• Journal of Ecology and Environment
• /
• v.38 no.4
• /
• pp.443-450
• /
• 2015

The east coast of the Korean Peninsula is susceptible to fires because of the low rainfall in winter and spring, and large forest fires have occurred in this area. Lack of fresh water to combat fires has hampered efforts to prevent widespread forest fires in this region. Seawater has not been used as a suppressant because of possible detrimental effects of salt. We investigated the mobility of saline water in the forest soil and their effect on the microbial activity. Using a fire-fighting helicopter, seawater was sprayed over three plots (50 × 100 m) located on the eastern slope of the Baekdu mountain range in South Korea in April, 2011. We sampled the soil in April 4, May 20, and August 5 to determine the amount of salt that remained in the soil. The electrical conductivity value of the soil decreased to <400 μS/cm over a 1-month period. Approximately, four months after the application of seawater, the electrical conductivity value and Na⁺ content in all treatment plots did not significantly differ to those of the control plot, and total microbial activity also recovered to that of the control. Our results indicate that the amount of rainfall, soil physical-chemical properties, and topological factors may be a critical factor determining the mobility of saline water in forest soil.

• Corrosion Science and Technology
• /
• v.2 no.3
• /
• pp.155-160
• /
• 2003

Plasma spraying technique was used to fabricate functionally graded coating (FGC) of NiCrAIY/YSZ 8wt%$Y_2O_3-ZrO_2$ on a Co-base superalloy (HAYNES 188) substrate. Six layers were coated on the substrate for building up compositionally graded architecture. Conventional thermal barrier coating (TBC) of NiCrAIY/SZ with sharp interface was also fabricated. As-coated FGC and TBC samples were exposed at the temperature of $1100^{\circ}C$ for 10, 50, 100 hours in air. Microstructural change of thermally exposed samples was examined. Pores and microcracks were formed in YSZ layer due to evolution of thermal internal stress at high temperature. The amount of pores and microcracks in YSZ layer were increased with increasing exposure time at high temperature. High temperature oxidation of coatings occurred mainly at the NiCrAIY/YSZ interface. In comparison with the case of TBC. the increased area of the NiCrAIY/YSZ interface in FGC is likely to attribute to forming the higher amount of oxides.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.1
• /
• pp.94-100
• /
• 2019

This study was conducted on a high-temperature/high-pressure washer in which low-pressure cold water in a boiler is heated to a temperature range of $70{\sim}80^{\circ}C$ by supplying diesel combustion heat. The high-temperature water is sent to a compressor to increase its pressure to 200 bar, thereby making high-temperature/high-pressure water, which is sprayed through a spray nozzle. In the results of this study, the spray temperature of the high-pressure washing was shown to be the highest when the ratio between the actual amount of combustible air and the theoretical amount of air was 1:1 and the energy consumption rate of the low-pressure boiler type high-pressure washer was shown to be much lower than that of the high-pressure boiler type high-pressure washer.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.5
• /
• pp.486-493
• /
• 2001

Partially stabilized zirconia (PSZ) is an attractive material for thermal barrier coating. Zirconia exists in three crystallographic phases: cubic, tetragonal and monoclinic. Especially, the phase transformation of tetragonal phase to monoclinic phase accompanies significant volume expansion, so this transition generally results in cracking and contributes to the failure of the TBC system. Both the plasma sprayed ZrO$_2$-8Y$_2$O$_3$ (YSZ) coat and the ZrO$_2$,-25CeO$_2$,-2.5Y$_2$O$_3$ (CYSZ) coat are isothermally heat -treated at 130$0^{\circ}C$ and 150$0^{\circ}C$ for 100hr and cooled at different cooling rates. The monoclinic phase is not discovered in all the CYSZ annealed at 130$0^{\circ}C$ and 150$0^{\circ}C$. In the 150$0^{\circ}C$ heat-treated specimens, the YSZ contains some monoclinic phase while none exists in the 130$0^{\circ}C$ heat-treated YSZ coat. For the YSZ, the different phase transformation behaviors at the two temperatures are due to the stabilizer concentration of high temperature phases and grain growth. For the YSZ with 150$0^{\circ}C$-100hr annealing, the amount of monoclinic phase increased with the slower cooling rate. The extra oxygen vacancy, thermal stress, and c to t'phase transformation might suppress the t to m martensitic phase transformation.

• Journal of Fashion Business
• /
• v.20 no.6
• /
• pp.94-110
• /
• 2016

A necessity for infants, diapers are not only used over long durations, but are also in direct contact to the infants' skin, making the choice of diaper to be of utmost importance. Current interest in cloth diapers is rapidly increasing because of issues concerning the baby's health, green environment, and economy. However, previous researches on cloth diapers are limited to simply investigating the form and material of commercial cloth diapers. There are few in-depth researches for the optimal cloth diaper development. This is therefore a fundamental research for the development of optimized cloth diapers, and analyzes the difference in absorption depending on the placement of seam line (liner, darts, and I pattern), the locations of liquid spraying (1 cm and 8 cm ahead of the center), and the amount of liquid capacity (10 and 20 ml). Currently, the development of diaper patterns considers the crotch shape of the infants and the skin length deformation. As a result, in the case of the I-pattern, the horizontal seam line prevents water from spreading to the front and back, thus reducing the absorbed area. This result was more clearly visible when water was sprayed at the center. The effect of the seam line became more obvious when there was more water (20 ml); also, when water was sprayed at the center, more leakage was observed. Using the results of this research, implementation of horizontal seam is expected to prevent the upward spread of urine.

• Journal of Welding and Joining
• /
• v.14 no.6
• /
• pp.109-118
• /
• 1996

Al$_2$O$_3$-TiO$_2$powders of six different compositions were plasma-sprayed on Ti substrate. The spray powders and the spray coated layers were analysed and compared using SEM and X-RD. The elastic properties (specific elastic constant and damping coefficient) of the coated specimens were measured in order to select the optimum composition range of ceramics for use in a speaker diaphragm. A correlation between the microstructure and elastic properties was also investigated. When $Al_2$O$_3$powders with 0- 13% TiO$_2$were plasma sprayed, the coated layers were composed of metastable y-Al$_2$O$_3$with small amount of $\alpha$-Al$_2$O$_3$and the content of $\alpha$-Al$_2$O$_3$was increased with TiO$_2$content. Specific elastic constant was rapidly increased with 2 and 13% TiO$_2$addition to $Al_2$O$_3$. The internal damping was nearly unchanged with TiO$_2$content The specific elastic constant seemed to be dependent on the content of $\alpha$-Al$_2$O$_3$in the coated layer.

• Nuclear Engineering and Technology
• /
• v.45 no.5
• /
• pp.683-688
• /
• 2013

Candidate coating materials for re-usable metallic nuclear fuel crucibles, TaC, TiC, ZrC, $ZrO_2$, and $Y_2O_3$, were plasmasprayed onto a niobium substrate. The microstructure of the plasma-sprayed coatings and thermal cycling behavior were characterized, and U-Zr melt interaction studies were carried out. The TaC and $Y_2O_3$ coating layers had a uniform thickness, and high density with only a few small closed pores showing good consolidation, while the ZrC, TiC, and $ZrO_2$ coatings were not well consolidated with a considerable amount of porosity. Thermal cycling tests showed that the adhesion of the TiC, ZrC, and $ZrO_2$ coating layers with niobium was relatively weak compared to the TaC and $Y_2O_3$ coatings. The TaC and $Y_2O_3$ coatings had better cycling characteristics with no interconnected cracks. In the interaction studies, ZrC and $ZrO_2$ coated rods showed significant degradations after exposure to U-10 wt.% Zr melt at $1600^{\circ}C$ for 15 min., but TaC, TiC, and $Y_2O_3$ coatings showed good compatibility with U-Zr melt.

• Korean Journal of Agricultural Science
• /
• v.39 no.4
• /
• pp.569-575
• /
• 2012

This study was performed to investigate the effect of a sequencial washing of organic acid and distilled water on meat quality and the population of Escherichia coli of pork loin during cold storage. E. coli ATCC25922 was inoculated on the surface of sliced pork loin and 50 mL of 1% or 2% of organic acid and the same amount of distilled water was sprayed on the surface of pork loin. Then, physicochemical and microbial properties of pork loin were analyzed during cold storage. During storage period, lightness, yellowness and lipid oxidation (thiobarbituric acid reactive substances value) was higher than those of not treated control. However, the population of E. coli was decreased significantly in formic acid and distilled water sprayed pork loin samples. From these results, it can be considered that application of combination of washing of formic acid and water in the washing step of pig slaughter may be helpful to control the proliferation of E. coli.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.17 no.3
• /
• pp.203-211
• /
• 2007

This study was conducted in cut rose cultivation field in Goyang to evaluate pesticide exposure of farmers and the relationship between the exposure and work environment/method for cut rose farmers. Dermal exposure was assessed with patch (thin chromatography layer paper), cotton glove by body parts during mixing and spraying works in which pyrethroid, organophosphate, carbamate pesticide were used in 4 cut rose greenhouses located in Goyang province, checking characteristics of environment/working method at the same time. Body parts assessed were as follows ; glove : hand, patch : head, neck(front/back), chest, back, shoulder(right/left), upperarm(right/left), forearm(right/left), thigh(right/left), shin(right/left). Pesticides were analyzed using gas chromatography(NPD/FID) after extracting with ethyl acetate. Exposure amount differed according to pesticide type. But after standardizing with total net weight of pesticide sprayed, there were no significant difference among pesticides. There were significant difference in exposure amount among body parts(especially exposure amount of thigh, shin were more than the others), which means exposure happen not by pesticide dispersion in air but by contact with cut rose(leaf, branch) indirectly. Walking forward during spraying made farmers more exposed than waling backward, these results means contacts with leaves/branches made exposure happen in cut rose greenhouse also. As a result, pesticide exposure in cut rose greenhouse was related with contact of leaf/branch which pesticide remained in, which made exposure pattern (especially exposure amount) differ by body parts

• Korean Journal of Environmental Agriculture
• /
• v.29 no.1
• /
• pp.66-71
• /
• 2010

Jinpi(Aurantii nobilis Pericarpium) is one of the most important material of oriental herbal medicine which is made from the peel of mandarin by washing with hot water and drying. Pesticides have necessarily used for mandarin cultivation according to their preharvest intervals (PHIs) but their maximum residue limits (MRLs) and PHIs for Jinpi are not established yet. This study is to know residue amount of organophosphorus insecticides in Jinpi and to establish the MRLs and PHIs for fenitrothion and phenthoate in Jinpi. Fenitrothion was sprayed once, twice and three times with 7 days interval before harvest. Its residue amount ranged from 0.14 to 1.17 mg/kg in mandarin, 0.59 to 4.02 mg/kg in its peel and 1.66 to 22.38 mg/kg in Jinpi. In case of phenthoate, it was sprayed with 10 days interval for 10 days before harvest. Its residue amounts in mandarin, its peel, and Jinpi ranged from 0.16 to 0.65, 0.69 to 2.41 and 1.69 to 11.3 mg/kg, repectively. Proposed MRLs of fenitrothion and phenthoate for Jinpi are suggested to 22.39 and 11.30 mg/kg, respectively. So we recommend PHIs of the pesticides that fenitrothion can be sprayed 3 times 7 days before harvest and in case of phenthoate, sprayed 3 times 10 days before harvest.