• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 B
• /
• pp.585-587
• /
• 1999

The rotorbody and rotor winding of generator are isolated by an insulator and the output characteristic of the generator is maintained in the best states. Only when an insulation resistance between them is over a certain extent. The aim of this research is to develop the simulator for rotor earth fault detection circuits. It is composed of the power resource which is to control the virtual field voltage, stepping motor which is to give virtual ground. It is possible to inspect with the device and program developed in this study in the same as real operating condition and evaluate the integrity of generator rotor through the function of data acquisition and graphic output. If these technologies will be applied to the inspection, prevent a damage of the generator and contribute to improve maintenance reliance.

• 전기학회논문지
• /
• 제59권6호
• /
• pp.1046-1052
• /
• 2010

In residential house, photovoltaic (PV) system among various alternatives in renewable energy system is the most efficient and feasible solution for reducing energy consumption and electricity cost. However, relatively high initial cost make people reluctant to install PV system in their houses. Therefore, in the initial state for PV system installation in the house, it is very important to decide proper capacity of the PV system considering the expected energy usage and solar energy supplying condition with the house. This paper proposes a novel optimization model for deciding appropriate capacity of the PV system for residential house. The objective function of the model is to minimize the annual cost including electricity bill, operation and maintenance cost, and annual fixed cost calculated from the initial installation cost based on capital recovery factor (CRF). The model also shows the optimal inclining angle of PV panels of the system. In this paper, we estimate the PV output using PVWATTS (PV simulator of Office of Energy Efficiency and Renewable Energy) and find optimal solutions by Sequential Quadratic Programming (SQP) method using MATLAB software. The proposed approach is finally applied to a residential model house in Gangneung, Gangwon-Do and verified its feasibility for adopting to PV system design for residential houses.

• 전기학회논문지P
• /
• 제62권3호
• /
• pp.117-126
• /
• 2013

This paper is written for the development and application of boiler furnace pressure control algorithm and distributed control system of coal-fired power plant by the steps of design, coding, simulation test, site installation and site commissioning test. The control algorithms were designed in the shape of cascade control for two parts of furnace pressure control and induced draft fan pitch blade by standard function blocks. This control algorithms were coded to the control programs of distributed control systems. The simulator for coal-fired power plant was used in the test step and automatic control, sequence control and emergency stop tests were performed successfully like the tests of the actual power plant. The reliability was obtained enough to be installed at the actual power plant and all of distributed control systems had been installed at power plant and all signals were connected mutually. Tests for reliability and safety of plant operation were completed successfully and power plant is being operated commercially. It is expected that the project result will contribute to the safe operation of domestic new and retrofit power plants, the self-reliance of coal-fired power plant control technique and overseas business for power plant.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전력기술부문
• /
• pp.30-34
• /
• 2005

Due to old Toshiba EMS's database size limit and hardware old aging, KPX(Korea Power Exchange) had introduced New EMS from AREVA(old ALSTOM) in July 2002. After then KPX had committed many man power and time to normalize EMS NA(Network Analysis) functions for using real power system. At initial stage, to normalize State Estimator which is the backbone of all other NA functions and DTS(Dispatcher Training Simulator}, KPX had corrected numerous topology errors, network model errors, non-scanned and wrongly scanned SCADA measured errors. After SE function study, running test and tuning, State Estimator could finally have been run properly and stably from June 2003. Based on SE running, KPX had normalized real time Contingency Analysis, and study mode Power Flow, STNET and DTS. From early 2004, dispatchers have been trained to use NA and DTS for the purpose of stable SE running, NA operation & results reading and urgent equipment outage reviewing. EMS NA have been greatly contributed to operate real time power system stably. Above NA normal operation by KPX own efforts under the no experience of NA running, KPX made a good precedent. This paper is intended to introduce EMS NA normalization process, operation status, and etc in Korea power system operation.

• Korean Chemical Engineering Research
• /
• 제43권4호
• /
• pp.474-481
• /
• 2005

본 연구에서는 공비점 분리제로써 벤젠을 사용하고 3기의 증류탑을 이용해서 에탄올 수용액으로부터 거의 순수한 무수 에탄올을 생산해 내는 공비증류공정에 대한 모델링과 최적화 작업을 수행하였다. 공비증류공정의 모사를 위한 열역학 모델식으로는 NRTL 액체 활동도계수 모델식을 사용하였으며 상용의 화학공정 모사기인 PRO/II with PROVISION 6.01을 사용하였다. 최적화 작업을 위한 목적함수로는 각 증류탑 재비기의 Heat duty로 정하였으며 농축기 탑상제품의 에탄올의 농도를 최적화 변수로 정하였다. 농축기 탑상 제품에서 에탄올 몰농도가 76 mole％일 때 증류탑의 재비기의 Heat duty의 합이 최소가 됨을 알 수 있었다.

• Journal of Communications and Networks
• /
• 제7권3호
• /
• pp.377-384
• /
• 2005

The purpose of this research is to develop and evaluate a traffic engineering architecture that uses local state information. This architecture is applied to an Internet protocol radio access network (RAN) that uses multi-protocol label switching (MPLS) and differentiated services to support mobile hosts. We assume mobility support is provided by a protocol such as the hierarchical mobile Internet protocol. The traffic engineering architecture is router based-meaning that routers on the edges of the network make the decisions onto which paths to place admitted traffic. We propose an algorithm that supports the architecture and uses local network state in order to function. The goal of the architecture is to provide an inexpensive and fast method to reduce network congestion while increasing the quality of service (QoS) level when compared to traditional routing and traffic engineering techniques. We use a number of different mobility scenarios and a mix of different types of traffic to evaluate our architecture and algorithm. We use the network simulator ns-2 as the core of our simulation environment. Around this core we built a system of pre-simulation, during simulation, and post-processing software that enabled us to simulate our traffic engineering architecture with only very minimal changes to the core ns-2 software. Our simulation environment supports a number of different mobility scenarios and a mix of different types of traffic to evaluate our architecture and algorithm.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제7권2호
• /
• pp.110-119
• /
• 2007

A new two-dimensional analytical model for dual-material double-gate fully-depleted SOI MOSFET with Pearson-IV type Doping Distribution is presented. An investigation of electrical MOSFET parameters i.e. drain current, transconductance, channel resistance and device capacitance in DM DG FD SOI MOSFET is carried out with Pearson-IV type doping distribution as it is essential to establish proper profiles to get the optimum performance of the device. These parameters are categorically derived keeping view of potential at the center (${\phi}_c$) of the double gate SOI MOSFET as it is more sensitive than the potential at the surface (${\phi}_s$). The proposed structure is such that the work function of the gate material (both sides) near the source is higher than the one near the drain. This work demonstrates the benefits of high performance proposed structure over their single material gate counterparts. The results predicted by the model are compared with those obtained by 2D device simulator ATLAS to verify the accuracy of the proposed model.

• 센서학회지
• /
• 제6권2호
• /
• pp.145-154
• /
• 1997

회로 시뮬레이션과 국부적 탐색을 갖는 시뮬레이티드 아닐링을 사용한 새로운 탐색 전략에 기초하여 고성능 연산 증폭기의 설계 자동화를 위한 기법을 제안하였다. 임의의 연산 증폭기 구조와 성능 규격에 대해서, 이산 설계 변수들을 갖는 비용 함수의 이산 최적화를 통해 연산 증폭기의 설계가 이루어진다. 설계 시간의 단축을 위해서 전용 회로 시뮬레이터와 몇 가지 휴리스틱을 사용하였다. 스마트 센서와 10 비트 25 MS/s 파이프라인 A/D 변환기에 사용 가능한 저전력 고속 전차동 CMOS 연산 증폭기의 설계를 통해서, 제안된 기법을 사용하여 개발된 설계 도구는 적은 설계 지식과 설계 노력을 가지고 고성능 연산 증폭기를 설계하는데 사용될 수 있음을 보였다.

• 한국전기전자재료학회논문지
• /
• 제28권8호
• /
• pp.486-489
• /
• 2015

Power semiconductor device has a very long history among semiconductor, since the invention of low-pressure bipolar transistor 1947, and so far from small capacity to withstand voltage-current, high-speed and high-frequency characteristics have been developed with high function. In this study, the PWM IC Switch to the main parts used in IGBT (insulated gate bipolar transistor) for the low power loss and high drive capability of the simulator to Synopsys' T-CAD used by the 1,700 V NPT Planar IGBT, 1,700 V FS was a study of the Planar IGBT, the results confirmed that IGBT 1,700 V FS Planar is making about 11 percent less than the first designed NPT Planar IGBT.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2015년도 제46회 하계학술대회
• /
• pp.247-248
• /
• 2015

Wind turbines causes instabilities on the grid as their penetration increase. To mitigate harmful effects from wind turbines, transmission system operator(TSO) set up some requirements to obligate for wind generation operator for grid connection. So wind farm management system(WFMS) has important role to follow requirement from TSO, WFMS calculates available real power by considering wake effects, and dispatches real power order to each wind turbine in wind farm to optimize for decreasing load fatigue. To verify operation of WFMS, real-time simulator(RTS) is necessary. This paper deals with RTS configuration to verify WFMS operation. RTS includes wind farm model and power flow code. Normally, wind farm equivalent simple model makes wind turbines in wind farm to one wind turbine mode which cannot verify power flow in wind farm and WFMS operation. Thus, this paper makes wind farm model using simple wind turbine model with transfer function. Matlab is used for make power flow code and wind farm model to impose RTS and those model is certified by PSCAD/EMTDC.