• Journal of the Korean Magnetics Society
• /
• v.4 no.2
• /
• pp.179-183
• /
• 1994

A high efficiency small electromagnet (22 mm air gap and $40{\times}25mm^{2}$ core's cross section) suitable for measuring magnetostriction and magnetic anisotropy was biult. The magnet could be minaturized by reducing the measuring space and time. The excitation current of the electromagnet was supplied for only a few second of measuring time. Cooling system of the electromagnet could be eliminated since the dissipation energy was very small. An 0.5 T magnetic field was generated with 180 W power consumption. The values of magnetostriction and magnetic anisotropy were measured with a very sensitive capacitance cell with resolution of $10^{-8}$ and 1 nJ. The torque was calibrated using a soft magnetic ribbon's shape anisotropy.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.49 no.3
• /
• pp.69-74
• /
• 2012

This paper shows the results about field operating digital hearing aids which protect the ears of the battle field soldiers from explosive sound and minimize the difficulty of mutual communication during the battle. The essence of the hearing aid is in its signal compression technology in which soft sound is amplified while rapidly increased explosive sound is attenuated. This nonlinear compression technology can be applied for the protection of the ears of the battle field soldiers. As a core part of the hearing aid, when a new DSP IC chip is launched, the modified firmware and fitting software is developed for adaption. Ezairo 5910 which was recently launched by DSP factory in Canada was used for the development of the firmware of the hearing aid.

• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.1
• /
• pp.93.2-93.2
• /
• 2012

Point Spread Function (PSF) is one of the most important optical characteristics for describing the performance of a telescope. And a concept of subpixelization is inevitable in evaluating the undersampled PSF (Shin and Sakurai 2009). Then, the internal structure of Yohkoh SXT CCD pixel is not uniform: For the top half of pixel area, the X-ray should pass a so-called gate structure where the charges are transferred to an output amplifier. This gate structure shows energy-dependent sensitivity (Tsuneta et al. 1991). For example, for Al-K (8.34 A) X-ray emission, the transmission of the polysilicon gate is about 0.9. Also, for the peak coronal response of the SXT thin filters, around 17 angstrom (0.729 keV), the transmission of the gate is about 0.6, falling off sharply towards longer wavelengths. It should be noted that this spectrally dependent non-uniform response of each CCD pixel will certainly have a noticeable effect on the properties of the PSF at longer wavelengths. Therefore, especially for analyzing the undersampled PSF of low energy source, a careful consideration of non-uniform internal pixel structure is required in determining the shape of the PSF core. The details on the effect of gate structure will be introduced in our presentation.

• Nuclear Engineering and Technology
• /
• v.50 no.4
• /
• pp.606-612
• /
• 2018

Many nuclear power plants in Japan are approaching the end of their planned operational life spans. They must be decommissioned safely in the near future. Using augmented reality (AR), workers can intuitively understand information related to decommissioning work. Three-dimensional (work-site) reconstruction models of dismantling fields are useful for workers to observe the conditions of dismantling field situations without visiting the actual fields. This study, based on AR and work-site reconstruction models, developed and evaluated an information reference system. The evaluation consists of questionnaires and interview surveys administered to six nuclear power plant workers who used this system, along with a scenario. Results highlight the possibility of reducing time and mitigating mistakes in dismantling fields. Results also show the ease of referring to information in dismantling fields. Nevertheless, it is apparently difficult for workers to build reconstruction models of dismantling fields independently.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.10 no.6
• /
• pp.363-372
• /
• 2015

Recent some SoC FPGA Releases that integrate ARM processor and FPGA fabric show better performance compared to the ASIC SoC used in typical embedded image processing system. In this study, using the above advantages, we implement a SoC FPGA-based Real-Time Object Recognition and Tracking System. In our system, the video input and output, image preprocessing process, and background subtraction processing were implemented in FPGA logics. And the object recognition and tracking processes were implemented in ARM processor-based programs. Our system provides the processing performance of 5.3 fps for the SVGA video input. This is about 79 times faster processing power than software approach based on the Nios II Soft-core processor, and about 4 times faster than approach based the HPS processor. Consequently, if the object recognition and tracking system takes a design structure combined with the FPGA logic and HPS processor-based processes of recent SoC FPGA Releases, then the real-time processing is possible because the processing speed is improved than the system that be handled only by the software approach.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.28 no.6
• /
• pp.793-804
• /
• 1995

Polychaetous community survey in Tomioka Bay was carried out 5 times seasonally from May 1991 to March 1992 by quantitative grab sampling (0.05m2) at 11 stations. Based on the granulometric composition and environmental factors, a homogeneous soft bottom was found in St.5-10. The species of the polychaete were classified into three feeding groups using the Fauchald and Jumars' feeding guild system. According to polychaetous community composition data, deposit feeders predominate in sandy silt area where the silt-clay content is $60-69.3\%.$ These deposit feeders were subdivided into surface deposit feeders and subsurface deposit feeders by their living position and mode. Also, suspension feeding group comes as the third dominant group. Seasonal changes of each feeding group were described in terms of numerical density and biomass. Feeding layer and types of dominant species (Lumbrineris longifolia: surface deposit feeder; Praxillella pacifica: subsurface deposit feeder; Chone duneri; suspension filter feeder, etc.) were examined in the intact sediment core samples. Also, longterm density change among the three dominant species during 10 years was disussed.

• Journal of Power Electronics
• /
• v.16 no.5
• /
• pp.1629-1638
• /
• 2016

Differential power processing (DPP) systems are among the most effective architectures for photovoltaic (PV) power systems because they are highly efficient as a result of their distributed local maximum power point tracking ability, which allows the fractional processing of the total generated power. However, DPP systems require a high-efficiency, high step-up/down bidirectional converter with broad operating ranges and galvanic isolation. This study proposes a single, magnetic, high-efficiency, high step-up/down bidirectional DC-DC converter. The proposed converter is composed of a bidirectional flyback and a bidirectional isolated switched-capacitor cell, which are competitively cheap. The output terminals of the flyback converter and switched-capacitor cell are connected in series to obtain the voltage step-up. In the reverse power flow, the converter reciprocally operates with high efficiency across a broad operating range because it uses hard switching instead of soft switching. The proposed topology achieves a genuine on-off interleaved energy transfer at the transformer core and windings, thus providing an excellent utilization ratio. The dynamic characteristics of the converter are analyzed for the controller design. Finally, a 240 W hardware prototype is constructed to demonstrate the operation of the bidirectional converter under a current feedback control loop. To improve the efficiency of a PV system, the maximum power point tracking method is applied to the proposed converter.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2005.11a
• /
• pp.117-120
• /
• 2005

A Digital Broadcasting Satellite (DBS) receiver converts digital A/V streams received from a satellite to analog NTSC A,/V signals in real-time. Multi-tasking is an efficient way to improve the utilization of the processor core in real-time applications. In this paper, we propose a hybrid approach with a balanced trade-off between hardware kernel and multi-tasking programming to increase a system throughput. First, the schedulability of the critical hard real-time tass in the DBS receiver is verified by using a simple feasibility test. Then. several soft real-time tasks are thoughtfully programmed to satisfy functional requirements of the system.

• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.4
• /
• pp.16-21
• /
• 2008

The demand for three-dimensional (3D) shape measurements is increasing in a variety of fields, including the manufacture of molds and dies. The most popular technology for 3D shape measurement is the coordinate measuring machine (CMM) with a contact trigger probe. Although a CMM provides a high degree of accuracy, it is inefficient due to its long measuring time. It also has difficulty measuring soft objects that can be deformed by the touch of the contact probe. In addition, a CMM cannot digitize areas that are difficult to reach, and cannot capture very minute details on the surface of complex parts. For these reasons, optical non-contact measurement techniques are receiving more attention since they eliminate most of the problems associated with contact methods. Laser scanning is emerging as one of the more promising non-contact measurement techniques. This paper describes various acquisition considerations for laser scanning, including the accuracy of the 3D scan data, which depends on the charge-coupled device (CCD) gain and noise. The CCD gain and noise of a 3D laser scanner are varied while keeping the other conditions constant, and the measurement results are compared to the dimensions of a standard model. The experimental results show that a considerable time savings and an optimum degree of accuracy are possible by selecting the proper CCD gain and noise.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.804-805
• /
• 2006

Electric scroll-compressor drives are commonly used for e.g. home appliance cooling units. The recent development of hybrid cars with internal combustion engine in combination with electrical propulsion requires new solutions to be able to cool the passenger compartment of cars at stand-still. Both application areas demand efficient motor drives to reach good economy and efficient use of limited battery power as well as competitive volume/weight for a given output. The BLDC motor is a controllable and efficient solution. A major part of the motor is the soft-magnetic core. The powder based $Somaloy^{(R)}$ material shows high resistivity and induction as the result of engineered iron particles with in-organic coating. The unique features of compacted $Somaloy^{(R)}$ components can be utilized to enhance the shape and total volume of the BLDC motor with at least maintained efficiency compared to the use of traditional laminated steel sheet cores. A careful design of the $Somaloy^{(R)}$ components can also simplify assembly and positively influence the coil configuration. This study shows a comparison between a typical laminated BLDC motor and a redesigned, $Somaloy^{(R)}$ based version adapted for a scroll-compressor application.