• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.7 no.4
• /
• pp.50-55
• /
• 2008

CNC wire bending machines are used in industries to make a type variety of wire products such as long links. The machines have a long arm device to rotate in order to remove forming errors by flexibility of wire. Generally, the machines which constructed servo motors in the arm have the rotating range of the arm under 360 degree because the servo motors connect with fixed control devices on frame by many cables. The rotating angle under 360 degree limits working speed and forming geometry. Therefore this study developed a gear train to drive a parts in arm and to be independent on arm rotation movement. The developed gear train can transfer four movements to four components in arm and is consists parallel of four pairs of satellite gear trains. This study constructed the CNC wire bending machine with the developed gear train and verified that the gear train could drive internal components independently on arm rotation.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1530-1535
• /
• 2003

The automatic load transfer switch (ALTS) typically automatically transfers electrical loads from a normal electrical power source to an emergency electrical power source upon reduction or loss of normal power source voltage. It can also automatically re-transfer the load to the normal power source when the normal voltage has been restored within acceptable limits. The transfer operation of ALTS is accomplished by a spring-driven linkage mechanism. In this paper we build a dynamic model of driving mechanism for ALTS using ADAMS and checked the characteristics of the transfer operation. Finally we performed a detailed design of the driving mechanism through results of analysis and confirmed it to satisfy design requirements.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.816-821
• /
• 2013

This case study presents a practical method to reduce resonant vibration of generator-motor set. The generator is driven at 1800rpm by induction integral motor. The vibration is below alarm limits, but the dominant frequency of vibration is sub-synchronous and close to that of bearing fault signal in spite of new bearings. To find an mechanism of abnormal vibration, ODS and Modal analysis is carried out. The measured modal characteristics were compared with those of FE Analysis. The ODS mode at rated speed is consistent with system natural frequency mode that is excited by bearings. To reduce vibration level, the isolation mount at system base is changed with new rubber mount for lower natural frequency.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.14 no.10
• /
• pp.4098-4116
• /
• 2020

Mobile devices such as smartphones are very attractive targets for augmented reality (AR) services, but their limited resources make it difficult to increase the number of objects to be recognized. When the recognition process is scaled to a large number of objects, it typically requires significant computation time and memory. Therefore, most large-scale mobile AR systems rely on a server to outsource recognition process to a high-performance PC, but this limits the scenarios available in the AR services. As a part of realizing large-scale standalone mobile AR, this paper presents a solution to the problem of accuracy, memory, and speed for large-scale object recognition. To this end, we design our own basic feature and realize spatial locality, selective feature extraction, rough pose estimation, and selective feature matching. Experiments are performed to verify the appropriateness of the proposed method for realizing large-scale standalone mobile AR in terms of efficiency and accuracy.

• Journal of the Korea Society of Computer and Information
• /
• v.5 no.2
• /
• pp.81-89
• /
• 2000

In this thesis. we. present a Telemedicine System that uses the communication network as the 2s6kbps exclusive line or 10Mbps Ethernet LAN. This system can make it possible for remote hospital or doctor to search and retrieve medical images and information from the central hospitals the have advanced technologies, and to support Teleconsulting with medical experts. To solve the speed limits. JPEG compression method and Distributed system used.

• KIEE International Transactions on Power Engineering
• /
• v.5A no.2
• /
• pp.152-158
• /
• 2005

This paper describes a reactive optimal power flow incorporating margin enhancement constraints. Margin sensitivity at a steady-state voltage instability point is calculated using invariant space parametric sensitivity, and it can provide valuable information for selection of effective control parameters. However, the weakest buses in neighboring regions have high margin sensitivities within a certain range. Hence, the control determination using only the sensitivity information might cause violation of operational limits of the base operating point, at which the control is applied to enhance voltage stability margin in the direction of parameter increase. This paper applies an interior point method (IPM) to solve the optimal power flow formulation with the margin enhancement constraints, and shunt capacitances are mainly considered as control variables. In addition, nonlinearity of margin enhancement with respect to control of shunt capacitance is considered for speed-up control determination in the numerical example using the IEEE 118-bus test system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.37-45
• /
• 2003

The diesel engines was invented a little more than one hundred years ago and has ever since been developed for better fuel economy, increased power and smaller size. Thanks to its fuel economy, the diesel engine is today the dominating prime mover in many applications, such as smaller power plants, commercial ships, trains, trucks, buses and all kinds of mobile construction machinery. As engine for passenger cars, the diesel engine is steadily increasing its share of the market. However, its versatility and, consequently, large prevalence have led to environmental demands to its exhaust emissions, noise and vibration. This paper deals with the noise aspects of diesel engine designs of the so-called low speed two-stroke type installed in most large ships.

• Journal of the Korea Safety Management & Science
• /
• v.12 no.4
• /
• pp.175-181
• /
• 2010

The government have plans to improve the railway transport capacity and transport hub for the sustainable national transport and logistics system. Specially, there are much efforts to improve transportation capacity such as high speed transportation of rail freight, enlargement of BT train, development of double stack train, etc. between railway transport hubs. If the transport capacity between railway logistics hubs is increased as planned, we must increase the handling capacity of railway hub terminals. But there are limits to enlarge the terminal infrastructure because of investment scale, location circumstances and urban development plans. To ensure the capacity, with the minimum required enlargement of infrastructure, it is necessary to extremely increase the efficiency of terminal operations. For improving the efficiency, we have to introduce the efficient terminal operation systems based on u-IT and operation optimize technologies. In this paper, we analyse the issues and problems of railway terminals(including ICD) and suggest the concept of intelligent railway terminal and the construction components of technology.

• Proceedings of the IEEK Conference
• /
• 2002.07c
• /
• pp.2059-2062
• /
• 2002

For detection of digitally modulated signals, the receiver must be provide with accurate carrier phase and symbol timing estimates. So far, tots of algorithms have been suggested for those purposes. In general, a interpolation filter with TED(Timing Error Detection) like Gardner algorithm is popularly used for symbol timing estimate of digital communication receiver. Apart from the performance point of view, a multiplicative operation of any interpolation filter limits the symbol rate of the system. Hence, we suggest a new symbol timing estimate algorithm for high speed burst-mode fixed wireless communication system and analyze its performance in the AWGN channel.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.7
• /
• pp.494-499
• /
• 2000

In a conventional stator flux-oriented(SFO) induction machine drive system, the field weakening method is to vary flux reference in proportion to the inverse of the rotor speed. This paper investigates that maximum torque capability cannot be obtained in the conventional system and proposes a new selection method of flux reference to obtain maximum torque capability over the field weakening region by considering voltage, torque, and current limits.