• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.2
• /
• pp.294-301
• /
• 2000

One of the most important design parameters in a microwave radio transmitting system is to reduce spurious response from the output spectrum of the transmitting system. A Local oscillator (LO) is seldom totally pure and at the least contain some LO harmonic signals. A LO or any oscillator is a transmitter if provided with a suitable radiator, conduction, or leakage path. Where mixer is employed in the output of the LO mixer generated spurs can be increased by RF amplifier. To reduce LO leakage, notch filter or band pass filter has been conventionally used. In this paper, the leakage reduction(LR) signal, which has the same magnitude and the opposite phase with respect to LO leakage signal, is added to the output of mixer of the wireless LAN system. The LO leakage is reduced by 30 dB more than the conventional methods do. The proposed method is potentially suitable for low-cost, reliable, and simple application of monolithic microwave integrated circuits (MMICs)

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.3
• /
• pp.569-577
• /
• 1999

A wideband RF receiver for satellite mobile communications system was fabricated and evaluated of performance in low noise amplifier and high gain amplifier. The low noise amplifier used to the resistive decoupling and self-bias circuits. The low noise amplifier is fabricated with both the RF circuits and the self-bias circuits. Using a INA-03184, the high gain amplifier consists of matched amplifier type. The active bias circuitry can be used to provide temperature stability without requiring the large voltage drop or relatively high-dissipated power needed with a bias stabilized resistor. The bandpass filter was used to reduce a spurious level. As a result, the characteristics of the receiver implemented here show more than 55 dB in gain, 50.83 dBc in a spurious level and less than 1.8 : 1 in input and output voltage standing wave ratio(VSWR), especially the carrier to noise ratio is a 43.15 dB/Hz at a 1 KHz from 1537.5 MHz.

• Fire Science and Engineering
• /
• v.32 no.1
• /
• pp.57-65
• /
• 2018

In this study, a post-fire safe shutdown analysis (PFSSA) including multiple spurious operation (MSO) treatments for cables was conducted with an imaginary nuclear power plant for training using a deterministic fire analysis code. The imaginary nuclear power plant for the training consisted of a reactor containment building and an auxiliary building, including a total of 22 fire areas. The equipment including valves, pumps, emergency diesel generators, switch gears, motor control centers, and logic controllers were located in each fire area of the imaginary plant. It was assumed that each equipment is connected with two cables and that each cable passes through the fire areas along the cable trays. A database containing the information on the equipment and cables for the imaginary plant was constructed for the fire area analysis. The fire area analysis was performed for several assumed MSO scenarios, equipment logics, and cable logics. A mitigation measure using a three hour rated wrap was applied to the failed cables and cable trays after the fire area analysis.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.5
• /
• pp.67-74
• /
• 2013

A low-power 12-bit resistor string DAC for wireless sensor applications is presented. Two-step approach reduces complexity, minimizes power consumption and area, and increases speed. This chip is fabricated in 0.18-${\mu}m$ CMOS and the die area is $0.76mm{\times}0.56mm$. The measured power consumption is 1.8mW from the supply voltage of 1.8V. Measured SFDR(Spurious-Free Dynamic Range) is 70dB when the sampling frequency is less than 1 MHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.6
• /
• pp.600-613
• /
• 1997

The implementation of a BTS(Base station Transceiver) for WLL system using W-CDMA(Wideband-Code Division Multiple Access) method is presented in this paper. It consists of three boards; receiver, transmitter and RF controller. Some RF parameters are considered and simulated by the RF simulation S/W using commercial and customized components specifications. The implemented transceiver of 5 MHz RF channel bandwidth satisfies the system requirements of a transceiver such as dynamic range, sensitivity in the receiver and spurious emission suppression in the transmitter. At the receiver, the experimental measurement showed 2.86 dB of NF and 60 dB above of dynamic range in AGC(Automatic Gain Control) locking. At the transmitter, the -49.46 dBc of spurious emission suppression is attained when the output power of the transmitter is 34.3 dBm. These results are good enough to meet to standard performance specifications.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.2
• /
• pp.182-190
• /
• 2011

A amplitude modulation(AM) range measuring system utilizes the phase difference of the modulated envelope of the reflected signal to measure the distance. It is known that the AM system has a problem in accuracy due to antenna leakage signals and spurious reflection signals, but an AM range measurement system using an active reflector, which shifts the frequency bands, has been proposed in order to minimize the measurement errors due to spurious signals. In this paper, a new phase measurement module for the AM range measurement system, which enables to measure long distance with good accuracy, is proposed. The modulation frequency is alternatively selected between 8 and 1 MHz, and the measured distance range with this module is up to 150 m within 2 cm accuracy. A JK flip-flop circuit is used for higher phase accuracy, and an XOR circuit is used to cover long distance.

• Journal of Convergence for Information Technology
• /
• v.10 no.8
• /
• pp.47-52
• /
• 2020

In this study, a simulation investigation was conducted on the method of reducing switching noise and spurious emission among design methods for step-down DC-DC converter modules for automotive. A typical 4-layer converter circuit using a PMIC(Power Management Integrated Circuit) chip was presented, and the simulation results of conductive emissions at two input terminals (+, -) and the point between the input filter and the PMIC was performed in the 1.0~5.0MHz band and the 100MHz band. The results for the conducted and radiated emissions in the HF(3~30MHz) and VHF(30-300MHz) bands were presented. It showed an improvement of about 10dB over the bands by routing the output terminal placed on the 3 or 4-layer in the opposite direction to the input terminal. The result of this study is expected to be useful in the design of the DC-DC converter modules in the future because it gives a better improvement compared to the existing methods.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.8
• /
• pp.580-587
• /
• 2003

In this paper, we introduce a novel model to analyze the linearity of a TW-EAM (traveling-wave electroabsorption modulator). The device length, microwave loss (ML), and internal reflection (IR) due to impedance mismatch have effect on the linearity of a TW-EAM. The longer devices have characteristics of lower biases with minimum IMDS (intermodulation distortions). ML decreases the output power as well as the IMD value. Internal reflection has different nonlinear characteristics according to the wavelength of the input frequency and the device length. There is little change in SFDR (spurious-free dynamic range) due to ML or IR. As a result, for a 50 GHz band RF-optical communication system, a 0.8 mm-long TW-EAM with the lowest ML would have better properties by using n, which is caused by impedance, mismatch at the output port.

• Clinical and Experimental Reproductive Medicine
• /
• v.24 no.3
• /
• pp.369-375
• /
• 1997

Studies were conducted to determine the efficiency of decondensation protocols. Sperm obtained from seven normal donors was immediately washed after liquefaction and then decondensed using the method of West et al. (1989) and my original protocol. My optimized protocol entailed mixing 1 ml aliquots of semen with 4 ml phosphate buffered saline (PBS). Following centrifugation, pellets were resuspended in 1 ml PBS containing 6 mM EDTA. After centrifugation, pellets were resuspended in 1 ml PBS containing 2 mM dithiothreitol at $37^{\circ}C$ for 45 min. Following mixing with 2 ml PBS and centrifugation, pellets were resuspended by vortexing. While vortexing, 5 ml of fixative were gently added. Slide preparation was accomplished using the smear method and it was stored at $4^{\circ}C$. When comparing these protocols, the degree of sperm decondensation and head swelling was monitored by measuring nuclear length, area, perimeter, and degree of roundness using FISH analysis software. Apparent copy number for chromosome 1 and, separately, for the sex chromosomes was determined by FISH using satellite DNA probes for loci DIZ1, DXZ1 and DYZ3. Sperm treated by my decondensation protocol showed significant increases (p<0.05) in length, area, perimeter, and degree of roundness. There was a significant decrease (p<0.05) in the frequency of nuclei displaying no signal but no change in the frequency of nuclei with two signals in samples decondensed by my protocol. My data suggested that decondensation using my original protocol may lower the frequency of cells with spurious "nullisomy" due to hybridization failure without inducing spurious "disomy" resulting from increased distances between split signals.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.1
• /
• pp.8-16
• /
• 2020

In this paper, a single-bit 2nd-order delta-sigma modulator with the architecture of cascaded-of-integrator feedforward (CIFF) is proposed for column-parallel analog-to-digital converter (ADC) array used in a low noise CMOS image sensor. The proposed modulator implements two switched capacitor integrators and a single-bit comparator within only 10-㎛ column-pitch for column-parallel ADC array. Also, peripheral circuits for driving all column modulators include a non-overlapping clock generator and a bias circuit. The proposed delta-sigma modulator has been implemented in a 110-nm CMOS process. It achieves 88.1-dB signal-to-noise-and-distortion ratio (SNDR), 88.6-dB spurious-free dynamic range (SFDR), and 14.3-bit effective-number-of-bits (ENOB) with an oversampling ratio (OSR) of 418 for 12-kHz bandwidth. The area and power consumption of the delta-sigma modulator are 970×10 ㎛2 and 248 ㎼, respectively.