• Structural Engineering and Mechanics
• /
• v.32 no.2
• /
• pp.269-282
• /
• 2009

Responding to the threat of terrorist attacks around the world, numerous studies have been conducted to search for new methods of vulnerability assessment and protective technologies for critical infrastructure under extreme bomb blasts or high velocity impacts. In this paper, a two-dimensional behavioral rate dependent lattice model (RDLM) capable of analyzing reinforced concrete members subjected to blast and impact loading is presented. The model inherently takes into account several major influencing factors: the progressive cracking of concrete in tension, the inelastic response in compression, the yielding of reinforcing steel, and strain rate sensitivity of both concrete and steel. A computer code using the explicit algorithm was developed based on the proposed lattice model. The explicit code along with the proposed numerical model was validated using experimental test results from the Woomera blast trial.

• Transactions of Materials Processing
• /
• v.31 no.4
• /
• pp.200-206
• /
• 2022

The finite element analysis is one of the representative methods for predicting the materials behavior for experiments that are difficult to perform empirically. Constitutive equations are essential for reducing computation time and sharing data because they enable finite element analysis simulations through simple formulae. However, it is difficult to derive accurate flow curves for all materials as most constitutive equations are not formulated based on their physical meaning. Also, even if the constitutive equation is a good representation of the flow curve to the experimental results, some fundamental issues remain unresolved, such as the effect of mesh size on the calculation results. In this study, a new constitutive equation was proposed to predict various materials by modifying the combined Swift-Voce model, and the calculation results with various mesh sizes were compared to better simulate the experimental results.

• Korean Journal of Materials Research
• /
• v.28 no.12
• /
• pp.738-747
• /
• 2018

For the aerospace structural application of high-strength 2xxx series aluminum alloys, stress corrosion cracking(SCC) behavior in aggressive environments needs to be well understood. In this study, the SCC sensitivities of 2024-T62, 2124-T851 and 2050-T84 alloys in a 3.5 % NaCl solution are measured using a constant load testing method without polarization and a slow strain rate test(SSRT) method at a strain rate of 10-6 /sec under a cathodic applied potential. When the specimens are exposed to a 3.5 % NaCl solution under a constant load for 10 days, the decrease in tensile ductility is negligible for 2124-T851 and 2050-T84 specimens, proving that T8 heat treatment is beneficial in improving the SCC resistance of 2xxx series aluminum alloys. The specimens are also susceptible to SCC in a hydrogen-generating environment at a slow strain rate of $10^{-6}/sec$ in a 3.5 % NaCl solution under a cathodic applied potential. Regardless of the test method, low impurity 2124-T851 and high Cu/Mg ratio 2050-T84 alloys are found to have relatively lower SCC sensitivity than 2024-T62. The SCC behavior of 2xxx series aluminum alloys in the 3.5 % NaCl solution is discussed based on fractographic and micrographic observations.

• Computers and Concrete
• /
• v.19 no.1
• /
• pp.33-39
• /
• 2017

In this study, two types of aggregate were used for making self-compacting concrete. Standard cubic specimens were exposed to different temperatures. Seventy-two standard cylindrical specimens ($150{\times}300mm$) and Seventy-two cubic specimens (150 mm) were tested. Compressive strengths of the manufactured specimens at $23^{\circ}C$ were about 33 MPa to 40 MPa. The variable parameters among the self-compacting concrete specimens were of sand stone type. The specimens were exposed to 23, 100, 200, 400, 600, and $800^{\circ}C$ and their mechanical specifications were controlled. The heated specimens were subjected to the unconfined compression test with a quasi-static loading rate. The corresponding stress-strain curves and modulus of elasticity were compared. The results showed that, at higher temperatures, Scoria aggregate showed less sensitivity than ordinary aggregate. The concrete made with Scoria aggregate exhibited less strain. The heated self-compacting concrete had similar slopes before and after the peak. In fact, increasing heat produced gradual symmetrical stress-strain diagram span.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.49 no.4
• /
• pp.198-207
• /
• 2023

Objectives: This study investigated causative strains and their antibiotic sensitivity in patients who were hospitalized for maxillofacial odontogenic infections at a tertiary center in South Korea over the past 10 years with the aim of providing guidelines for the selection of appropriate empirical antibiotics. Materials and Methods: Patients with head and neck fascial space abscesses due to odontogenic infections who underwent incision and drainage surgery with pus culture tests between 2013 and 2022 at the Department of Oral and Maxillofacial Surgery, Dankook University Hospital were included. The bacterial isolates and antibiotic sensitivity of each strain were analyzed for 2013-2022, 2013-2017, and 2018-2022. The affected fascial spaces were classified into primary, secondary, and deep neck spaces. Results: In the 192 patients included in this study, 302 strains were detected. Viridans streptococcus had the highest frequency (51.7%), followed by Prevotella spp. (16.9%), Staphylococcus spp. (5.6%), and Klebsiella pneumoniae (4.6%). The identification rate of viridans streptococcus significantly increased from 41.8% in 2013-2017 to 60.9% in 2018-2022. Viridans streptococcus showed an antibiotic sensitivity of 80.5% to ampicillin; the sensitivity to penicillin antibiotics decreased over the study period. Antibiotic susceptibility was approximately 94% for third-generation cephalosporins. K. pneumoniae, which was identified at a high percentage in patients with deep neck space infection, showed increasing antibiotic resistance to most antibiotics over the study period. Conclusion: Viridans streptococcus was identified in head and neck fascial space abscesses with the highest frequency. Empirical antibiotics should be effective against this strain; penicillin antibiotics are considered inappropriate. For effective treatment of deep neck space abscesses, bacterial culture and antibiotic sensitivity tests performed as soon as possible are essential.

• Journal of Ocean Engineering and Technology
• /
• v.10 no.1
• /
• pp.53-64
• /
• 1996

In this paper, rotating bending fatigue tests have been carried out to investigate the growth behabiors of surface fatigue crack initiated from a small artificial surface defect, that might exist in real structures, on 2024-T3 and 6:4 brass. The test results are analysed in the viewpoints of both strength of materials and fracture mechanics, it can be concluded as follows. The effect of a small artificial surface defect upon the fatigue strength is very large. The sensitivity of 2024-T3 on the defect is higher than that of 6:4 brass. The growth behavior of the surface fatigue crack of 2024-T3 is different from that of 6:4 brass. The growth rate of the surface fatigue crack of 2024-T3 is considerably rapid in the early stage of the fatigue life and apt to decrease in the later stage. It was impossible to establish a unifying approach in the analysis of crack growth begabior of 2024-T3 and 6:4 brass using the maximum stress intensity factor because of their dependence on stress level. But if the elastic strain and cyclic total strain intensity factor range were applied to obtain the growth rate of surface fatigue cracks of the materials, the data were found to be nearly coincided.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.20 no.1
• /
• pp.66-74
• /
• 2024

This study investigates the effects of temperatures and strain rates on the strength and ductility of Gr.91 (ASME Grade 91) steel which is widely being used as a heat-resistant material in Generation IV nuclear and super critical thermal power plants. The tensile behavior of modified 9Cr-1Mo (Gr.91) steel was studied for the three strain rates of 6.67×10^-5/s, 6.67×10^-4/s and 6.67×10-3/s over the temperature range from room temperature (RT) to 650℃. Experimental results showed that at specific combinations of temperatures (300~400℃) and strain rates, serrations appeared in the stress-strain curves. Concurrently, abnormal behaviors such as a plateau in yield strength and tensile strength, a minimum in ductility and negative strain rate sensitivity were observed. These phenomena were analyzed as significant characteristics of dynamic strain aging (DSA). Since this abnormal behavior in Gr.91 steel affects the material strength, it is judged that a correlation analysis between DSA and material strength should be crucial in the design and integrity evaluation of Gr. 91 steel pressure vessel and piping subjected to high-temperature loading.

• Analytical Science and Technology
• /
• v.9 no.2
• /
• pp.179-191
• /
• 1996

In order to understand the high temperature deformation behavior of superalloy 718, a rotating grade 718 alloy has been compression tested to about 0.7 upset ratio at $927{\sim}1066^{\circ}C$ temperature range and $5{\times}10^{-4}{\sim}5{\times}10^0sec^{-1}$ strain rate. The maximum flow stress was increased with increasing strain rate, and similar behavior was observed with decreasing temperature. At low temperature and high strain rates other than $5{\times}10^{-1}sec^{-1}$, strain softening was occurred mainly by dynamic recovery and deformation twinning processes, while at high temperature and low strain rates strain softening was offseted by dynamic recrystallization. At $5{\times}10^{-1}sec^{-1}$, strain hardening was occurred due to work hardening of the dynamic recrystallized grains. Strain rate sensitivity, m, was varied with strain rates. In the case of lower strain rate tests, m was measured as 0.3 and it was observed that the deformation was mainly controlled by dynamic recrystallization. At higher strain rate, m was lowered to 0.1 and the deformation was controlled by the dynamic recovery and the deformation twinning processes.

• Korean Journal of Materials Research
• /
• v.28 no.8
• /
• pp.435-439
• /
• 2018

MA Al alloys are examined to determine the effects of alloying of Mg and Cu and rolling on tensile deformation behavior at 748 K over a wide strain rate range($10^{-4}-10^3/s$). A powder metallurgy aluminum alloy produced from mechanically alloyed pure Al powder exhibits only a small elongation-to-failure(${\varepsilon}_f$ < ~50%) in high temperature(748 K) tensile deformation at high strain rates(${\acute{\varepsilon}}=1-10^2/s$). ${\varepsilon}_f$ in MA Al-0.5~4.0Mg alloys increases slightly with Mg content(${\varepsilon}_f={\sim}140%$ at 4 mass%). Combined addition of Mg and Cu(MA Al-1.5%Mg-4.0%Cu) is very effective for the occurrence of superplasticity(${\varepsilon}_f$ > 500%). Warm-rolling(at 393-492 K) tends to raise ${\varepsilon}_f$. Lowering the rolling-temperature is effective for increasing the ductility. The effect is rather weak in MA pure Al and MA Al-Mg alloys, but much larger in the MA Al-1.5%Mg-4.0%Cu alloy. Additions of Mg and Cu and warm-rolling of the alloy cause a remarkable reduction in the logarithm of the peak flow stress at low strain rates (${\acute{\varepsilon}}$< ~1/s) and sharpening of microstructure and smoothening of grain boundaries. Additions of Mg and Cu make the strain rate sensitivity(the m value) larger at high strain rates, and the warm-rolling may make the grain boundary sliding easier with less cavitation. Grain boundary facets are observed on the fracture surface when ${\varepsilon}_f$ is large, indicating the operation of grain boundary sliding to a large extent during superplastic deformation.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.176-179
• /
• 1999

The high temperature deformation behaviour of 15vol% SiCp/A16061 composites has been studied in the temperature range of 300-50$0^{\circ}C$ and the strain rate range of 0.1-3.0/sec by torsion test. On he basis of the flow stress data the strain rate sensitivity(m) of the material is evaluated and used for calculating the deformation efficiency(η) [η=2m/(m+1)] A domain of dynamic recrystallization(DRX) could be identified in these maps by using the deformation efficiency. The characteristicvs of these results has been investigated with the help of determining the region of optimum hot working condition.