• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.5
• /
• pp.93-99
• /
• 1998

The chirping characteristics of InGaAsP electroabsorption modulatiors have been analyzed. The effective .alpha. parameters for large signal modulation were estimated by comparing the pulse shape after fiber transmission with constant chirping assumption.We investigated the structure and the operating condition of the modulator to improve the chirping characteristics. The .alpha. parameters were calculated as the function of wavelength detuning and the bias voltage. To minimize the chirping performance, high bias voltage and a small wavelength detuning and the bias voltage. To minimize the chirping performance, high bias voltage and a small wavelength detuning were preferred. An negative .alpha. value is achieved at the wavelength detuning below 30meV with a proper bias voltage so that pulse compression effect was expected.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.12 no.1
• /
• pp.75-87
• /
• 2012

A design paradigm using sequential geometric programming is presented to accurately design CMOS op amps with BSIM3. It is based on new adaptive modeling of transistor parameters through the operating point simulation. This has low modeling cost as well as great simplicity and high accuracy. The short-channel dc, high-frequency small-signal, and short-channel noise models are used to characterize the physical behavior of submicron devices. For low-power and low-voltage design, this paradigm is extended to op amps operating in the subthreshold region. Since the biasing and modeling errors are less than 0.25%, the characteristics of the op amps well match simulation results. In addition, small dependency of design results on initial values indicates that a designed op amp may be close to the global optimum. Finally, the design paradigm is illustrated by optimizing CMOS op amps with accurate transfer function.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.3
• /
• pp.612-621
• /
• 1996

In this paper, we propose the low sidelobe digital FIR doppler filter bank synthesis algorithm through the Gradient Descent method and it can be practially appliable to coherent pulse doppler radar signal processing. This algorithm shows the appropriate calculation of tap coefficients or zeros for FIR transversal fiter which has been employed in radar signal processor. The span of the filters in the filter bank be selected at the desired position the designer want to locate, and the lower sidelobe level that has equal ripple property is achieved than one for which the conventional weithtedwindow is used. Especially, when we implemented filter zeros as design parameters it is possible to make null filter gain at zero frequency intensionally that would be very efficient for the eliminatio of ground clutter. For the example of 10 tap filter synthesis, when filter coefficients or zeros are selected as design parameters the corresponding sidelobelevel is reducedto -70db or -100db respectively and it has good convergent characteristics to the desired sidelobe reference value. The accuracy ofapproach to the reference value and the speed of convergence that show the performance measure of this algorithm are tuned out with some superiority and the fact that the bandwidth of filter appears small with respect to one which is made by conventional weighted window method is convinced. Since the filter which is synthesized by this algorithm can remove the clutter without loss of target signal it strongly contributes performance improvement with which detection capability would be concerned.

• ETRI Journal
• /
• v.42 no.6
• /
• pp.922-931
• /
• 2020

A hierarchical iterative algorithm for the canonical polyadic decomposition (CPD) of tensors is proposed by improving the traditional conjugate gradient least squares (CGLS) method. Methods based on algebraic operations are investigated with the objective of estimating the direction of arrival (DoA) and polarization parameters of signals impinging on an array with electromagnetic (EM) vector-sensors. The proposed algorithm adopts a hierarchical iterative strategy, which enables the algorithm to obtain a fast recovery for the highly collinear factor matrix. Moreover, considering the same accuracy threshold, the proposed algorithm can achieve faster convergence compared with the alternating least squares (ALS) algorithm wherein the highly collinear factor matrix is absent. The results reveal that the proposed algorithm can achieve better performance under the condition of fewer snapshots, compared with the ALS-based algorithm and the algorithm based on generalized eigenvalue decomposition (GEVD). Furthermore, with regard to an array with a small number of sensors, the observed advantage in estimating the DoA and polarization parameters of the signal is notable.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.5
• /
• pp.1945-1955
• /
• 2018

High frequency signal injection (HFI) is an alternative method for estimating rotor position of interior permanent magnet synchronous motor (IPMSM). The general method of frequency and amplitude selection is based on error tolerance and experiments, and is usually set with only one group of HF parameters, which is not efficient for different working modes. This paper proposes a novel rotor position estimation scheme by HFI with optimized frequency and amplitude, based on the mathematic model of IPMSM. The requirements for standstill and low-speed operational modes are met by applying this novel scheme. Additionally, the effects of the frequency and amplitude of the injected HF signal on the position estimation results under different operating conditions are analyzed. Furthermore, an optimization method for HF parameter selection is proposed to make the estimation process more efficient under different working conditions according to error tolerance. The effectiveness of the propose scheme is verified by the experiments on an IPMSM motor prototype.

• Journal of Power Electronics
• /
• v.10 no.3
• /
• pp.306-312
• /
• 2010

In this paper, the design of an optimum single input Fuzzy controller for application in dc to ac converters is presented. Contrary to conventional Fuzzy controllers, the proposed controller has a smaller number of rules and tuning parameters but is capable of performing identically to a conventional controller. These benefits lead to a simpler controller design. The controller is designed as a PI controller for small-signal disturbances. However, for optimum large-signal performance, heuristic tuning is used. The tuning is less complicated and hence optimum large-signal performance is achievable. The system is simulated and a hardware prototype was developed for comparison purposes.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.629-632
• /
• 1989

The scattered light intensity from a spherical particle passing through the cross-over region of two coherent laser beams, varies periodically. Photodetection of this light beams produces a periodic signal of varying amplitude. The phase of the signal varies with the particle size and refractive index, the beam crossing angle and wavelength, and the position and size of the scattered ligth collecting aperture. In this paper the phase variation with respect to the particle absorptive index of retraction, collecting lens size and beam crossing angle is calculated using both Mie scattering theory and reflection theory. The two theories show good agreement in phase predictions, especially for large absorptive indices and for small collection lenses. Both theories predict phase to be inversely proportional to the beam crossing angle.

• Journal of Sensor Science and Technology
• /
• v.29 no.5
• /
• pp.324-327
• /
• 2020

The impact of output conductance (g_o) on the short-circuit current-gain cut-off frequency (f_T) in In_0.8Ga_0.2As high-electron-mobility transistors (HEMTs) on an InP substrate was investigated. An attempted was made to extract the values of f_T in a simplified small-signal model (SSM) of the HEMTs, derive an analytical formula for f_T in terms of the extrinsic model parameters of the simplified SSM, which are related to the intrinsic model parameters of a general SSM, and verify its validity for devices with L_g from 260 to 25 nm. In long-channel devices, the effect of the intrinsic output conductance (g_oi) on f_T was negligible. This was because, from the simplified SSM perspective, three model parameters, such as g_{m_ext}, C_{gs_ext} and C_{gd_ext}, were weakly dependent on g_oi. However, in short-channel devices, g_oi was found to play a significant role in degrading f_T as L_g was scaled down. The increase in g_oi in short-channel devices caused a considerable reduction in g_{m_ext} and an overall increase in the total extrinsic gate capacitance, yielding a decrease in f_T with g_oi. Finally, the results were used to infer how f_T is influenced by g_oi in HEMTs, emphasizing that improving electrostatic integrity is also critical importance to benefit fully from scaling down L_g.

• Journal of Biosystems Engineering
• /
• v.25 no.5
• /
• pp.351-358
• /
• 2000

This study was conducted to develop a speed control system of a DC motor which drove a barley seeder mounted on a combine harvester. Barley seeder mounted on a combine has been known to reduce labor and cost of barley cultivation. However, development of the seeder has been unsuccessful because the combine, a dedicated rice and barley harvester has not enough space and proper power take-off for barley seeder. To develop a barley seeder, small powered motor speed controller was required. A proximity sensor for detecting working speed of the combine and a programmable one board microprocessor was used to develope a control system. Motor parameters and motor constant, relationship between seeding rate, motor speed, groove volumes of a tested roller, torque were measured. The proximity sensor sent a frequency signal to the microprocessor. In laboratory experiments, the excitation voltage of the motor was shown not to be proportional to the size of pulse width (duty ratio). A table transforming frequency signal, that represented for working speed to proper pulse width was developed from seeding rate experiments. However, seeding rate at low frequency signal was not proportional to the working speed. Seeding rate control proportional to the frequency signal was achieved by shifting of the frequency signal.

• Journal of Korean Society for Quality Management
• /
• v.27 no.1
• /
• pp.165-194
• /
• 1999

Taguchi's parameter design seeks proper choice of levels of controllable factors (Parameters in Taguchi's terminology) that makes the qualify characteristic of a product optimal while making its variability small. This aim can be achieved by response surface techniques that allow flexibility in modeling and analysis. In this article, a collection of response surface modeling and analysis techniques is proposed to deal with the multiresponse optimization problem in experimentation with Taguchi's signal and noise factors.