• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.120-123
• /
• 1999

The precision cold forging process for steering yoke of automobile has been analysed by using rigid-plastic finite element analysis code DEFORM-3D Also the experiment has been performed through the optimized process. Until now steering yoke has been largely manufactured by hot forging or welding of forged head and shaft parts because of technical difficulty. the study has shown successful results of the precision cold forging through the proper selection of the process.

• Proceedings of the IEEK Conference
• /
• 2007.07a
• /
• pp.149-150
• /
• 2007

By adding Gyro sensor to support the steering wheel angle sensor, an improved functional DR solution is proposed in this paper The proposed angle data algorism is developed based on the steering wheel with Gyro sensor for DR. The Gyro sensor support the error of steering wheel sensor to improve the angle data for the DR algorism.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.06a
• /
• pp.307-308
• /
• 2009

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.2
• /
• pp.57-66
• /
• 2009

In this paper, the steering characteristics of tracked vehicles are studied for the improvement of steering performance. The important design factor of military vehicles is high mobility. It is influenced by weight of a vehicle, engine capacity, power-train, and steering system. The military vehicle, which is equipped with caterpillar, has unique steering characteristics and is quite different from that of a wheeled vehicle. The steering of tracked vehicles is operated in the power pack due to different speeds of both sprockets. Under cornering conditions, power split and power regeneration are happened in the power pack. In case of power regeneration, power is transferred outside track after adding engine power and power inputted inside track from the ground. However, excessive power regeneration is transferred in the power pack. It damages mechanical elements. Therefore, it is necessary to analyze the steering system and check mentioned problem above. In this study, the detailed dynamic model of steering system is presented, which includes slippage between track and roadwheel, inertia force, and inertia moment. Finally, our model is compared with the Kitano model and we verified the validity of the model.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.2
• /
• pp.95-101
• /
• 2015

In this paper, we develop a sliding mode control for steering wheel angle control based on torque overlay in order to resolve the problem of previous methods for Electric Power Steering (EPS) systems in the Lane Keeping System (LKS) of autonomous vehicles. For the controller design, we propose a 2nd order model of the electric power steering system in an autonomous LKS. The desired state model is designed to prevent a rapid change of the steering wheel angle. The sliding mode steering wheel angle controller is developed for the robustness of the disturbance. Since the proposed method is designed based on torque overlay, torque integration with basic functions of the EPS system for the steering wheel angle control is available for the driver's convenience. The performance of the proposed method was validated via experiments.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.9
• /
• pp.105-111
• /
• 1999

The paper presents development of a Hardware-In-the-Loop simulation (HILS) system for the purpose of testing performance, stability, and reliability of an electronic power steering system(EPS). In order to realistically test an EPS by the proposed HILS apparatus, a simulated uniaxial dynamic rack force is applied physically to the EPS hardware by a pnumatic actuator. An EPS hardware is composed of steering wheel &column, a rack & pinion mechanism, andas motor-driven power steering system. A command signal for a pneumatic rack-force actuator is generated from the vehicle handling lumped parameter dynamic model 9software) that is simulated in real time by using a very fast digital signal processor. The inputs to the real-time vehicle dynamic simulation model are a constant vehicle forward speed and from wheel steering angles driven through a steering system by a driver. The output from a real-time simulation model is an electric signal that is proportional to the uniaxial rack force. The vehicle handling lumped parameter dynamic model is validated by a fully nonlinear constrained multibody vehicle dynamic model. The HILS system simulation results sow that the proposed HILS system may be used to realistically test the performance stability , and reliability of an electronic power steering system is a repeated way.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.3
• /
• pp.66-78
• /
• 1995

In this paper, we address vehicle modeling and dynamic analysis of four wheel steering systems (4WS). 4WS is one of the devices used for the improvement of vehicle maneuverability and stability. All research done here is based on a production vehicle from a manufacturer. To study actual system response, a three dimensional, full vehicle model was created. In past research of this type, simple, two dimensional, bicycle vehicle models were typically used. First, we modelled and performed a dynamic analysis on a conventional two wheel steering(2WS) vehicle. The modeling and analysis for this model and subsequent 4WS vehicles were performed using ADAMS(Automatic Dynamic Analysis of Mechanical Systems) software. After the original vehicle model was verified with actual experiment results, the rear steering mechanism for the 4WS vehicle was modelled and the rear suspension was changed to McPherson-type forming a four wheel independent suspension system. Three different 4WS systems were analyzed. The first system applied a mechanical linkage between the front and rear steering mechanisms. The second and third systems used, simple control logic based on the speed and yaw rate of the vehicle. 4WS vehicle proved dynamic results through double lane change test.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.22 no.5
• /
• pp.597-602
• /
• 2012

In this paper, a manual and automatic steering system for electric vehicles capable of manned and unmanned driving is proposed. The automatic steering systems, EPS, MDPS, used in conventional engine based car includes the problem of handle lock phenomenon while driving of overloading, therefore it has a drawback to apply to manned and unmanned electric vehicles. By using electronic clutch and pulleys, the proposed manual and automatic steering mechanism was designed so that it is possible to convert from manual to automatic steering mode. To experiment the performance of the proposed steering system, we made an experimental setup of an electric vehicle. We confirmed that the proposed manual and automatic steering system was useful for manned and unmanned electric vehicles.

• Journal of Drive and Control
• /
• v.17 no.4
• /
• pp.113-124
• /
• 2020

Most of the work of construction equipment and agricultural machinery is done in off-road conditions. Autonomous driving required in these conditions uses GPS sensors, and PID controllers to control their speed and position. The hydrostatic steering, which is composed of a PSU, hydraulic hoses, and cylinders, rather than a mechanical coupling is used in these equipments. The PSU plays a key role in hydrostatic steering. Precise control of the position under various conditions requires detailed behavioral analysis of the basic components and operation. Two Gerotor PSU is now a commonly used safer option. The components of the PSU can be divided into mechanical and hydraulic actuating elements by its behavior. Since the system is combined by mechanical and hydraulic elements, the modelings are performed using Amesim, which is one of the most effective for the multi-domain dynamic system analysis. To confirm the validity of the model, input torque and pressures are checked with varying steering speed. The opening and the steering speed of normal and newly designed control valve set is investigated with the effect of centering spring force and friction. Finally, simulation results with fully detailed model with two gerotors are analyzed and compared with simple model.

• International journal of advanced smart convergence
• /
• v.11 no.2
• /
• pp.219-225
• /
• 2022

Recently, the popularization of personal mobility(PM) has made it possible to see many electric scooters. The energy source of personal transportation used by the general public and the disabled can be seen as environmentally friendly as electricity. Personal transportation means are divided into small electric vehicles because they use electric energy, and they are being treated as new models by automobile manufacturers in each country and spurring development. On the other hand, personal transportation means may cause various types of traffic accidents as they travel between roads and a human walk. In order to prevent such accidents, it is judged that the enactment of laws on the establishment of specifications for electric scooters, which are personal transportation means, and the method of restricting road operation should be given priority. The electric scooter is basically different from the conventional vehicle. The steering shaft of the steering system applied to the electric scooter one to two is possible. 1 to 2 the front-wheel under the steering column is used. It is classified according to the number of wheel installed at the electric scooter is the vehicle body into 2 wheel - electric scooter, and 3 wheel - electric scooter and 4 wheel - electric scooter. In this study, we propose a steering shaft design model that can be applied to an electric scooter, one of personal transportation means. A design model for 1-shaft steering and 2-shafts steering that can be applied to electric scooters is proposed. In addition, we have produced the prototypes for the commercialization of the proposed models, and reviewed the pros and cons of the manufactured prototypes and models.