• Smart Structures and Systems
• /
• 제30권1호
• /
• pp.63-74
• /
• 2022

The deformation coordination between a rock/soil mass and an optical sensing cable is an important issue for accurate deformation monitoring. A stress-controlled triaxial apparatus was retrofitted by introducing an optical fiber into the soil specimen. High spatial resolution optical frequency domain reflectometry (OFDR) was used for monitoring the strain distribution along the axial direction of the specimen. The results were compared with those measured by a displacement meter. The strain measured by the optical sensing cable has a good linear relationship with the strain calculated by the displacement meter for different confining pressures, which indicates that distributed optical fiber sensing technology is feasible for soil deformation monitoring. The performance of deformation coordination between the sensing cable and the soil during unloading is higher than that during loading based on the strain transfer coefficients. Three hypothetical strain distributions of the triaxial specimen are proposed, based on which theoretical models of the strain transfer coefficients are established. It appears that the parabolic distribution of specimen strain should be more reasonable by comparison. Nevertheless, the strain transfer coefficients obtained by the theoretical models are higher than the measured coefficients. On this basis, a strain transfer model considering slippage at the interface of the sensing cable and the soil is discussed.

• Smart Structures and Systems
• /
• 제18권6호
• /
• pp.1203-1215
• /
• 2016

When strain sensing cables are under long-term stress and cyclic loading, creep may occur in the jacket material and each layer of the cable structure may slide relative to other layers, causing fatigue in the cables. This study proposes a device for testing the fatigue characteristics of three types of cables operating under different conditions to establish a decay model for observing the patterns of strain decay. The fatigue characteristics of cables encased in polyurethane (PU), GFRP-reinforced, and wire rope-reinforced jackets were compared. The findings are outlined as follows. The cable strain decayed exponentially, and the decay process involved quick decay, slow decay, and stabilization stages. Moreover, the strain decay increased with the initial strain and tensile frequency. The shorter the unstrained period was, the more similar the initial strain levels of the strain decay curves were to the stabilized strain levels of the first cyclic elongation. As the unstrained period increased, the initial strain levels of the strain decay curves approached those of the first cyclic elongation. The tested sensing cables differed in the amount and rate of strain decay. The wire rope-reinforced cable exhibited the smallest amount and rate of decay, whereas the GFRP-reinforced cable demonstrated the largest.

• The Korean Journal of Ceramics
• /
• 제5권2호
• /
• pp.165-170
• /
• 1999

The strain sensing properties of th system xNiO-(1-x) CaO with various compositions (x=0.001-0.05) are evaluated and the origin of the phenomena is guessed. We have found out that the high temperature electrical conductivity of the xNiO-(1-x)CaO increases by applying the compressive stress at $1000^{\circ}C$. When the applied load is removed, the electrical conductivity rapidly decreases and returns to the original value, but a small hysteresis of the stress-conductivity curve is observed. After the loading test, the lattice parameter of the specimen is found lengthened. The correlation between the lengthening of the lattice parameter and the increases in the electrical conductivity by loading is discussed. The amount of the "expanded type" Ni(II)O6 clusters in the xNiO-(1-x)CaO grains is supposed to be increased by the applied stress, which would be the origin of the strain dependent electric conduction in the xNiO-(1-x)CaO system.aO system.

• 한국지반공학회논문집
• /
• 제40권2호
• /
• pp.115-123
• /
• 2024

응력은 비가시 물리량이므로, 지반 내부에서 이를 측정하기 위해서는 토압계가 필요하다. 기존의 스트레인 게이지 기반 토압계는 큰 강성을 가지며, 이는 지반 내부 응력을 교란시켜 토압 측정의 정확성에 영향을 준다. 박막형 압전센서는 얇고 유연하므로, 이를 활용할 경우 지반 내부 응력의 교란을 최소화하여 지중응력을 측정할 수 있다. 본 연구에서는 박막형 압전 센서를 활용하여 지반 내부의 응력을 측정하기 위한 시스템을 구축하였다. 박막형 압전 센서를 교정하기 위한 챔버를 제작하여 사질토 지반 내부에 매설된 박막형 압전 센서의 측정 변동성과 센서의 감지 영역에 부착된 퍽으로 인한 측정 토압의 재현성 향상을 반복실험을 통해 확인하였다.

• Structural Monitoring and Maintenance
• /
• 제9권3호
• /
• pp.259-270
• /
• 2022

This study explores the use of the recently developed "strain-sensing smart skin" (S⁴) method for noncontact strain measurements on cement-based samples. S⁴ sensors are single-wall carbon nanotubes dilutely embedded in thin polymer films. Strains transmitted to the nanotubes cause systematic shifts in their near-infrared fluorescence spectra, which are analyzed to deduce local strain values. It is found that with cement-based materials, this method is hampered by spectral interference from structured near-infrared cement luminescence. However, application of an opaque blocking layer between the specimen surface and the nanotube sensing film enables interference-free strain measurements. Tests were performed on cement, mortar, and concrete specimens with such modified S⁴ coatings. When specimens were subjected to uniaxial compressive stress, the spectral peak separations varied linearly and predictably with induced strain. These results demonstrate that S⁴ is a promising emerging technology for measuring strains down to ca. 30 𝜇𝜀 in concrete structures.

• Smart Structures and Systems
• /
• 제21권1호
• /
• pp.27-35
• /
• 2018

In the water-filling and preloading test, the sensing cables were installed on the surface of steel spiral case and in the surrounding concrete to monitor the strain distribution of several cross-sections by using Brillouin Optical Time Domain Analysis (BOTDA), a kind of distributed optical fiber sensing (DOFS) technology. The average hoop strain of the spiral case was about $330{\mu}{\varepsilon}$ and $590{\mu}{\varepsilon}$ when the water-filling pressure in the spiral case was 2.6 MPa and 4.1 MPa. The difference between the measured and the calculated strain was only about $50{\mu}{\varepsilon}$. It was the first time that the stress adjustment of the spiral case was monitored by the sensing cable when the pressure was increased to 1 MPa and the residual strain of $20{\mu}{\varepsilon}$ was obtained after preloading. Meanwhile, the shrinkage of $70{\sim}100{\mu}{\varepsilon}$ of the surrounding concrete was effectively monitored during the depressurization. It is estimated that the width of the gap between the steel spiral case and the surrounding concrete was 0.51 ~ 0.75 mm. BOTDA based distributed optical fiber sensing technology can obtain continuous strain of the structure and it is more reliable than traditional point sensor. The strain distribution obtained by BOTDA provides strong support for the design and optimization of the spiral case structure.

• 대한기계학회논문집B
• /
• 제33권10호
• /
• pp.773-777
• /
• 2009

In this study, the strain sensing characteristics of single-wall carbon nanotubes(SWCNTs) networks were investigated to develop a film sensor for strain sensing. The SWCNTs film are formed on flexible substrates of poly(ethylene terephthalate) (PET) using spray process. In this manner we could control the transparency and obtain excellent uniformity of the networked SWCNT film. The carbon nanotube film is isotropic due to randomly oriented bundles of SWCNTs. Using experimental results it is shown that there is a nearly linear change in resistance across the film when it is subjected to tensile stress. The results presented in this study indicate the potential of such films for high sensitive transparent strain sensors on macro scale.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.212-215
• /
• 2002

Interfacial evaluation and damage sensing of the carbon fiber/epoxy-amine terminated (AT)-polyetherimide (PEI) composites were performed using micromechanical test and electrical resistance measurement. As AT-PEI content increased, the fracture toughness of epoxy-AT-PEI matrix increased, and thus their interfacial shear strength (IFSS) was improved due to the improved toughness. After curing process, the changes in electrical resistance (ΔR) with increasing AT-PEI contents increased gradually because of the changes in thermal expansion coefficient (TEC) and thermal shrinkage of matrix. Matrix fracture toughness was correlated to the IFSS, residual stress and electrical resistance. The results obtained from the electrical resistance measurement during curing process, reversible stress/strain, and durability test were consistent with modified matrix toughness properties.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.698-703
• /
• 2001

This paper is concerned with the nonlinear hyperelastic problem fur the incompressible characteristics of the rubber. Tension sensor is a strain gage type load cell element for a fence intrusion detection system and consists of the sensing part and the rubber housing. The analysis includes an elastic analysis and a hyperelastic analysis of a tension sensor for the deformed shape and variation of the maximum strain on the sensing part with respect to the vertical load. Numerical results show that the hyperelastic model is stiffer and less deformed than the elastic model. Comparing with the experimental test data, we know the hyperelastic model is the better approximation than the elastic model.

• 한국방재학회 논문집
• /
• 제6권3호
• /
• pp.9-16
• /
• 2006

기존 대부분의 구조물 건전도 모니터링 시스템에서는 제한적인 위치와 범위에서의 변형률 계측이 가능한 국부 변형률 센서를 이용하여 구조물 또는 구조 부재의 부재력을 계측하고 이에 기반하여 구조 안전성을 평가하고 있다. 그러나 실 구조물의 부재력 계측을 통한 안전성 평가는 하중의 크기 및 분포에 대한 불확실성 등의 다양한 이유로 부재 내 최대응력 작용점을 정확하게 파악하기 어렵다. 이러한 경우 구조물의 사이즈에 비하여 센서의 길이가 미소한 국부 변형률 센서를 이용한 안전성 평가의 적절성은 센서의 위치 및 개수에 좌우되는 한계를 가지게 된다. 이러한 한계를 극복하기 위하여 센서의 수를 증가시키면 처리해야하는 데이터의 양과 비용이 증가하게 되므로 현실적인 적용성에 문제점을 가지게 된다. 그러므로 본 연구에서는 이러한 한계와 문제점을 극복할 수 있는 대안으로 장대광변형센서에 의한 평균변형률을 이용한 보-기둥의 부재력 계측 기법을 제시하였다.