• The KIPS Transactions:PartC
• /
• v.9C no.6
• /
• pp.847-856
• /
• 2002

Cellular network applications are growing drastically and this requires a fast and efficient transport method between the base station and the mobile switching center. One possible solution is to use ATM links. The low data rate and small-sized packets in the typical cellular applications imply that significant amount of link bandwidth would be wasted, if this small sized packet is carried by one ATM cell. For efficient operation for such cellular and low bit rate applications, a new type of ATM Adaptation Layer, AAL Type 2, has been proposed. In this paper, the principles of AAL Type 2 are briefly described along with the introduction of other alternatives which have formed the basis for this new AAL. The result from the simulation to study the performance of the AAL Type 2 is discussed from the view point of packet delay and ATM cell use efficiency. Due to the variable size of packets in this application, the fairness issue in serving variable sized packets is also discussed along with the effect of fair queueing algorithm implemented at AAL Type 2.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.6
• /
• pp.469-477
• /
• 2003

This paper proposes a Carrier-Rotation (CR) PWM technique that is a new solution for the voltage unbalancing problem of flying capacitors in the Flying Capacitor Multi-level Inverter (FCMI). The proposed technique equalizes the utilization of phase leg voltage redundancies corresponding to the charging and the discharging state of individual flying capacitors during each switching period of all the switches. Therefore, the charging and the discharging quantity of flying capacitors are equal, which makes the average variation of flying capacitor voltages become zero and keeps their voltage stable during minimum specified period. It also has the reduced harmonic contents of output voltage and the same switch utilization since all the carrier signals are in phase and the switching frequency of each switch is identical. The proposed technique is analyzed precisely in flying capacitor 3-level inverter and then it has expanded to the FCMI (N-level, N>3). Experimental results on the laboratory prototype flying capacitor 3-level inverter confirm the validity of the proposed technique.

• The Transactions of the Korea Information Processing Society
• /
• v.7 no.11S
• /
• pp.3684-3693
• /
• 2000

In this paper, performance of a nonblocking high speed packet switch with switching capacity m which adopts a dynamic priority control function (DPCF) of a threshold- based Bernoulli priority jump (TBPJ) scheme is considered. Each input queue has two separate buffers with different sizes for two classes of traffics, delay-sensitive and loss-sensitive traffics, and adopts a TBPJ scheme that is a general state-dependent Bernoulli scheduling scheme. Under the TBP] scheme, a head packet of the delay-sensitive traffic buffer goes into the loss -sensitive traffic buffer with Hernoulli probability p according to systems states that represent the buffer thresholds and the number of packets waiting for scheduling. Performance analysis shows that TBPJ scheme obtains large performance build-up for the delay-sensitive traffic without performance degradation for the loss-sensitive traffic. In addition to, TBP] scheme shows better performance than that of HOL scheme.

• Journal of Internet Computing and Services
• /
• v.7 no.2
• /
• pp.93-102
• /
• 2006

Traditionally, diffusion of telecommunications services has been considerably affected by presence of critical mass and network externalities, and thus shown the so-called late take-off phenomenon. However, as telecommunications network evolves from circuit switching to packet switching, enabling diverse new services such as Internet access, Internet banking and web hosting, it seems this traditional diffusion patterns are changing. By comparing diffusion of the packet-based services with those of circuit-based services and durable goods, we have found the late take-off phenomenon is not involved in diffusion of newly introduced the packet-based services. Moreover, we concluded diffusion of the packet-based services is much faster than that of durable goods, thus showing early take-off phenomenon. Based on this empirical result, we suggest Telcos and ISPs should pay as much attention to the growth state as the introduction stage in order for their packet-based services to be successful in the markets.

• Current Optics and Photonics
• /
• v.3 no.1
• /
• pp.66-71
• /
• 2019

Application of liquid crystal (LC) materials to a flexible device is challenging because the bending of LC displays easily causes change in thickness of the LC layer and orientation of LCs, resulting in deterioration in a displayed image quality. In this work, we demonstrate a prototype device combining a flexible polymer substrate and an optically isotropic LC-polymer composite in which the device consists of interdigitated in-plane switching electrodes deposited on a flexible colorless polyimide substrate and the composite consisting of nano-sized LC droplets in a polymer matrix. The device can keep good electro-optic characteristics even when it is in a bending state because the LC orientation is not disturbed in both voltage-off and -on states. The proposed device shows a high potential to be applicable for future flexible LC devices.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.2
• /
• pp.123-128
• /
• 2022

The torque of the SRM((Switched Reluctance Motor)) is proportional to the inductance slope, so it has a non-linear torque characteristic, and has a disadvantage in that the torque pulsation is large and noise is severe. In particular, the biggest obstacle to the commercialization of SRM is the pulsating torque generated from the rotating shaft, which has various adverse effects not only on the device itself but also on the peripheral devices. Therefore, various methods for reducing the pulsating torque have been published by domestic and foreign researchers, and there is a study result that the hysteresis controller has an advantage in that it can flow a smooth current compared to the chopping control. However, in determining the hysteresis band, if the band is too small, it has a disadvantage in that it may cause a switching loss due to many switching and an unstable initial start when the encoder is used. Therefore, in this paper, a variable hysteresis controller that can reduce torque ripple in a steady state while having a more stable and fast speed response through the change of the hysteresis band according to the speed error.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.15 no.4
• /
• pp.291-297
• /
• 2022

This Paper is about the study that design performance and reliability measurement circuits of the IPM which is an intelligent switching switch module included at an inverter circuits for driving of A.C. Servo motors in home appliance. IPM is a core device of motor driver and it's switching characteristics should be retained uniformly during the driving of a servo system. All of it's specification, the collector emitter switch on voltage Vce(on) spec. is very important. As the IPM are core part of inverters and producing from several brands and versions, for optimal performances of application systems a method and measurement & evaluation system to measure Vce(on) value, collector emitter switch on voltage, of the IPM IGBT switches with various brands are required. Especially, the proposed method can measure and evaluate Vce(on) values of IPM with load at mounting state on the motor driving circuits and proposed measurement & evaluation system can be important instrument systems for IPM user companies.

• Korean Journal of Optics and Photonics
• /
• v.13 no.2
• /
• pp.146-150
• /
• 2002

1.55${\mu}{\textrm}{m}$ PnpN optical thyristor as a smart optical switch has potential applications in advanced optical communication systems. PnpP optical thyristors operating at 1.55${\mu}{\textrm}{m}$ are proposed and fabricated for the first time. In the optical thyristors, we employ InGaAs/InP multiple quantum well (MQW) for the active n- and p-layers. The thyristors show sufficiently nonlinear s-shape I-V characteristics and spontaneous emission. In the OFF-state, the device has a high-impedance up to switching voltage of 4.03(V). On the other hand, it has low-impedance and emits spontaneous light as a light-emitting diode in the ON-state voltage of 1.77(V), and switching voltage is changed under several light input conditions. It can be used as a header processor in optical asynchronous transfer mode (ATM), as a hard limiter in optical code division multiple access (CDMA) and as a wavelength converter in optical WDM systems.

• Korean Chemical Engineering Research
• /
• v.46 no.4
• /
• pp.732-738
• /
• 2008

Simulated moving bed (SMB) process is a continuous chromatographic technology used to separate a large amount of petrochemicals, fine chemicals, pharmaceuticals, and so on, drawing a great attraction of related industries. With the recent development of biotechnology, the SMB process has been adopted for the separation of various useful bio-products. Attempts to understand the separation mechanism of the SMB process in many aspects are reported in many publications. These researches have dealt with the improvement of SMB for easier operation and solving problem in process. The feed mixture fed into the SMB process may be of different concentration batch by batch rather than in uniform concentration. Retention behaviors of feed (psicose (A) and fructose (B) mixture) existing in the SMB unit in dynamic steady-state and feed (psicose (C) and fructose (D) mixture) newly injected into the SMB were analyzed. It was observed that the existing components, (A) and (B), were eluted relatively faster as the injection time of new feed was earlier during the port-switching period. In addition, the components (C) and (D) were eluted earlier as fresh feed was injected earlier in a port-switching time.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.6
• /
• pp.907-915
• /
• 2013

Tire Pressure Monitoring System (TPMS) is an auxiliary safety system for recognizing the condition of tires based on the pressure and temperature data transmitted from the sensor unit installed on a tire of the vehicle. Using TPMS, a driver can frequently check the state of tires and it aids to maintain the optimum running condition of the vehicle. Since TPMS must utilize the wireless communication technique to transmit data from a sensor unit to a signal processing unit installed in the vehicle, it suffers from interference signals caused by various external electrical or electronic devices. In order to suppress high-power interference signals, we employ beamforming techniques based on the uniform linear antenna array. As the number of the antennas is increased, the performance of the interference suppression is improved. However, there is the limit of the number of antennas, installed in the center of a vehicle, because of its size. In this paper, we compare and analyze the performance of the beamformer, when reducing the interelement spacing of antennas, to increase the number of the receiving antennas. For the performance analysis of the beamformers, we consider the switching beamformer and minimum-variance distortionless-response (MVDR) beamformer for TPMS, recently proposed.