• Steel and Composite Structures
• /
• v.42 no.4
• /
• pp.447-458
• /
• 2022

Cold-formed steel (CFS) sections are thin-walled, therefore, more susceptible to different types of geometric imperfections. Global type of geometric imperfections has a significant impact on the load-carrying capacity of flexural members. This paper reports an experimental study that discusses the influence of global imperfections on the flexural response of CFS built-up I-beams composed of two lipped channels, with simply supported ends, under four-point loading. Global imperfections of magnitude over eight times the maximum permissible ones were induced in the specimens, leading to their distress. Using various simple stiffening schemes, the capacity and stiffness of the distressed specimens were improvised. The performance comparisons were made based on the maximum loads resisted, flexural stiffnesses offered, and failure modes experienced by the specimens. As experimental data on such distressed specimens are currently lacking in the literature, the test results of the present study will provide the necessary data needed by future researchers to numerically extend this study further, which will help in the development of necessary design guidelines for the same. The stiffening schemes significantly improved the structural efficiency of distressed specimens in terms of strength and stiffness, by over 60%. As a result, an effective and time-saving solution to such realistic structural engineering problems is given.

• Journal of the Korea Concrete Institute
• /
• v.22 no.6
• /
• pp.859-866
• /
• 2010

To overcome weak and brittle tensile characteristics of concrete, many studies have been conducted on fiber reinforced concrete (FRC). Recently, high performance fiber reinforced cementitious composites (HPFRCC), which shows strain hardening behavior, has been actively investigated. However, most of the studies focused on the material behavior of HPFRCC itself. Only a few studies have been conducted on the tensile behavior of HPFRCC with steel reinforcement. Therefore, a tension stiffening test for HPFRCC members has been conducted in this study in order to investigate the effect of a reinforcing bar on the tensile behavior of HPFRCC. Tensile stress-strain relationship of HPFRCC has been derived from the tests. The HPFRCC resisted tensile stress continuously from the first cracking to the yield of reinforcing bar. Through the comparison with the tensile behavior of HPFRCC members without a reinforcement, it was shown the tensile strength and capacity of HPFRCC were reduced due to the combined effect of the high shrinkage of HPFRCC, restraining effect of steel reinforcement, and the strain hardening behavior of HPFRCC. It is expected that the tension stiffening test results can be useful for an application of HPFRCC with steel reinforcement as structural members.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.12
• /
• pp.1931-1936
• /
• 2004

In this paper, modeling methods for the structural dynamic analysis employing single reference frame are presented and their modal and transient analysis results are compared. The geometric stiffening effects often occur when structures undergo large overall motion. These effects were considered in several structural previous modeling methods but the role of reference frame has never been scrutinized. In this study, modeling methods employing single reference frame are presented, and their numerical results are compared. The results show that discrepancy between the two modeling methods increases as the eccentricity of the structural system and the magnitude of the large overall motion increase.

• Steel and Composite Structures
• /
• v.18 no.4
• /
• pp.1023-1044
• /
• 2015

Concrete-filled tubes (CFT), formed by an outer steel tube filled with plain or reinforced concrete inside, have been increasingly used these recent decades as columns or beam-columns, especially for tall buildings in seismic areas due to their excellent structural response. This improved behavior is derived from the effect of confinement provided by the tube, since the compressive strength of concrete increases when being subjected to hydrostatic pressure. In circular CFTs under compression, the whole tube is uniformly tensioned due to the radial expansion of concrete. Contrarily, in rectangular and square-shaped CFTs, the lateral flanges become subjected to in-plane bending derived from this volumetric expansion, and this fact implies a reduction of the confinement effect of the core. This study presents a numerical analysis of different configurations of CFT stub columns with inner stiffening plates, limited to the study of the influence of these plates on the compressive behavior without eccentricity. The final purpose is to evaluate the efficiency in terms of strength and ductility of introducing stiffeners into circular and square CFT sections under large deformation axial loading.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1991.10a
• /
• pp.23-28
• /
• 1991

A simple, yet effective, material model of concrete is presented in this paper. Based on the orthotropic model in which the assumption of orthogonal principal strain axes is used, the incremental stress-strain relation of concrete is defined in the biaxial stress condition and the rotating crack model is adopted to represent realistically the change of the crack direction according to the different loading pad after cracking. Numerical results obtained from the finite element analysis are compared favourably with the available experimental data. By the parametric study, moreover, it was found that He most important factor in the structural behavior when the reinforced concrete structure is subjected to the dominent shear forces is the tension stiffening effect. The influences of the tension stiffening effect remarkably appears as the steel ratio decreases.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.44 no.3
• /
• pp.73-84
• /
• 2002

Nominal shear strength of concrete beam is the combined strength of concrete shear strength and steel shear strength in current design code. But Torsional moment strength of concrete is neglected in calculation of the nominal torsional moment strength of reinforced concrete beam in current revised code. Tensile stress of concrete strut between cracks is still in effect due to tension stiffening effect. But the tensile stresses of concrete after cracking are neglected in bending and torsion in design. The torsional behavior is similar to the shear behavior in mechanics. Therefore the torsional moment strength of concrete should be concluded to the nominal torsional moment strength of reinforced concrete beam. To verify the validity of the proposed model, the nominal torsional moment strengths according to CEB, two ACI codes(89, 99) and proposed model are compared to experimental torsional strengths of 55 test specimens found in literature. The nominal torsional moment strengths by the proposed model show the best results.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.1 no.1
• /
• pp.189-200
• /
• 1998

본 연구에서는 얇은 마레이징강으로 제작된 천마 연소관에 브라켓이 용접되어 비행 날개를 볼트로 체결한 경우, 압력과 공력하중에 의해 브라켓 부위에 집중되는 응력의 해석기법을 정립하기 위하여 선형해석과 기하학적 비선형 해석을 수행하였다. 높은 압력에 의해 발생한 얇은 연소관의 면내 응력이 구조물의 강성을 증가시키는 응력의 강성보강효과(stress stiffening effect)를 고려한 기하학적 비선형 해석을 수행하여 선형해석 결과와 비교하였으며, 압력과 공력하중을 동시에 적용할 수 있는 복합하중시험기로 변형률을 측정하여 해석치의 정확성을 검토하였다. 얇은 연소관에 압력과 공력하중이 동시에 작용하는 경우는 응력의 강성보강효과를 고려한 기하학적 비선형 해석을 수행함으로써 보다 정확한 응력을 구할 수 있다는 결론을 얻었다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04a
• /
• pp.321-326
• /
• 1998

Shear failure of reinforced concrete beams is serious problem due to sudden brittle failure and many experimental results proved that size effect in shear behavior is an important feature of reinforced concrete members. For this reason, the structural safety of the reinforced concrete beams for shear has been checked by applying empirical design formula, which includes the size-effect, derived from experimental data. However, as the sizes of reinforced concrete members become extremely large, experiments sometimes become very difficult so that the formula or the experimental data could not be obtained and size-effect analyses of shear behavior become significant. In this study, size-effect analysis of shear behavior in reinforced concrete beams is performed by modeling tension stiffening/shear stiffening on reinforced concrete and the tension softening/shear softening on plain concrete. Then, the influences of models in the size-effect analyses of shear behavior in reinforced concrete beams are analyzed.

• Structural Engineering and Mechanics
• /
• v.6 no.8
• /
• pp.883-899
• /
• 1998

The strength, deformation and buckling of a large engineering structure consisting of four ellipsoidal shells, two cylindrical shells with stiffening ribs and large holes, one conical shell and three pairs of large flanges under external pressure, self weight and heat sinks have been analysed by using two kinds of five different finite elements - four assumed displacement finite elements (shell element with curved surfaces, axisymmetric conical shell element with variable thickness, three dimensional eccentric beam element, axisymmetric solid revolutionary element) and an assumed stress hybrid element (a 3-dimensional special element developed by authors). The compatibility between different elements is enforced. The strength analyses of the top cover and the main vessel are described in the paper.

• Structural Engineering and Mechanics
• /
• v.31 no.3
• /
• pp.277-296
• /
• 2009

The paper investigates the dynamic behaviour of stiffened panels. The coupled differential equations for eccentric stiffening configuration are first derived. Then a semi-analytical procedure for dynamic analysis of stiffened panels is presented. Unlike finite element or finite strip methods, where the plate is discretized into a set of elements or strips, the plate in this procedure is treated as a single element. The potential energy of the structure is first expressed in terms generalized functions that describe the longitudinal and transverse displacement profiles. The resulting non-linear strain energy functions are then transformed into unconstrained optimization problem in which mathematical programming techniques are employed to determine the magnitude of the lowest natural frequency and the associated mode shape for pre-selected plate/stiffener geometric parameters. The described procedure is verified with other numerical methods for several stiffened panels. Results are then presented showing the variation of the natural frequency with plate/stiffener geometric parameters for various stiffening configurations.