• Korean Journal of Optics and Photonics
• /
• v.14 no.1
• /
• pp.38-43
• /
• 2003

Fabrication process of strain-induced channel waveguides in $LiNbO_3$ was developed using strain-optic effect and compressional strain due to ~1.4 $\mu\textrm{m}$ surface Mo/Pt metal film. Characterization of the channel waveguides revealed a single transverse and depth mode in both TE and TM polarizations. Measurements showed total insertion loss of 6.2 and 7.7 ㏈/cm for TM and TE polarizations. respectively. Electro-optic intensity modulators with 11 mm long electrode length and 21 $\mu\textrm{m}$ electrode gap at $\lambda$ = 1.15 ${\mu}{\textrm}{m}$have been produced in $LiNbO_3$ substrates using strain-induced channel waveguides. Modulation depth of 100% at $\pi$-radian voltage of 16.1V has been demonstrated. Also, 1$\times$2 on/off power splitters at $\lambda$ = 0.63 $\mu\textrm{m}$ have been produced using strain-induced channel waveguides. On/off voltage of $\pm$ 25V has been demonstrated.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.1
• /
• pp.72-78
• /
• 1998

Polarization mode converters have been produced by utilizing Ti:LiNbO$_{3}$ channel waveguide and strain-optic effect. Shear strain for periodic perturbations of optical channel waveguides and phase matching can be obtained by an evaporated periodic SiO$_{2}$ thin film at 300.deg. C. The electrodes located on the either side of waveguide provide a means to electro-optically tune the wavelength for maximum polarization conversion via the electrooptic effect. The maximum conversion effeciency was observed at 21.deg. C for V=0 and 46.deg. C for V=30V aro the device having 7 .mu.m waveguide wiith and 350 periodic pads. The dependence of the number of pads on conversion efficiency was observed experimentally.fficiency was observed experimentally.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.12
• /
• pp.776-780
• /
• 2015

In this paper, we have studied the effect of mechanical polishing to Ga-polar face for reducing the wafer bowing and strain in free-standing GaN. After the mechanical polishing to Ga-polar face, the bowing of the free-standing GaN substrate significantly decreased with increasing the size of diamond slurry, and eventually changed the bowing direction from concave to convex. Furthermore, the full width at half maximum (FWHM) of high-resolution X-ray diffraction (HR-XRD) were decreased, especially the FWHM of (1 0 2) reflection for $1.0{\mu}m$ size of diamond slurry was significantly decreased from 630 to 203 arcsec. In the case, we confirmed that the compressive strain in Ga-polar face was fully released by Raman measurement.

• Journal of Sensor Science and Technology
• /
• v.10 no.3
• /
• pp.163-172
• /
• 2001

Fiber optic BOTDA (Brillouin Optical Time Domain Analysis) sensor was developed to be able to detect intrusion effect through several ten kilometer optical fiber. Fiber optic BOTDA sensor was constructed with 1 laser diode and 2 electro-optic modulators. The intrusion detection experiment was peformed by the strain inducing set-up installed on an optical table to simulating an intrusion effect. In the result of this experiment, the intrusion effect was well detected as the distance resolution of 3 m through the fiber length of about 4.81 km during 1.5 seconds.

• Korean Journal of Optics and Photonics
• /
• v.17 no.5
• /
• pp.430-436
• /
• 2006

Polarization-independent $Ti:LiNbO_3\;2{\times}2$ optical add/drop multiplexer for the 1550nm wavelength region is fabricated. The device consists of two input waveguides, two polarization beam splitters. two polarization conversion/electrooptic tuning waveguide sections, and two output waveguides. The single mode channel waveguides for both TE and TM polarizations are fabricated on a x-cut $Ti:LiNbO_3$substrate by Ti diffusion. Spectral section is based on phase-matched polarization conversion due to shear strain induced by a thick $SiO_2$ grating overlay film. An applied voltage tunes the device by changing the waveguide birefringence, hence the optical wavelength at which most efficient polarization conversion occurs. Tuning rate of 0.094nm/V with a maximum range of 17nm has been obtained. The nearest side-lobe is about 8.2dB. The FWHM is 3.72nm.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.486-489
• /
• 2004

In this paper, we try to detect the peel out effect and find the strain difference between the main structure and retrofitting patch material when they separate from each other. In the experiment, two fiber optic Bragg grating sensors are applied to the main concrete structure and the patching material separately at the same position. The sensors show coincident behaviors at the initial loading, but different behaviors after a certain load. The test results show the possibility of optical fiber sensor monitoring of beam structures retrofitted by the composite patches.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.5
• /
• pp.426-431
• /
• 2019

In this study, we report the effect of pre-treatment of alpha-$Ga_2O_3$ grown on a sapphire substrate by halide vapor phase epitaxy (HVPE). During the pre-treatment process, 10 sccm of GaCl gas was injected to the sapphire substrate at $470^{\circ}C$. The surface morphologies of the alpha-$Ga_2O_3$ layers grown with various pre-treatment time (3, 5, and 10 min) were flat and crack-free. The transmittance of the alpha-$Ga_2O_3$ epi-layers was measured to analyze their optical properties. The transmittance was over 80% within the range of visible light. The strain in the alpha-$Ga_2O_3$ grown with a pre-treat 5 min was measured, and was found to be close to the theoretical XRD peak position. This can be explained by the reduction of strain having caused a lattice mismatch between the alpha-$Ga_2O_3$ layer and sapphire substrate. The calculated dislocation density of the screw and edge were $2.5{\times}10^5cm^{-2}$ and $8.8{\times}10^9cm^{-2}$, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.11
• /
• pp.1048-1055
• /
• 2005

The formula to calculate a variation of optical path length of single crystal by the electric field was derived by this study. The formula was applied to $Bi_{12}SiO_{20}$ single crystal. The results are as follows. In case of the applied electric field in the body diagonal direction and the passing light along the same direction, the variation of optical path length had the largest value. The symmetry of the space distribution of optical path length satisfied $E3C_2\;8C_3$, the set of elements of the symmetry of $Bi_{12}SiO_{20}$ single crystal. The property which gave the largest influence to the variation of optical path length is the strain of length by the Inverse piezoelectric effect. The second influence, is the variation of the refractive index by the electro-optic effect. The variation of optical path length by the inverse piezoelectric effect and by the electro-optic effect have a reverse sign each other.

• Journal of Magnetics
• /
• v.2 no.2
• /
• pp.58-66
• /
• 1997

Recently, artificially modulated magnetic multilayer materials, for examples giant magnetoresistant magnetic head materials and magneto-optic recording materials in the wavelength of a blue laser beam, attract great attention in the electronics industry due to their unique properties derived from the modulated multilayer structure. Since the multilayer structure as well as amorphous structure, is non-equilibrium state in terms of free energy, an assessment of the thermal staibility in the multilayer structure is crucially importnat both for basic research and applications. In this review paper, effective microscopic interdiffusion process in the two dimensional multilayer structure will be described in terms of steep concentration gradient effect, strain effect and magnetic transition effect.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.416-420
• /
• 2002

This Paper describes a matched-filter type strain sensor system using optical fiber Bragg grating (FBG) sensor. Matched-filter type uses another wavelength-matched FBG filter to track wavelength shift in the FBG sensor. Filter FBG is attached on a fiber stretcher and stretched by PZT actuator. To overcome the nonlinearity and hysteresis of the PZT actuator that degrades system accuracy, a string resonator which can measure an absolute strain is employed. And the effect of vibration modes on string resonator is investigated particularly regarding its sensitivity and stability.