• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.3 s.108
• /
• pp.226-232
• /
• 2006

This paper presents the dynamic analysis of an impulsively forced rotating cantilever beam with rigid body motion. The transient response induced by the impulsive force and the rigid body motion of the beam are calculated using hybrid deformation variable modeling with the Rayleigh-Ritz assumed mode methods. The stiffness variation effect due to the rigid body motion of the beam is considered in this study Also, the effects of the impulsive force position and the angular velocity on the transient responses of the beam are investigated through numerical works.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.5
• /
• pp.437-443
• /
• 2012

In this paper, the hybrid method to identify the exciting forces and radiated noise generated from the reciprocating compressor was presented. In order to identify the exciting force, both the acceleration data measured at the compressor shell and numerical finite element model for the full set of compressor were used simultaneously. Applying the identified exciting forces to the numerical model, the velocity responses of all nodes at the shell were predicted. Finally the radiated noises from the vibrating shell were predicted by using the direct boundary element acoustic analysis. For precise numerical modeling, the stiffness of rubber mounts and body springs were identified experimentally from the natural frequencies measured by impact testing. The error of over-all sound pressure level between predicted noise and measured noise was about 2.9 dB.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.9
• /
• pp.109-121
• /
• 2000

A simplified modeling approach of free vibration for occupied car seats was demonstrated to be feasible. The model consisting of interconnected masses springs and dampers was initially broken down into subsystems and experiments conducted to determine approximate values for model parameters. Which were each stiffness and damping value. Nonlinear equations of motion were derived and model parameters obtained in experiments were applied to these equations. A mathematical model of free vibration for car seat and mannequin system was built with 7 degrees of freedom. in order to calculate natural frequencies and the corresponding mode shapes. linear equations of motion were obtained through linearization. In order to explore the effects of each model parameter free vibration analysis were preformed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.04a
• /
• pp.279-284
• /
• 1992

This paper presents the theoretical development and qualitiative evaluation of a new concept in the mathematical modeling of dynamicstructures. We use both test data and analytical approximations to identify the parameters of an incomplete model. The model has the capability of prodicting the response of the points of interest on the structure over the frequency range of interest and can be used to predict the changes in natural frequencies and normal modes due to structural changes. The theory was tested by running simulated tests on a relatively simple structure, identifying the parameters of the incomplete model, and using this model to predict the effects on frequency and mode shapes of several mass and stiffness changes. The conditions of the test were varied by selecting different numbers of points of meansurement, varying the frequency range, and by including assumed measurement error. It is recommended that the theroetical development be continued and that applications to more complex structures be carried out in order todevelop a better understanding of the limitations and capabilites of the method. A successful, more definitive evaluation could lead to immediate practical applications.

• Coupled systems mechanics
• /
• v.5 no.2
• /
• pp.157-190
• /
• 2016

This paper deals with frequency analysis of Euler-Bernoulli beams carrying an arbitrary number of Kelvin-Voigt viscoelastic dampers, subjected to harmonic loads. Multiple external/internal dampers occurring at the same position along the beam axis, modeling external damping devices and internal damping due to damage or imperfect connections, are considered. The challenge is to handle simultaneous discontinuities of the response, in particular bending-moment/rotation discontinuities at the location of external/internal rotational dampers, shear-force/deflection discontinuities at the location of external/internal translational dampers. Following a generalized function approach, the paper will show that exact closed-form expressions of the frequency response under point/polynomial loads can readily be derived, for any number of dampers. Also, the exact dynamic stiffness matrix and load vector of the beam will be built in a closed analytical form, to be used in a standard assemblage procedure for exact frequency response analysis of frames.

• Steel and Composite Structures
• /
• v.22 no.1
• /
• pp.79-89
• /
• 2016

Cold formed steel shear panel is one of the main components to bearing lateral load in low and mid-rise cold formed steel structures. This paper uses finite element analysis to evaluate the stiffness, strength and failure mode at cold formed steel shear panels whit steel sheathing and nonlinear connections that are under monotonic loading. Two finite element models based on two experimental model whit different failure modes is constructed and verified. It includes analytical studies that investigate the effects of studs and steel sheathing thickness changes, fasteners spacing at panel edges, one or two sides steel sheathing and height-width ratio of wall on the lateral load capacity. Dominant failure modes include buckling of steel sheet, local buckling in boundary studs and sheet unzipping in the bottom half of the wall.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.1
• /
• pp.88-93
• /
• 2004

In general, a fundamental structural design consideration for an automobile is the overall dynamic behavior in bending and torsion. Dynamic behavior of the automobile are mainly influenced by the structural stiffness of B.I.W.(body-in-white) and the physical property of trim components. In this paper, the modeling techniques for various trim components of middle-sized bus are presented, and the dynamic effects of the trim components on the vibration characteristics of the bus are investigated. The $1^{st}$ torsional frequency is decreased by attaching windshield and backlite to the B.I.W., but the $1^{st}$ vertical bending frequency and the $1^{st}$ lateral bending frequency are increased. The natural frequencies of the bus are decreased by attaching doors and windows. And also, the natural frequencies of the bus are large decreased by attaching seats, instrument panel etc. The study shows that the dynamic characteristics of the bus can be effectively predicted in the initial design stage.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.371-376
• /
• 1999

Stick-slip friction is present to some degree in almost all actuators and mechanisms and is often responsible for performance limitations. Simulation of stick-slip friction is difficult because of strongly nonlinear behavior in the vicinity of zero velocity. A straightforward method for representing and simulating friction effects is presented. True zero velocity sticking is represented without equation reformulation or the introduction of numerical stiffness problems. Stick-slip motion is investigated experimentally, and the fundamental characteristics of the stick-slip motion are clarified. Based on these experimental results, the characteristics of static in the period of stick and kinetic friction in the period of slip are studied concretely so as to clarify the stick-slip process.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.612-617
• /
• 2008

In this present work, trimmed surface analysis for the 2D elasticity problem is presented. The main benefit of the proposed method is that no additional modeling for analysis of a trimmed surface is necessary. As the first attempt to deal with a trimmed surface in spline FEM, the information of the trimming curve and trimmed surface exported from CAD system is directly utilized for analysis. For this, trimmed elements are searched through employing projection scheme. For the integration of the trimmed elements, NURBSenhanced integration scheme which is used in NEFEM is adopted. The quadtree refinement of integration cell is performed for the complicated trimmed cases. The information of trimming curve is used for obtaining integration points as well as constructing stiffness matrix. The robustness and effectiveness of the proposed method are investigated by presenting various numerical examples.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1672-1677
• /
• 2003

In this paper, the spectral element model is derived for the vibration and stability analyses of an axially moving viscoelastic beam subjected to axial tension. The viscoelastic material is represented by using a one-dimensional constitutive equation of hereditary integral type. The accuracy of the present spectral element model is first verified by comparing the eigenvalues obtained by the present spectral element model-based SEM with those obtained by the exact theory and the conventional FEM. The effects of viscoelasticity on the vibration and stability of an example moving viscoelastic beam are numerically investigated.