• Journal of Power Electronics
• /
• v.11 no.3
• /
• pp.285-293
• /
• 2011

This paper proposes two SRM driving systems using a variable dc-link voltage controlled by a single-phase inverter. Two SRM converter topologies of a half bridge type and a full bridge type are proposed according to the power circuits of an inverter. The phase current can be controlled by means of a PWM controller at the inverter, and the turn-on/off angle at the phase switches can be controlled by a position sensor at the converter in the drive system. The inverter acts as a peak-current limiter if the transient current exceeds its maximum value. SRMs using the proposed topologies maintain high efficiency due to energy regeneration after the turn-off of power switches. The operational modes of the proposed topologies are verified by simulation and experimental results.

• Structural Engineering and Mechanics
• /
• v.25 no.6
• /
• pp.653-674
• /
• 2007

This paper discusses the application of piezoelectric sensors used for evaluation of damping ratio of PVC plastics. The development of the mathematical formulation based on the Empirical Mode Decomposition for calculating the damping coefficient and natural frequency of the system is presented. A systematic experimental and analytical investigation was also carried out to demonstrate the integrity of several methods commonly used to evaluate the damping of materials based on a single degree freedom formulation. The influence of the sensors' location was also investigated. Besides the commonly used methods, a newly emerging time-frequency method, namely the Empirical Mode decomposition, is also employed. Mathematical formulations based on the Hilbert-Huang formulation, and a frequency spacing technique were also developed for establishing the natural frequency and damping ratio based on the output voltage of a single piezoelectric sensor. An experimental investigation was also conducted and the results were compared and verified with Finite Element Analysis (FEA), revealing good agreement.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.2
• /
• pp.75-78
• /
• 2017

We reports improved monitoring performance of Self plasma-optical emission spectroscopy (SP-OES) by augmenting a by-pass tube to a conventional straight (or single) tube type self plasma reactor. SP-OES has been used as a tool for the monitoring of plasma chemistry indirectly in plasma process system. The benefits of SP-OES are low cost and easy installation, but some semiconductor industries who adopted commercialized SP-OES product experiencing less sensitivity and slow sensor response. OH out-gas chemistry monitoring was performed to have a direct comparison of a conventional single type tube and a by-pass type tube, and fluid dynamic simulation on the improved hardware design was also followed. It is observed faster pumping out of OH from the chamber in the by-pass type SP-OES.

• Proceedings of the Korean Society of Computer Information Conference
• /
• 2023.07a
• /
• pp.67-68
• /
• 2023

본 논문에서 제안한 Multi Agent Multi Action은 기존의 대화형 시스템 방식인 Single Agent Single Action 구조에 비해 확장성을 갖춘 대화 시스템을 구현하는 방식이다. 시스템을 여러 에이전트로 분할하고, 각 에이전트가 특정 액션에 대한 처리를 담당함으로써 보다 유연하고 효율적인 대화형 시스템을 구현할 수 있으며, 다양한 작업에 특화된 에이전트를 그룹화함으로써 작업의 효율성을 극대화하고, 사용자 경험을 향상 시킬 수 있다.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.12
• /
• pp.142-149
• /
• 2015

Most of the mono-camera based lane detection systems are fragile on poor illumination conditions. In order to compensate limitations of single sensor utilization, lane information fusion system using multiple lane sensors is an alternative to stabilize performance and guarantee high precision. However, conventional fusion schemes, which only concerns object detection, are inappropriate to apply to the lane information fusion. Even few studies considering lane information fusion have dealt with limited aids on back-up sensor or omitted cases of asynchronous multi-rate and coverage. In this paper, we propose a lane information fusion scheme utilizing multiple lane sensors with different coverage and cycle. The precise lane information fusion is achieved by the proposed fusion framework which considers individual ranging capability and processing time of diverse types of lane sensors. In addition, a novel lane estimation model is proposed to synchronize multi-rate sensors precisely by up-sampling spare lane information signals. Through quantitative vehicle-level experiments with around view monitoring system and frontal camera system, we demonstrate the robustness of the proposed lane fusion scheme.

• Journal of Sensor Science and Technology
• /
• v.12 no.2
• /
• pp.79-87
• /
• 2003

In this paper, we propose a method to obtain a linear characteristic using soft computing for systems which have array sensors of nonlinear characteristics. Also a procedure utilizing the pattern information of array sensors without additional sensors is proposed to reduce disturbance effects. For a typical example, even a single CdS cell for CdS array has nonlinear characteristics. Overall linear characteristic for CdS array is obtained using fuzzy logic for each cell and overlapped portion. In addition, further improvement for linearization is obtained applying genetic algorithms for the parameters of membership functions. Also the effect of disturbing external light changes to the CdS array can be reduced without using any additional sensors for calibration. The proposed method based on fuzzy logic shows improvements for position measurements and disturbance reduction to external light changes due to the fuzziness of the shadow boundary as well as the inherent nonlinearity of the CdS array. This improvement is shown by applying the proposed method to the ball position measurements of a magnetic levitation system.

• Journal of Biosystems Engineering
• /
• v.34 no.2
• /
• pp.95-105
• /
• 2009

A method was proposed which employed control of the drop location of fertilizer particles on a spinner disc to optimize the spread pattern uniformity. The system contained an optical sensor as a feedback mechanism, which measured discharge velocity and location, as well as particle diameters to predict a spread pattern of a single disc. Simulations showed that the feed gate adaptation algorithm produced high quality patterns for any given application rate in the dual disc spreader. The performance of the feed gate control method was assessed using data collected from a Sulky spinner disc spreader. The results showed that it was always possible to find a spread pattern with an acceptable CV lower than 15%, even though the spread pattern was obtained from a rudimentary flat disc with straight radial vanes. A mathematical optimization method was used to find the initial parameter settings for a specially designed experimental spreading arrangement, which included the feed gate control system, for a given flow rate and swath width. Several experiments were carried out to investigate the relationship between the gate opening and flow rate, disc speed and particle velocity, as well as disc speed and predicted landing location of fertilizer particles. All relationships found were highly linear ($r^2$ > 0.96), which showed that the time-of-flight sensor was well suited as a feedback sensor in the rate and uniformity controlled spreading system.

• Transactions on Control, Automation and Systems Engineering
• /
• v.4 no.2
• /
• pp.114-123
• /
• 2002

Called VISTA (Variable-stability In-flight Simulator Test Aircraft), the one-of-a-kind NF-l6D has a simulation system that can mimic several aircraft. Though housed in an F-l6 Fighting Falcon airframe, VISTA can also act like the F-15 Eagle or the Navy's F-14 Tomcat. More importantly, such flexibility allows for improved training and consolidation of some sorties. Consequently USAF Test Pilot School students will have an opportunity to learn how to test future integrated cockpits. In this paper we will use the multiple model adaptive estimation (MMAE) and the multiple model adaptive controller (MMAC) techniques to model the aircraft's flight control system containing the longitudinal and lateral-directional axes. Single and dual actuator and sensor failures will also be included in the simulation. White Gaussian noise will be included to simulate the effects of atmospheric disturbances.

• Journal of Institute of Control, Robotics and Systems
• /
• v.6 no.5
• /
• pp.415-425
• /
• 2000

An open architecture manufacturing strategy intends to integrate manufacturing components on a single platform so that a particular component can be easily added and/or replaced. Therefore, the control scheme based upon the open architecture concept is hardware-independent. In this paper, a modular and object oriented approach for a PC-based open robot control system is investigated. A standard reference model for robot systems, which consists of three modules; hardware module, operating system module, and application software module, is first proposed. Then, a PC-based Open Robot Controller(PC-ORC), which can reconfigure robot control systems in various production environments, is developed. The PC-ORC is built upon the object-oriented method, and allows an easy implementation and modification of various modules. The PC-ORC consists of basic softwares, application objects, and additional hardware device on the PC Platform. The application objects are: sequencer, computation unit, servo control, ancillary equipment, external sensor control, and so on. In order to demonstrate the applicability of the PC-ORC, the proposed PC-ORC configuration is applied to an industrial SCARA robot system.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.541-542
• /
• 2006

In this paper, I propose the field emission tip for the E-beam array system that is made by carbon nanotubes(CNT). CNT is one of the most expected future materials, because of its great mechanical, chemical and electrical characteristics. So CNT can be used for many applications such as electron emitter, sensor, single electron transistor and AFM tip. And CNT will be applied to our E-beam array system as field emission tip so we will improve the system's electrical characteristics.