• Proceedings of the KIEE Conference
• /
• 1998.11a
• /
• pp.304-307
• /
• 1998

High speed railway is under construction from Seoul to Pusan. A traveling train is large single phase load that consumes 14MW power in feeding system of high speed railroad. In this paper, measurement scheme and method of power system harmonics which are generated from those loads in railroad supply system are described. This measurement scheme will be used as a first step to pave a way to power quality management due to harmonic distortion by the highspeed rail way.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.9
• /
• pp.2744-2751
• /
• 1996

In case of limited power supply, a rotating shaft system may not reach its operating speed that is greater than its critical speed, but the speed oscillates with small ampllitude near critical speed. As a result, it is considered that the operating mode plays an important role in the smooth start of machines. In order to investigate the dynamic behaviors of the rotating shaft system at the beginning stage, one has derived the equations of motion whose degrees of freedom is three, two translations and one rotation. The simultaneous differential equations are numerically solved by using runge-Kutta method, and thus the small time step length could be required corresponding to the stability of solution. Three types of operating modes dependent upon the driving torque rate have been numerically investigated according to the maximum displacement of shaft center. The first type of relation is linear, the second type is composed of two linear curves recommended by machine manufacturer, and the last one is the proposed torque curve reflecting the frequency response curve of one degree of freedom system. For the second type of modes, it is found that the optimal range of intermediate speed to the critical speed lies between 0.8 and 0.9. In addition to that, the maximum displacement can be reduced more if the third type of mode is utilized.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.2207-2212
• /
• 2008

The next generation of Korean high-speed train under development will be designed for the maximum operating speed of 350km/h and maximum speed of 400km/h. This high-speed operation may cause the noise and vibration problems around tunnel exit due to the higher micro-pressure wave than present level. In this study, the nose shape optimization was conducted for the countermeasure against these problems. Axi-symmetric solver was used for numerical simulation, and response surface was used for efficiency of optimization process. Also the multi-step optimization was conducted to find out more accurate optimal shape. Through these analysis and optimization, it was found out that the optimal nose shapes for minimization of micro-pressure wave are definitely different along the nose length variation. And the mechanism of micro-pressure wave reduction was closely investigated by the analysis of generation process of compression wave in tunnel. The results are expected to be used as design guideline for performance improvement of the next generatin of Korean high-speed train.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.106-108
• /
• 2008

This paper deals with the design for speed controller to drive PMSM by matrix converter without DC-link circuit as the power conversion system of AC servo motor drive. To design the speed controller of PMSM drive, the closed-loop transfer function of speed controller is calculated and then the frequency-domain response characteristics are analyzed by bode plot using Matlab. Based on the results by bode plot, the speed control gains are determined. As the real effects of controller designed in the frequency-domain display in the time-domain, the performance of speed controller is confirmed by the step response of speed controller. The design examples are shown and its validity of the design method mentioned in the paper is verified through PSIM simulation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.529-535
• /
• 2018

The range extender vehicle runs on a mechanism that allows the small power generation engine to start in the most efficient specific operating range to charge the battery and extend the mileage. In this study, we developed a step motor type intake air supply system that replaces existing throttle body system to develop a simple low cost control logic system. The system was applied to the existing base engine, and in order to improve the performance by increasing the amount of intake air, the effect of changing the length of the intake and exhaust manifold was experimentally examined. As a result, the Type B intake air control actuator operated by one step motor showed higher performance than the Type A in all the operation region, but the performance was lower than that of the base engine due to the increase of flow resistance. To improve this, it was confirmed that the engine performance was improved at both speeds of 2200rpm and 4300rpm when the 140mm adapter was installed in the intake manifold and when the newly designed 70mm exhaust manifold was applied. Through this process, high - precision operation control was realized by connecting the generator load to the optimized engine for the range extender electric vehicle. Experimental results showed that the speed change rate was within ${\pm}2.5%$ at 2200rpm in 1st stage and 4300rpm in 2nd stage and the speed follow-up result of 610 rpm/s was obtained when the speed was increased from 2200rpm to 4300rpm.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.1
• /
• pp.119-130
• /
• 1996

This paper is the part I of the full study about improved structure of fully interconnected ATM switch to develop the small sized switch element and practical implemention of switch network. This part I paper describes about proposed switch structure, performance evaluations and some of considerations to practical implementation. The proposed structure is constructed of two step buffering scheme in a filtered multiplexer. First step buffering is carried out by small sized dedicated buffers located at each input port. And second step buffering is provided by a large sized common buffer at the output port. To control bursty traffic, we use speed up factor in multiplexing and priority polling according to the levels of buffer occupancy. Proposed structure was evaluated by computer simulation with two evaluation points. One is comparision of multiplexing discipline between hub polling and priority polling. The ogher is overall which should be considered to improve the practical implementation.

• Proceedings of the IEEK Conference
• /
• 2000.06b
• /
• pp.201-204
• /
• 2000

In this paper, an A/D converter is implemented to obtain 8bit resolution at a conversion rate of 10Msample/s. This architecture is proposed using the 2-step architecture for high speed conversion rate. It is consisted of sample/hold circuit, low power comparator, voltage reference circuit and DAC of binary weighted capacitor array. Proposed A/D converter is designed using 0.2$\mu\textrm{m}$ CMOS technology. The SNR is 45.3dB at a sampling rate of 10MHz with 1.95MHz sine input signal. When an 8bit 10Msample/s A/D converter is simulated, the Differential Nonlinearity / Integral Nonlinearity (DNL/ INL) error are ${\pm}$1 / ${\pm}$2 LSB, respectively. The power consumption is 13㎽ at single +2.5V supply voltage.

• Proceedings of the KIEE Conference
• /
• 1997.07f
• /
• pp.2101-2103
• /
• 1997

In this paper, micro step driving method is used for a high performance motion control and minimizing of vibration in a industrial X-Y table. By using a mathmetical analysis method of 2 phase Hybrid-type step motor, each phase current can be optimized about unit speed and torque. We can improve the electrical and mechnical driving charicteristic of machine by applying this proposed driver to the real plant using microprocessor.

• 전기의세계
• /
• v.24 no.2
• /
• pp.78-83
• /
• 1975

There are many studies recently, on a wound rotor induction motor operation as synchronous rotating speed, and such an induction motor is so called an induction synchronous motor. In above desciption the region of pull into-step that the wound rotor induction motor as a synchronous motor has not been calculated. This paper deals with such a region. Generally, induction synchronous motor is different from a synchronous motor in many respects. In considering these respects, characteristic equations of motion for this motor are induced adoption small signal linearization, continuous quasili-nearization and state variable grouping technique. For pulling-into-step of Induction Synchronous Motor, we first analyze these equations with digital computer and compare the former with datas calculated by motor experimentation.

• Proceedings of the Korea Multimedia Society Conference
• /
• 2001.11a
• /
• pp.46-50
• /
• 2001

Adaptive signal processing is used to acoustic echo canceller. adaptive noise canceller and adaptive algorithm among adaptive algorithms is mainly used because the structure is simple and computa LMS algorithm has trade-off between the converge speed and the steady state error. In this paper, step-size of adaptive algorithm is varied with orthogonality Principles of optimal filter to get fasts though small steady state error. Time varying step-size is determined proportional to the maximum vector of LMS algorithm. As results of simulations, the adaptive algorithm with proposed time-v compared with conventional ones.