• Textile Coloration and Finishing
• /
• v.26 no.1
• /
• pp.13-21
• /
• 2014

The object of this research is to perform the basic research for the development of selectively permeable membrane fabrics which is suitable for korean military in sense of embattlement. As a key factor of selectively permeable membrane fabrics which is suitable for korean military, this study selected the best PVA thickness and membrane selection for DMMP protection, pre-treatment method for conformational stability of face fabric and water/oil repellent process condition. Especially as the PVA coating thickness of the fabrics increase, peneration of DMMP decrease including water vapor permeation is lower. This study shows how physical features and permeability of chemical agents can be influenced by pre-treatment methods, the selection of selectively permeable membrane, the thickness of PVA etc. Results showed that outer shell / PVA / e-PTFE materials possessed performance with superior water vapor permeation (Over $3,000g/m^2/day$) and protective capability against DMMP vapor ($0.6{\mu}g/cm^2{\cdot}16hr$).

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.676-678
• /
• 2002

This paper deals with the design and characteristic analysis of a coreless an axial flux permanent magnet (AFPM) motor. Axial-flux permanent magnet motors prove to be the best candidate for application in electric vehicles (EVs) as direct-drive wheel motors, as in comparison with conventional motors they allow design with higher compactness, lightness and efficiency. Recently, issues regarding environment and the diversification of dependence in oil are watched with keen interest. In this theses, through the simulation of AFPM for low and high torque which has stator in the center and two rotors each side, understand its specialty, with this, make a prototype motor and design drive which can enhance the motors stability in low speed. Especially, specialty of motors torque power output will be mainly talked and based on this, possibility of application in EVs will be inspected by the theoretical study and the test.

• Tribology and Lubricants
• /
• v.28 no.1
• /
• pp.33-37
• /
• 2012

Automotive wheel bearing grease helps to reduce stresses and prevent wear of wheel bearings. But it is easily contaminated by water and other contaminants. Previously, our research group reported the change of grease physical properties such as dropping point, work penetration and oxidation work stability, water washout characteristics, leakage tendency, oil separation, evaporation loss and rust protection by water contamination. In this paper, we analyzed the physical characteristics of grease such as lubricity, viscosity and total acid number to investigate the mechanism of thickener decomposition. In water contaminated grease, the total acid number and wear scar were increased, the viscosity was decreased due to the decomposition of lithium complex thickener.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.12
• /
• pp.1699-1707
• /
• 2003

Coriolis mass flowmeter(CMF), which can measure the mass flow directly, is getting rapid attention for the industrial and custody transfer purpose. In order to study the characteristics and the applicability of CMF, it is tested with the national flow standard system. Two types of sensing tube, U-type and straight type, are employed in the test. Water, spindle oil and viscosity Standard Reference Material whose viscosities are 1, 20 and, 67 $\textrm{mm}^2$/s, respectively, are studied. It is shown that the linearity of CMF is getting deteriorated as the fluid viscosity increases, which is due to the zero drift and the relaxation time of the fluid. To test its applicability in the case of high pressured gas, it is calibrated using compressed air, It shows 1∼l.6 % deviations compared to the calibration results using water. It concludes that the fluid velocity in CMF should be lower than the sonic velocity. In addition, the effects of the vibration from the pipeline and pump on CMF as well as the long term stability are studied.

• Journal of KSNVE
• /
• v.5 no.4
• /
• pp.565-575
• /
• 1995

Gearboxes are often used in the petrochemical and electrical power plants to transmit mechanical power between two branches of a machinery train rotating at different speeds. When the gearboxes are connected with rotors supported by journal bearings, bearing loads vary in magnitude and direction with rotor speed and torque transmitted by the gearboxes. In this study, dynamic characteristics of the system which consists of gearboxes and a rotor supported by journal bearings are investigated analytically and experimentally by employing the polynomial transfer matrix method and modal analysis under different speeds and torque levels. Journal bearing loads due to the transmitted torque are claculated analytically and the stiffness and damping coefficient of the journal bearings are obtained using finite element method. Comparison of the analytical and experimental results shows that the cross coupled stiffness coefficients increase with increasing rotor speed, while the cross coupled damping coefficients decrease. This generates the oil whirl instability in the journal bearings. As the transmitted torque level goes up, the stiffness coefficients of the journal bearing and the first horizontal natural frequency increase. High levels of the transmitted torque produce high bearing stiffness since the contact loads of the mating gear teeth increase. The logarithmic decrement, which is a stability indicator, is shown to decrease with increasing speed and decreasing torque. Thus, at the low torque level, the system become unstable even at the low shaft speed.

• KSBB Journal
• /
• v.14 no.6
• /
• pp.737-741
• /
• 1999

Phenanthrene degrading bacteria were isolated from the petroleum contaminated soil near an oil tank. Four of 15 strains decreased surface tension of culture broth of phenanthrene-containing minimal media. H6, one of the isolated bacteria decreased surface tension of culture broth below 33 dyne/cm during growth on glucose. H6 was identified as Bacillus subtilis and biosurfactant produced by H6 was lipopeptide. The biosurfactant was produced at 0.13 g/L in the mineral medium containing 2% glucose. Critical micelle concentration(CMC) of the biosurfactant was 52 mg/L. Foaming power was similar to Tween 80 and dispersing power was superior to Tween 80m SDS and Brij30. High thermal stability and emulsion index were also observed.

• Elastomers and Composites
• /
• v.42 no.2
• /
• pp.112-118
• /
• 2007

An HRP immobilized carbon paste electrode, which was bound by EPDM, was newly fabricated and its electrochemical properties were investigated for the purpose of validating the new possibility for the practical use of biosensor. In the experimental range of substrate concentration, Lineweaver-Burk plot of the signal showed a good linearity. This means that HRP was embedded effectively to preserve its identity in the bulk of composite electrode materials and EPDM is a recommendatory binder. When the electrode was run at low operating potential($0.0\sim-1.0$ V vs. Ag/AgCl), it showed a high sensitivity and a good reproducibility. Especially the mechanical stability of the dried rubber was a remarkable breakthrough to get over a difficulty in putting the carbon-paste electrode bound with silicon oil to real use.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.234-235
• /
• 2007

Transparent nanosized $TiO_2$ sol has been made by sol-gel method, using Titanium(IV) isopropoxide precursor. To promote hydrolysis for titania is needed excess water, Oil bath and temperature about $80^{\circ}C$. $TiO_2$ sol is peptized ranging from pH 1 to 1.5 using hydrochloric acid for the stability of sol during a condensation reaction. The average particle size of $TiO_2$ sol was approximately 20nm. $TiO_2$-sillane sol was synthesized by surface treatment using MTMS to the $TiO_2$ sol. TEM analysis has been used to check the degree of dispersion and FT-IR analysis has been used to see if the sillane has been chemically bonded on the surface of $TiO_2$.

• The Journal of Asian Finance, Economics and Business
• /
• v.9 no.8
• /
• pp.7-17
• /
• 2022

The article discusses the problems caused by inflation in the developing Asia-Pacific region during the time of the worldwide pandemic and suggests innovative solutions to the problem. The reality is that some of the commodity groups from the consumer basket (e.g., non-seasonal fruits, electronics, furniture, hotel, and restaurant services, etc.) fail to reflect the needs of the low-income earners, which make the majority in developing countries. At the same time, the inflation targeting regime has become outdated and not reliable, because of uncontrolled exogenic factors (imported inflation, fluctuation in oil prices, supply chain disruption, Russia-Ukraine war, etc.) prevailing on endogenic factors and thus making it impossible to control the price stability, especially in developing countries. Since, the old-fashioned inflation index and inflation targeting mechanisms regrettably fail to fully reflect both the society and governmental/central banks' expectations, based on which we first should have better care and second create better policies; we propose to use a combination of already well-known indexes and policies, with the new statistical indicators, which reflects price fluctuations on the medication, utilities, and nutrition.

• Journal of the Korean Ceramic Society
• /
• v.41 no.3
• /
• pp.242-246
• /
• 2004

Nano-sized a-alumina with a narrow distribution was prepared by using Flame Spray Pyrolysis (FSP). The microemulsion of water in oil (W/O) was prepared to make ultrafine droplets for FSP process. Kerosene (fuel) as a continuos phase and Al(NO$_3$)$_3$$.$9$H_2O$ (oxidizer) aqueous solution as a dispersed phase were prepared for microemulsification. The microemulsion with dispersion stability was obtained by adjusting the composition of 80 vol% kerosene, 10 vol% aqueous solution, and 10 vol% emulsifying agent. Microemulsion was sprayed onto the flame by using two-fluid nozzle spray gun under the condition of 0.03 ㎫ air pressure. The synthesized products were $\alpha$-alumina phase with the size of 20 to 30 nm.