• Journal of the Korean Geotechnical Society
• /
• v.23 no.5
• /
• pp.111-129
• /
• 2007

The standard construction manual of the SDA(Separated Doughnut Auger) piling method was proposed so that the resisting capacity of the augered piles could work effectively. 405 dynamic pile load tests and 30 static pile load tests were performed for 265 test piles, which were installed by the SDA piling method in 33 sites in Korea. The results of the pile load tests showed that the end bearing capacity of the SDA augered piles depended on the property of various soil stratums and did not agree with ones estimated by the existing formula based on several standard design codes. On the basis of the pile load test results, four formulas were presented according to bearing stratums to estimate quantitatively the unit end bearing capacity of the SDA augered piles. The formulas for the unit end bearing capacity of piles on soils or weathered rocks were related to N-value given by SPT(Standard Penetration Test), while the unit end bearing capacity on bedrock was suggested to be more than 1500 $tf/m^2$. The presented formulas were compared with the existing formulas, which were presented by several standard design codes to design the augered piles. In order to use correctly the presented formulas, the quality of Standard Penetration Test should be controlled precisely. Also it is desirable to choose a pilot construction site, where both dynamic and static pile load tests are performed.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.2C
• /
• pp.85-93
• /
• 2010

The shear stiffness has become an important design parameter to understand the soil behavior. In particular, the elastic moduli and void ratio has been considered as important parameters for the design of the geotechnical structures. The objective of this paper is the development of the penetration type Field Velocity and Resistivity Probe (FVRP) which is able to assess the elastic moduli and void ratio based on the elastic wave velocities and electrical resistivity. The elastic waves including the compressional and shear wave are measured by piezo disk elements and bender elements. And the electrical resistivity is measured by the resistivity probe, which is manufactured and installed at the tip of the FVRP. The penetration tests are carried out in calibration chamber and field. In the laboratory calibration chamber test, after the sand-clay slurry mixtures are prepared and consolidated. The FVRP is progressively penetrated and the data are measured at each 1 cm. The field experiment is also carried out in the southern part of Korea Peninsular. Data gathering is performed in the depth of 6~20 m at each 10 cm. The elastic moduli and void ratio are estimated based on the analytical and empirical solutions by using the elastic wave velocities and electrical resistivity measured in the chamber and field. The void ratios based on the elastic wave velocities and the electrical resistivity are similar to the volume based void ratio. This study suggests that the FVRP, which evaluates the elastic wave velocities and the electrical resistivity, may be a useful instrument for assessing the elastic moduli and void ratio in soft soils.

• Journal of Korean Society of Forest Science
• /
• v.84 no.4
• /
• pp.479-488
• /
• 1995

Relationships between pine-mushroom(Tricholoma matsutake) yield and important climatic factors for the yield(such as monthly precipitation, relative humidity, temperature, and radiation percentage) were examined to find out limiting factors for pine-mushroom production and to develop a method for overcoming the factors by analyzing the yield and climate data for 17 years collected from 18 main regions of pine-mushroom production. Although there were variations among the production regions, climatic condition of September was the most significant factor for pine-mushroom yield in general, and the degrees of importance of each climatic factors were different among the production regions. Mean minimum temperature of September was positively correlated with pine-mushroom yield($$r^2{\geq_-}0.41$$) at the 1% level, of which were 9 regions such as Youngduck, Uljin, Samchuck, Bongwha arid so on. In these regions, vegetation control was expected to be effective for pine-mushroom production by allowing much sunlight penetration to the pine stand, which may increase soil temperature and keeping the temperature around the fungal colony in soil. Precipitation during September was positively correlated with pine-mushroom yield($$r^2{\geq_-}0.41$$) at Namwon, Moonkyung and Sangju. Thus, irrigation around fungal colony in dry soil during September would be effective for enhancing mushroom yield at the regions. Pine-mushroom yield of 1994 was quite low, similar to that of 1993, due to serious drought. In this period, we could manifest the possibility of enhancing pine-mushroom yield by irrigation for overcoming drought at Moonkyung and Keochang regions.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.1
• /
• pp.179-189
• /
• 2000

The purpose of this research is to complement the existing researches on landfill bottom liners behavior during the periods of freeze and thaw. Landfill-related researches have been typically focused on small-scale soil samples that are often compacted under conditions different from those used in the field. Although these tests have been invaluable in clarifying the problem of freeze and thaw, extending the results of such experimental studies to prototype landfills are questionable. In this investigation, the author utilized a large scale laboratory simulation allowing inclusion of the field depth of the cover systems, layered soil profiles, rainfall simulation, a cold climate and boundary conditions similar to those encountered in the landfill. The soil materials were stabilized soils (mixed clays, cements, and minerals) instead of clays. The bottom liners are made up of drainage layer (30 cm), stabilized layer (75 cm), and leach collection layer (60 cm). The stabilized layers are made up of supporting layer (45 cm) and low permeable layer (30 cm) - consisting of $P_A\; and\; P_B$ layer. As a results, depths of penetration increased by about 2~5 more centimeters at rainfall simulated designs than those at no rainfall simulated designs (that is design 3, design 5 and design 7) - it increased by about 20mm/day in the bottom liners and frost heaves also increased it by a few millimeters. Also, a few cracks appeared partly. According to these results, we can surmise that the compacted stabilized soil is more reliable than the compacted clay liners for construction of the landfill liners.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.12 no.2
• /
• pp.77-84
• /
• 1992

This experiment was designed to gain information on factors affecting stubble death of orchardgrass (Dactylis glomerata L.) during the first rainy season. According to the experimental plan, the effects of sowing methods, drainages and cutting dates on the stubble carbohydrate content of orchardgrass, available soil moisture content of experimental plots, temperatures at the ground level and in the soil, and relative light intensity and humidity at the base of orchardgrass canopy were measured during the rainy season. The carbohydrate content of orchardgrass was sharply decreased to 2.9 % at 3rd day after cutting in the plots cut before rainy season and a gradural recovery was noted following the sharp reduction, but in the plots cut after rainy season, orchardgrass showed 5.5% of carbohydrate content before cutting and 3.0% at the 3rd day after cutting. The same pattern in both carbohydrate reduction and recovery was found between two cutting treatments. The available soil moisture content in the plots cut before rainy season was slightly higher than that in the plots cut after rainy season. But after the rainy season, the available soil moisture content in the plots cut after rainy season was higher than that in the plots cut before rainy season. Soil temperature at lOcm depths in the plots cut before rainy season was higher than that in the plots cut after rainy season. Daily maximum air temperature at the ground level in the plots cut before rainy season was higher than that in the plots cut after rainy season and changeable. Relative humidity at the ground level was below 70% in the plots cut before rainy season, but 75 to 90 % was observed in the plots cut after rainy season. Relative light intensity at the ground level in the plots cut before rainy season was much higher, recorded 50 to 90 %, than that in the plots cut after rainy season showing less than 10%. The results of this study suggest that the stubble death of orchardgrass during the rainy season is due to plant diseases influenced by a decrease of light penetration and increase of relative humidity at the base of the grass canopy.

• Journal of the Korean Geosynthetics Society
• /
• v.7 no.4
• /
• pp.37-45
• /
• 2008

A pilot test using environmentally friendly drains, was carried out to evaluate their applicability potential in the field. The pilot test site was divided into 5 different areas, with several combinations of vertical and horizontal drains installed for evaluation. Conventional natural fiber drains (FDB), new developed straw drain board (SDB) and plastic drain board (PDB) were used as vertical drains, while sand and fiber mats were used as horizontal drains. Surface settlement rates and excess pore pressure generation/dissipation tendency of PDB and FDB are almost identical except those of SDB. Cone tip resistance obtained from cone penetration test measured at the end of 1st consolidation stage for upper soft layer definitely increased irrespective of types of vertical drains. The monitoring and site investigation test data obtained at the pilot test site prove the vertical natural fiber drains can be used as substitutes of conventional plastic and sand material.

• Journal of the Korean GEO-environmental Society
• /
• v.17 no.4
• /
• pp.5-15
• /
• 2016

For achieving stability and economic construction at a retaining wall construction site, quantitative parameters of soil properties with excavation steps coincides with the actual field site. The main parameters of retaining wall design such as deformation modulus and modulus of horizontal subgrade reaction are common with N value of standard penetration test. Therefore, this study is compared and analyzed about the mutual relationship which is SPT, PBT and PMT for overcoming inconsistency of the existing retaining wall design generalized. In addition, modulus of horizontal subgrade reaction and reduction factor with excavation steps are proposed through back analysis of elasto-plasticity and finite element method with actual field monitoring data. Finally, it is purpose that parameter errors are reduced for applying effective retaining wall design at a construction small and medium-sized.

• Corrosion Science and Technology
• /
• v.18 no.6
• /
• pp.277-284
• /
• 2019

External corrosion control of buried pipe can be achieved by the combination of barrier coating and cathodic protection. Coating damage and deterioration can be induced by many reasons; damage during handling and laying, enhanced failure at low temperatures, failure during commissioning and operation, disbanding due to inadequate surface cleaning, rock penetration during installation and service etc. This work focused on the effect of survey conditions on the reliability of coating flaw detection of buried pipes. The effects of applied voltage and anode location on the detection reliability of coating flaw of buried pipe in soil with the resistivity of ca. 25.8 kΩ·cm were discussed. Higher applied voltage increased the detection reliability, regardless of buried depth, but deeper burial depth reduced the reliability. The location of the anode has influenced on the detection reliability. This behaviour may be induced by the variation of current distribution by the applied voltage and buried depth. From the relationship between the applied voltage and reliability, the needed detection potential to get a desire detection reliability can be calculated to get 100% detection reliability using the derived equation.

• Journal of the Korean Geosynthetics Society
• /
• v.13 no.1
• /
• pp.53-61
• /
• 2014

Sea gives us a lot of benefits and one of them is a role of transporting goods easily by ship. Accordingly the industrial area or the container yard is constructed either on the low sea or near the sea. Sea dredging ground is made by pumping them using dredge pump to the inside of embankment after dredging undersea soils. The dredging ground after pumping is in the slurry state but as time goes, consolidation by the own weight happens and evaporation happens at the surface of dredging ground. The evaporation causes the crest layer in the upper side of dredging ground. Under the crest layer there is still a soil of slurry state which has just little bearing resistance. This kind of characteristics makes it difficult to get a exact bearing capacity using the equations proposed until now. In this study we have performed simultaneously both the field loading tests and the cone penetration tests on the sea dredging ground. From the result of field tests, new experimental equation for the ultimate bearing capacity has been proposed. If we use the new equation, it is believed that some design of sea dredging ground could be more accurate.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.38 no.3
• /
• pp.429-438
• /
• 2018

Cone and T-bar penetrometers have been frequently used to estimate the undrained shear strength of clay. For small-size model tests, miniature penetrometers should be used but their correlation factors have not been well published. In this study, a testing setup was developed to derive empirical factors of the miniature cone and T-bar penetrometers. A 350mm-diameter chamber and kaolin clay were utilized to prepare soil specimens consolidated under four different pre-consolidation pressures controlling undrained shear strength. Two miniature cones with two diameters of 10-mm and 16-mm and a T-bar penetrometer with 10-mm diameter were used to investigate boundary effect, penetration rate effect, and diameter and shape effect. Unconsolidated-undrained triaxial tests were carried out with samples taken from the specimens to measure undrained shear strength. Finally, empirical factors for the penetrometers were constructed to correlate tip resistance to undrained shear strength.