• 한국군사과학기술학회지
• /
• 제21권2호
• /
• pp.195-203
• /
• 2018

Among the techniques of reducing the drag to increase the speed of underwater moving bodies, we studied on the drag reduction method by gas injection. Researches on gas injection method have been paid much attention to reduce the drag of vessels or pipe inner walls. In this study, we used a sintered metal mesh that can uniformly distribute fine bubbles by gas injection method, and applied it to a cylindrical underwater moving body. Using the KRISO medium-sized cavitation tunnel, we measured both the bubble size on the surface of the sintered mesh and the bubble distribution in the boundary layer. Then, drag reduction tests were performed on the cylinder type underwater moving models with cylindrical or round type tail shape. Experiments were carried out based on the presence or absence of tail jet injection. In the experiments, we changed the gas injection amount using the sintered mesh gas injector, and changed flow rate accordingly. As a result of the test, we observed increased bubbles around the body and confirmed the drag reduction as air injection flow rate increased.

• 한국세라믹학회지
• /
• 제32권3호
• /
• pp.289-294
• /
• 1995

As the results of the study on the effects of mixing time for raw materials to the electric and magnetic properties of Mg-ferrite, the fraction of spinel phase after calcination and the geometry density of sintered Mg-ferrite increased from 30% to 100% and from 2.5g/cc to 4.25g/cc respectively due to mixing-homobenity of raw materials. The AC resistivity of grains decreased and lattice parameter, saturation magnetization increased due to the increase in Fe+2 of sintered body. conclusively the characteristic of powder after calcination had strong influence on the microstructure, electric, and magnetic properties in Mg-ferrite sintered body.

• The Korean Journal of Ceramics
• /
• 제4권2호
• /
• pp.99-102
• /
• 1998

Cordierite ceramics with low dielectric constants were obtained through sol-gel techniques using as metal alkoxides. The powders for the sintered cordierite ceramics were prepared by hydrolysis of metal alkoxides with ethanol and distilled water. In the hydrolysis, the mole ratio of HCI/TEOS was controlled by changing the amount of HCI as a catalyst. The sol-gel derived powders were dried, pressed, and fired at $1300^{\circ}C$. The dried powders were calcined at $800{\circ}C$ for 3hours to remove residual organics. The fired bodies with different dielectric constants were obtained by using HCI adjusted to various mole ratios of HCI/TEOS in the process. The variation of the amount of HCI catalyst led to a significant influence on dielectric contant, which was attributed to the formation of pores in the sintered body. Especially, the porosity of the sintered body influenced the dielectric constants.

• 한국자기학회지
• /
• 제4권2호
• /
• pp.89-93
• /
• 1994

Mg-페라이트에 있어서 B-H hysteresis loop 특성에 미치는 소결체의 밀도, 내부 응력, 입자 크기의 영향을 조사하였다. 밀도가 증가함에 따라서 보자력은 감소하였으며 각형비는 증가 하였다. 보자력은 내부 응력에 매우 의존적이었으며 시편 내부에 응력이 존재할때 보자력은 1.95 [Oe]에서 4.35[Oe]로 증가하였다. 그러나 각형비는 큰 차이가 없었다. 입자 크기가 6-11[um] 범위 내에서의 보자력 및 각형비는 입자 크기에 의존성을 갖지 않았다.

• 한국세라믹학회지
• /
• 제31권6호
• /
• pp.595-600
• /
• 1994

Ni0.3Zn0.7Fe2O4 ferrite specimens were fabricated by dry pressing and tape casting method. The properties of each specimen were measured and compared. In order to design and manufacture the chip devices effectively, one important criterion can be that the sintered density of the laminated body should approach close to that of the dry pressed body which is regarded as standard. This requirement could be satisfied by controlling the solid loading of the ferrite sheet, lamination temperature and pressure. Using the optimum conditions (solid loading 55 wt%, lamination temperature 6$0^{\circ}C$, lamination pressure 400 kg/$\textrm{cm}^2$, sintered at 125$0^{\circ}C$ 2h) a sintered ferrite, with the density of 5.18g/㎤ and permeability of 1390 at 0.5 MHz, were obtained.

• 한국세라믹학회지
• /
• 제40권7호
• /
• pp.677-682
• /
• 2003

석탄회.점토의 무게비가 7 : 3인 슬립에 대하여 그 해교정도에 따라 slip을 F(Flocculated), M(Moderate) 및 D(Dispersed)의 3종류로 제조하고 이로부터 소결체를 합성하여 시편의 물성과 슬립 특성과의 관계를 분석하였다. Slip F는 응집입자의 크기분포가 넓은 반면 slip D는 입도분포가 좁고 11 $\mu\textrm{m}$ 이상의 큰 응집입자가 거의 존재하지 않았다. 성형체의 기공은 슬립의 종류에 관계없이 1~4 $\mu\textrm{m}$ 범위 내에 분포하며 소결 후에는 1 $\mu\textrm{m}$ 이하의 미세기공은 거의 소멸된 반면, 큰 기공은 1 $\mu\textrm{m}$ 정도 더 성장하였다. Slip F의 경우에 소결 후 기공분포는 slip M과 D에 비하여 주피크의 높이가 높고 폭이 좁았으며, large pore limit (가장 큰 기공 크기)가 5.1 $\mu\textrm{m}$로 다른 슬립 성형체보다 작았다. 입자가 잘 분산된 슬립(slip D)보다는 약간 응집된 슬립(slip F)이 소결시 시편내 거대기공의 생성을 억제함으로서 높은 압축강도를 얻는데 유리하였다. 이상의 결과로부터 소결체의 기계적 특성은 기공분포에 크게 의존하며, 이는 슬립의 분산특성을 제어함으로서 가능함을 알 수 있다.

• 한국세라믹학회지
• /
• 제30권5호
• /
• pp.381-388
• /
• 1993

Due to the anisotropy of thermal expansion, LAS system which has low thermal expansion property is hard to obtain a dense sintered body. Therefore, the thermal expansion coefficient and the mechanical strength were decreased. In this study, mullite, which has good mechanical properties in high temperature and comparatively low thmeral expansion coefficient, was taken as a additive in LAS system. And then, sintering, thermal, and mechanical properties were investigated. The results are follows; When mullite is added in eucryptite composition (Li2O.Al2O3.2SiO2) of LAS system, the creation of liquid phase results in the densification of sintered body and the specimen sintered at 136$0^{\circ}C$ for 2 hours shows optimum sintering condition. With the addition of mullite in eucryptite composition, mechanical strength is increased by the control of grain growth. Especially, flexual strength of EM0 specimen was about double value than the basic composition. Thermal expansion coefficients of EM0 and EM15 specimens sintered at 136$0^{\circ}C$ were -8.23$\times$10-6/$^{\circ}C$ and -4.90$\times$10-6/$^{\circ}C$ in the temperature range of RT.~80$0^{\circ}C$. As the mullite content are increased, negative thermal expansion ratios are decreased.

• 한국분말재료학회지
• /
• 제11권6호
• /
• pp.528-534
• /
• 2004

Using the nano Fe powders having 50 nm in diameter, Fe compact bodies were fabricated by injec-tion molding process. The relationship between microstructure and material properties depending on the volume ratio of powder/binder and sintering temperature were characterized by SEM, TEM techniques. In the compact body with the volume percentage ratio of 45(Fe powder) : 55(binder), which was sintered at $700^{\circ}C,$ the relative density was about $97{\%},$ and the values of volume shrinkage and hardness were about $66.3{\%}$ and 242.0 Hv, respec-tively. Using the composition of 50(Fe powder) : 50(binder) and sintered at $700^{\circ}C,$ the values of relative density, volume shrinkage and hardness of Fe sintered bodies were $73.3{\%},\;47.6{\%}$ and 152.8 Hv, respectively. They showed brittle fracture mode due to the porous and fine microstructure.

• 자원리싸이클링
• /
• 제10권4호
• /
• pp.24-33
• /
• 2001

For making a high degree of efficiency, this study attempts to gather each arisen-sludge from experiments and examine into its characteristics, in order to compare the biological reason of removing phosphorus with sintered body using calcite and the artificial reason of removing with a chemical reagent. First, it can be seen that sludge, which is identified CaCO$_3$, of 0.1∼0.2$\mu$m is regularly formed when using sintered body, calcite. And it is one of the results of the chemical methods in order to remove phosphorus that can be seen that sludges of 100∼50 $\mu$m are formed and that the forms of Ca$_2$P$_2$O$\_$7/, Ca$_3$(PO$_4$)$_2$$.$nH$_2$O, $\beta$-Ca$_2$P$_2$O$\_$7/ are shown when using a reagent, CaO dissolved water. The other of the results of the chemical methods can be seen that a lumpof sludge is formed when using wastewater and a reagent Ca$^2$$\^$+/ are used, and that the lump consists of Ca$_3$(PO$_4$)$_2$$.$nH$_2$O와 Ca$_2$H$_2$P$_4$O$\_$14/.

• 자원리싸이클링
• /
• 제9권4호
• /
• pp.56-62
• /
• 2000

본 연구에서는 하.폐수 처리를 효과적으로 할 수 있도록 각종 비금속 광물들을 혼합하여 부착성 및 토양 미생물의 활동을 촉진시킬 수 있게 광물 소결체를 이용한 합병정화조를 도입하여 주택용 소규모의 생활 하수를 발생원에서 바로 처리하기 위하여 단독주택 2가구를 대상으로 소규모형 무산소-호기 공정 합병정화조 실험 장치를 설치하여 실험하였다. 그 결과 COD.BOD의 방류수는 10mg/l 전후로 나타났고 총질소 (T-N)는 60~70% 정도까지 제거시킴으로 인해 외부에서 탄소원을 첨가하지 않고도 탈질을 할 수 있음을 확인 할 수 있었다. 또한 춤인(T-P)은 80%이상의 제거 효율을 나타내어 생물학적 처리 가능성을 확인할 수 있었다.