this antenna has two conductor lines for WLAN band(5GHz band) rejection.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.265-268
• /
• 2003

In RF application of resonator, cylinerical and transmission line(TRL) type are used generally, especially in ceramic modules the latter is used widely, TRL type resonators are used in VCO and RF filters etc.. TRL type resonators are divided stripline and microstripline and their characteristics depend on that of conductor and dielectric materials. In this study, the effect of material properties on the stripline resonator is measured and analyzed. Besides, the optimum design rule of resonator is presented.

• Journal of IKEEE
• /
• v.12 no.3
• /
• pp.144-150
• /
• 2008

This paper describes the design of a coplanar-stripline(CPS) antenna without via hole in microstrip patch type for 910MHz RFID tags using the HFSS simulator. In order to obtain the simplified fabrication design of the antenna, we have used only an impedance matching network to match the impedance of a RFID-tag chip to that of the antenna, not using bandpass filter(BPF). In advance of the optimized antenna design, we have obtained and shown a good agreement compared with the published antenna for 5.8GHz in order to verify the simulation parameters in the HFSS. Based on the verified simulation parameters in the HFSS, we have designed and optimized the 910MHz-CPS-type microstrip patch antenna. The designed simulation results of the antenna show that the proposed antenna is very proper for RFID tags with the 910MHz center frequency without via hole in the microstrip patch antenna.