• Journal of Power Electronics
• /
• 제16권1호
• /
• pp.93-101
• /
• 2016

A new four-primary-switch diode clamped soft switching three-level DC-DC converter (TLDC) with full zero-voltage switching (ZVS) load range and TL secondary voltage waveform is proposed. The operation principle and characteristics of the presented converter are discussed, and experimental results are consistent with theoretical predictions. The improvements of the proposed converter include a simple and compact primary structure, TL secondary rectified voltage waveform, wide load range ZVS for all primary switches, and full output-regulated range with soft switching operation. The proposed converter also has some disadvantages. The VA rating of the transformer is slightly larger than that of conventional TLDCs in variable input and constant output mode. The conduction loss of the primary coil is slightly higher because an air gap is inserted into the magnetic cores of the transformer. Finally, the secondary circuit is slightly complex.

• Journal of Electrical Engineering and Technology
• /
• 제6권3호
• /
• pp.350-355
• /
• 2011

This paper deals with the comparison of magnetic characteristics in transverse flux rotary machine according to different stator core composition with the same rotor. Three different stator designs are considered in the analysis according to the material composition of inner and outer stator cores. Electromotive force (EMF), inductance, torque, and core losses are calculated by threedimensional finite element analysis. Calculated and measured results of back-EMF according to the analysis models in dependency on speed are presented.

• 한국분말재료학회지
• /
• 제13권4호
• /
• pp.256-262
• /
• 2006

The amorphous $Fe_{73}Si_{16}B_7Nb_3Cu_1$ alloy strip was pulverized to get a flake-shaped powder after annealing at $425^{\circ}C$ for 90 min and subsequently ground to obtain finer flake-shaped powder by using a ball mill. The powder was mixed with polyimide-based binder of $0.5{\sim}3wt%$, and then the mixture was cold compacted to make a toroidal powder core. After crystallization treatment for 1 hour at $380{\sim}600^{\circ}C$, the powder was transformed from amorphous to nanocrystalline with the grain size of $10{\sim}15nm$. Soft magnetic characteristics of the powder core was optimized at $550{\sim}600^{\circ}C$ with the insulating binder of 3wt%. As a result, the powder core showed the outstanding magnetic properties in terms of core loss and permeability, which were originated from the optimization of the grain size and distribution of the insulating binder.

• Journal of Magnetics
• /
• 제10권3호
• /
• pp.122-127
• /
• 2005

New classes of LC resonators for micro magnetic sensor device were proposed and fabricated. The first type LC resonator (Type I) consists of a small piece of microwire and two cylindrical electrodes at the end of the microwire without direct contact to its ferromagnetic core. In type I resonator the ferromagnetic core of the microwire and cylindrical electrodes act as an inductor and two capacitors respectively to form a LC circuit. The second type LC resonator (Type II) consists of a solenoidal micro-inductor with a bundle of soft magnetic microwires as a core. The solenoidal micro-inductors fabricated by MEMS technique were $500\sim1,000\;\mu{m}$ in length with $10\sim20$ turns. A capacitor is connected in parallel to the micro-inductor to form a LC circuit. A tiny glass coated $CO_{83.2}B_{3.3}Si_{5.9}Mn_{7.6}$ microwire was fabricated by a glass-coated melt spinning technique. A supergiant magneto-impedance effect was found in a type I resonator as much as 400,000% by precise tuning frequency at around 518.51 MHz. In type II resonator the changes of inductance as a function of external magnetic field in micro-inductors with properly annealed microwire cores were varied as much as 370%. The phase angle between current and voltage was also strongly dependent on the magnetic field. The drastic increments of magnetoimpedance at near the resonance frequency were observed in both types of LC resonators. Accordingly, the sudden change of the phase angle, as large as $180^{\circ}C$, evidenced the occurrence of the resonance at a given external magnetic field.

• 한국표면공학회지
• /
• 제15권1호
• /
• pp.11-18
• /
• 1982

80% Ni-Permalloy is soft magnetic material with high initial permeability and low magnetic coercive force Hc, and is used to computer memory cores and minirelays of communication e-ngineering. In this paper 80 Permalloy thin film on copper cathode was alloy-deposited from Watts so-lution contatining FeSO4$.$7H2O. The amount of FeSO4$.$7H2O in the solution, pH, temperature of the solution and plating current density were varied as parameters and the resulting comp-osition changes of deposited film were analyzed electrochemically with respect to the parame-ters. From the above procedure electroplating conditions for deposition of 80 Permalloy were est-ablished as following: 17-21 g/$\ell$ of FeSO4$.$7H2O in Watts solution, current density 1.0-2.0 Amp/dm2, pH 2.5-3.0 and temperature range of 50-60$^{\circ}C$.

• 전기전자학회논문지
• /
• 제23권2호
• /
• pp.599-605
• /
• 2019

페라이트 코어는 연자성 재료로서 유도형 전력선 통신을 위한 결합기 제작에 사용되고 있다. 그러나 전력선 통신환경에 따라 크기를 자유롭게 조절하기 어려운 재료이다. 본 논문에서는 페라이트 보다 투자율이 높은 나노 결정립합금을 이용하여 광대역 전력선 통신용 유도형 결합기 재료로 적용할 수 있음을 보고한다. 나노결정립은 얇은 리본 형태로 제조되므로 토로이달 코어에 감긴 리본의 횟수로 결합기의 크기를 자유롭게 조절할 수 있다. 함침법으로 만든 코어를 이용하여 유도형 결합기를 제작하였고, 이를 비접촉식 전력선 통신용에 적용할 수 있음을 보여주었다. 실험결과 100 A 이하의 선로 전류변동 조건에서 통신거리 100 m 까지는 45 Mbps, 200 m 까지는 8 Mbps의 대역폭을 보였으며 수신율은 100 %이였다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.804-805
• /
• 2006

Electric scroll-compressor drives are commonly used for e.g. home appliance cooling units. The recent development of hybrid cars with internal combustion engine in combination with electrical propulsion requires new solutions to be able to cool the passenger compartment of cars at stand-still. Both application areas demand efficient motor drives to reach good economy and efficient use of limited battery power as well as competitive volume/weight for a given output. The BLDC motor is a controllable and efficient solution. A major part of the motor is the soft-magnetic core. The powder based $Somaloy^{(R)}$ material shows high resistivity and induction as the result of engineered iron particles with in-organic coating. The unique features of compacted $Somaloy^{(R)}$ components can be utilized to enhance the shape and total volume of the BLDC motor with at least maintained efficiency compared to the use of traditional laminated steel sheet cores. A careful design of the $Somaloy^{(R)}$ components can also simplify assembly and positively influence the coil configuration. This study shows a comparison between a typical laminated BLDC motor and a redesigned, $Somaloy^{(R)}$ based version adapted for a scroll-compressor application.