• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.739-742
• /
• 2000

From the experimental study of W-EDM for alloyed steel, the characteristics such as Hand Drum Form and surface roughness have been observed and evaluated for various conditions. In square hole, the increase of If as to made condition the calculate high value of surface roughness. Also compare dimensionless square hole with circle hole' graph. In circle hole, if a value of surface roughness IP 6 in a side of circle it show a 0.4${\mu}{\textrm}{m}$ and in IP 8, 0.6${\mu}{\textrm}{m}$, in IP 10, 0.7${\mu}{\textrm}{m}$, in IP 12. 0.8${\mu}{\textrm}{m}$ higher than before. This figure show the surface roughness is higher than before, because a table move in either X-axis or Y-axis in square hole, on the contrary, in circle there table move in X-axis and Y-axis at the same time. hand drum form getting small when wire tension increase 1000gf to 1500gf, at the same working conditions. the smaller of off time, the mailer of hand drum form in same condition and same wire tension. but if you compare square hole with circle hole' graph hand drum form displayed in maintained term of working condision, on the contrary, in case of square hole variation of hand drum form is more increase than a grow of IP

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.567-572
• /
• 2000

From the experimental study of W-EDM for alloyed steel, the characteristics such as Hand Drum Form and surface roughness have been observed and evaluated for various conditions. In square hole, the increase of IP as to made condition, the calculate high value of surface roughness. Also compare dimensionless square hole with circle hole' graph, In circle hole, if a value of surface roughness IP 6 in a side of circle it show a 0.4${\mu}{\textrm}{m}$ and in IP 8, 0.6${\mu}{\textrm}{m}$, in IP 10, 0.7${\mu}{\textrm}{m}$, in IP 12, 0.8${\mu}{\textrm}{m}$ higher than before. This figure show the surface roughness is higher than before, because a table move in either X-axis or Y-axis in square hole, on the contrary, in circle there table move in X-axis and Y-axis at the same time. hand drum form getting small when wire tension increase 1000gf to 1500gf, at the same working conditions. The smaller of off time, the maller of hand drum form in same condition and same wire tension. but if you compare square hole with circle hole' graph, hand drum form displayed in maintained term of working condision, on the contrary, in case of square hole variation of hand drum form is more increase than a grow of IP

• 소음진동
• /
• 제4권3호
• /
• pp.283-295
• /
• 1994

This work presents the experimental and finite element analysis results for the free vibration of 4 edges clamped, isotropic square plates with 2 collinear circular holes. Natural frequencies of finite element analysis are obtained for the complete square plate, the square plates with a central circular hole and the square plates with 2 collinear circulare holes. And natural frequencies are experimentally measured for the complete square plate, the square plate with a central circular hole(d = 150 mm) and the square plates with 2 collinear circular holes. Agreement between experimental and FEM results is excellent. Mode shapes in special case are presented. The conclusions of the study are as follows. There is little variation of nondimensional frequency parameters for the first six mode when the aspect ratio of circular hole is less than 1/6 in the isotropic square plates with 2 collinear circular holes. And the first nondimensional frequency parameter doesn't vary as the aspect ratio of circular hole increase.

• 대한기계학회논문집B
• /
• 제26권7호
• /
• pp.927-936
• /
• 2002

An experimental study has been conducted to investigate the heat/mass transfer characteristics within a film cooling hole of square cross-section for various blowing ratios and Reynolds numbers. The experiments have been performed using a naphthalene sublimation method and the flow field has been analyzed by numerical calculation using a commercial code. A duct flow enters into a film cooling hole in a cross-direction. For the film cooling hole with square cross-section, it is observed that the reattachment of separated flow and the vortices within the hole enhance considerably the heat/mass transfer around the hole entrance region. The heat/mass transfer on the leading edge side of hole exit region increases as the blowing ratios decrease because the main flow induces a secondary vortex. Heat/mass transfer patterns within the square film cooling hole are changed little with the various Reynolds numbers.

• 대한기계학회논문집B
• /
• 제28권4호
• /
• pp.456-466
• /
• 2004

An experimental study has been conducted to investigate the flow and heat/mass transfer characteristics within a rectangular film cooling hole of normal injection angle for various blowing ratios and Reynolds numbers. The results are compared with those for the square hole. The experiments have been performed using a naphthalene sublimation method and the flow field has been analyzed by numerical calculation using a commercial code (FLUENT). The heat/mass transfer around the hole entrance region is enhanced considerably due to the reattachment of separated flow and the vortices generated within the hole. At the hole exit region, the heat/mass transfer increases because the main flow induces a secondary vortex. It is observed that the overall heat/mass transfer characteristics are similar to those for the square hole. However, the different heat/mass transfer patterns come out due to increased aspect ratio. Unlike the square hole, the heat/mass transfer on the trailing edge side of hole entrance region has two peak regions due to split flow reattachment, and heat/mass transfer on the hole exit region is less sensitive to the blowing ratios than the square hole.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.967-972
• /
• 2008

This paper presents the free vibration analysis of a circular plate with a concentric square hole. The present problem deals with the numerical calculation of the natural frequencies and mode shapes of vibration of the structure by means of Independent Coordinate Coupling Method (ICCM). In this study, the boundary condition is the edge of the square hole is free and the outer circular plate is simply supported. Due to the geometric abnormality, this analysis does not permit an exact solution. Since the ICCM employs coordinate systems corresponding to each domain independently, the kinetic and potential energy expressions necessary for the Rayleigh-Ritz method can be easily obtained. Lastly, the kinematic relation is imposed. In this way, the eigenvalue problem can be easily set up. The numerical results show the efficacy of the ICCM and changes in natural frequencies and modes due to the square hole size.

• 한국소음진동공학회논문집
• /
• 제19권2호
• /
• pp.192-199
• /
• 2009

This paper presents the free vibration analysis of a circular plate with a concentric square hole. The boundary condition is the edge of the square hole is free and the outer circular plate is simply supported. Due to the geometric abnormality, this analysis does not permit an exact solution. The present problem deals with the numerical calculation of the natural frequencies and mode shapes of vibration of the structure by independent coordinate coupling method(ICCM). The numerical results show the efficacy of the ICCM and changes in natural frequencies and modes due to the square hole size.

• 한국소음진동공학회논문집
• /
• 제22권1호
• /
• pp.29-37
• /
• 2012

This paper is concerned with the natural vibration characteristics of a rectangular plate with a rectangular hole in contact with the water. The addressed problem was solved by using the Rayleigh-Ritz method combined with the Green function method. This study presents the numerical approach, numerical results and experimental results. In addition, the validity of the approximate formula which mainly depends on the so-called non-dimensionalized added virtual mass incremental factor and the natural mode shape change due to the presence of the water were investigated. Experiments were also carried out to validate theoretical results. The theoretical results are in good agreement with the experimental results. It was found that the effect of a square hole on the natural frequencies of the square plate in contact with water is different from the effect of a square hole on the natural frequencies of the square plate in air and the approximate formula can predict lower natural frequencies in water with a good accuracy.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.664-667
• /
• 1997

In this study, it is attempted to obtain the optimized size of holes in 15 square plate models where a hole exists on every quadrant of a plate, and to get eigenvalues and mode shapes by performing free vibration analysis for each model. For free vibration analysis and optimization of' hole sizes, the uniaxial tension is applied for the loading condition. From the results of this study, it is known that more stable structures can be designed by changing the natural frequency depending on the location and the optuiiunl size of holes. and further studies are considered to be necessary for the basic design information.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.14-21
• /
• 2001

An experimental study has been conducted to investigate the heat/mass transfer characteristics within a square film cooling hole with asymmetric inlet flow conditions. The asymmetric inlet flow condition is achieved by making distances between side walls of secondary flow duct and film cooling hole different; one side wall is $2D_h$ apart from the center of film cooling hole, while the other side wall is $1.5D_h$ apart from the center of film cooling hole. The heat/mass transfer experiments for this study have been performed using a naphthalene sublimation method and the flow field has been analyzed by numerical calculation using a commercial code. Swirl flow is generated at the inlet region and the heat/mass transfer pattern with the asymmetric inlet flow condition is changed significantly from that with the symmetric condition. At the exit region, the effect of mainstream on the inside hole flow is reduced with asymmetric condition. The average heat/mass transfer coefficient is higher than that with the symmetric condition due to the swirl flow generated by the asymmetric inlet condition.