• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.3
• /
• pp.54-59
• /
• 2017

GGBFS (Ground Granulated Blast Furnace Slag) is a byproduct with engineering advantages and HVSC (High Volume Slag Concrete) is widely attempted due to active utilization and reduction of eco-load. In the present work, characteristics of drying shrinkage and early-aged behavior are evaluated for the concrete with 65% replacement ratio of GGBFS and 50MPa of design strength. For the work, 3 different mix conditions are considered and several tests including slump flow, compressive strength, drying and autogeneous shrinkage are performed. From the test, OPC 100 mixture without replacement shows higher strength development before 7 days, however the strength reduction in concrete replaced with GGBFS is not significant due to sufficient free water for cement hydration. OPC 100 mixture also shows significant drying shrinkage due to a great autogeneous shrinkage before 3 days. In the concrete with GGBFS replacement, the drying shrinkage behavior is improved due to relatively small deformation by autogeneous shrinkage. The mixture (OPT BS 65) with lower w/b ratio (0.27) and unit content of water ($160kg/m^3$) shows more improved shrinkage behavior than BS 65 mixture which has simple replacement of GGBFS with 0.30 of w/b and $165kg/m^3$ of water unit content.

• Economic and Environmental Geology
• /
• v.43 no.6
• /
• pp.615-623
• /
• 2010

Seismic refraction survey is a geophysical method that delineates subsurface velocity structure using direct wave and critically refracted wave. The generalized reciprocal method(GRM) is an inversion technique which uses travel-time data from several forward and reverse shots and which can provide the geometry of irregular inclined refractors and structures underlain by hidden layer such as low velocity zone and thin layer. In this study, a simple Excel-GRM routine was tested for fast mapping of the interface between weathering layer and bedrock during the survey, with employing a pair of forward and reverse shots. This routine was proved to control the maximum dip of approximately $30^{\circ}C$ and maximum velocity contrast of 0.6, based on the panel tests in terms of dipping angle and velocity contrast for the two-layer inclined models. In contrast with conventional operation of five to seven shots with sufficient offset distance and indoor data analysis thereafter, this routine was performed in the field shortly after data acquisition. Depth to the bedrock provided by Excel-GRM, during the field survey for Cheongju granite area, correlates well with the elevation of the surface of soft rock from the drill core and SPS logging data. This cost-effective routine developed for quickly delineating the bedrock surface in the field survey will be readily applicable to mapping of weathering zone in narrow zone with small variation of elevation of bedrock.

• Journal of Veterinary Clinics
• /
• v.30 no.2
• /
• pp.146-149
• /
• 2013

A 6-month-old, intact male Great Pyrenees (35 kg) was referred with 2 weeks continuous left forelimb lameness to the Chonbuk Animal Medical Center, College of Veterinary medicine, Chonbuk National University. The lameness became worse three days before being referred to the hospital. Upon the physical examination, the patient had pain when the left shoulder joint was palpated, and the lameness was visible in the left forelimb during ambulation on gait examination. There were no remarkable findings on radiological and neurological examination. Osteochondritis dissecans (OCD) was suspected based on medical history and gait tests. As a definitive diagnosis could not be made, exploratory arthroscopic surgery was performed to examine the inside of the shoulder joint. During the operation, mild bicipital tenosynovitis, synovitis and OCD which was located on the caudal medial area of humeral head were revealed. Arthroscopic procedures were used for the treating OCD, including the removal of the OCD flap and debriding of the subchondral defect until hemorrhaging by use of an electrical burr. The patient was discharged a day after surgery. After 2 weeks, the patient again presented at the hospital due to complications, including inflammation of the surgical lesion because of licking and seroma within the subcutaneous tissue. Antibiotics were administered and an aseptic bandage was applied. And simple surgical operations were performed for the removal of the cyst and seroma. Eleven weeks following arthroscopy, the lameness was completely resolved. Arthroscopy has the advantage of allowing gross examination inside the joint capsule. Due to this advantage, arthroscopy is one of the best advanced options for diagnosis in dogs with undiagnosed joint pain.

• Korean Journal of Microbiology
• /
• v.38 no.3
• /
• pp.205-212
• /
• 2002

This study was conducted to develop a method for direct determination of phagocytic activities in human circulatic systems and to measure the phagocytic activities in human leukocytes from the alcoholics, since phagocytic activity was considered to be very important in human immune mechanism at early stage for the health care of the alcoholics. The subjects for this study were 130 among which 95 males and 3 females were diagnosed as alcoholism and 32 was healthy blood donors. A thin layer of heat-killed Staphylococcus aureus Cowan I was placed on a plastic dish and reacted with whole blood to measure the phagocytic plaque formation by human leukocytes. In order to determine the health conditions of the subjects, some clinical laboratory tests, such as white blood cell counts, hemoglobin contents (Hgb), mean corpuscular volume of red blood cells(MCV), serum electrophoresis, B and T-lymphocytes, T-lymphocyte subtypes and phytohemagglutination test were also implemented. Compared to the non-alcoholism, new and old alcoholic inpatients showed statistically significant differences on levels of Hgb and MCV (p<0.05), but showed that T and B-lymphocyte numbers decreased and Helper T cell/Suppressor T cell ratio ($1.6{\pm}0.8$%) increased. Compared to non-alcoholism, phagocytic plaque activities of leukocytes from alcoholic patients decreased significantly and an unusual pattern in phagocytic plaque was observed, showing a strange body and chain shaped phagocytosis. Based upon these results, it is concluded that a phagocytic-plaques of Staphylococcus aureus Cowan I by leukocytes was very simple and useful method for the early immunological determination of phagocytic activities in alcoholic patients without requiring any special equipments.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.28 no.1
• /
• pp.51-60
• /
• 2018

Objectives: Currently, there is only limited knowledge regarding the hazard of low-level exposure to CMR materials in workplaces. To overcome this limitation, a reference concentration for workers($RfC_w$) from among the risk assessment tools proposed by the US EPA is widely used to set a provisional workplace exposure level(PWEL) for CMR materials for which there are no established Korea Occupational Exposure Limits(KOELs) or subjective chemicals for work environment measurements as regulated by Korea Ministry of Employment and Labor(KMOEL). A simple European calculator of derived no effect level(SECO-DNEL) as proposed by REACH can also be used in place of $RfC_w$ to set the PWEL for chemicals. This study was performed to test the acceptability of using SECO-DNEL as an alternative to $RfC_w$ when setting a PWEL for low-level exposures. Methods: The $RfC_w$ and DNEL for the five CMR materials of dinitrogen oxide, catechol, 2-phenoxy ethanol, carbitol, and carbon black were calculated using the dose-response assessments of the US EPA for $RfC_w$ and REACH guidance for SECO-DNEL, respectively. They were compared using paired t-tests to determine the statistical differences between them. Results: For the five chemicals, the $RfC_w$ were 2.53 ppm, 0.10 ppm, 1.73 ppm, 1.66 ppm, and $0.05mg/m^3$, respectively, while the SECO-DNEL were 2.01 ppm, 0.11 ppm, 1.83 ppm, 1.77 ppm, $0.14mg/m^3$, respectively. There was no statistically significant difference between $RfC_w$ and SECO-DNEL. Conclusions: This study suggests that the SECO-DNEL could be applied in place of $RfC_w$ to set a PWEL for low-level exposure to chemicals, especially CMR materials. To further ensure the reliability of SECO-DNEL as an alternative tool, more chemicals should be applied for calculation and comparison with $RfC_w$.

• Journal of the Korean Society for Precision Engineering
• /
• v.3 no.2
• /
• pp.62-75
• /
• 1986

An experimental investigation of the machining characteristics such as cutt- ing resistance, surface roughness and tool wear in turning the test pieces of SM45C steel with both coated and uncoated carbide tool tips under various cutting conditions was conducted. Also a specially designed simple vibration damping device was experimentally evaluated for its effectiveness on machined surface roughness and a vibration test was conducted to confirm its ability to reduce the amplitude. Based on these tests finding, the following conclusions are made; 1. The cutting resistance($\textrm{p}_{1}$) increases as the depth of cut(d) increases at fixed feed rate(f) over the cutting speed(v) range of 43-226 m/min and p decreses about 18% average when V is increased for fixed d and f. At V= 226m/min, $\textrm{p}_{1}$/for A, C tips are about the same level but $\textrm{p}_{1}$ for B tip is 15% less than A, C tips. 2. The specific cutting resistance(Ks) at V=226 m/min was derived for A, B, C tips respectively and the value of Ks for B rip is about 20% less than A, C tips. 3. The surface roughness(Ra) improves significantly as the cutting speed(V) is increased and this effect was greater when V>100 m/min. On the other hand, Ra deteriorates as the feed rate(f) is increased and this trend was accelerated when f>0.3 mm/rev. With regard to the difference of Ra values among A, B, C tips, at V=226m/min, d=0.4mm, and f=0.31-0.61mm/rev, Ra values for B.C tips are about 17% less than tip A. 4. The experimental tool wear equations were derived for A, B, C tips and from these equations, the tool life($\textrm{T}_{\textrm{L}}$) baced on the I.S.O. criteria was calculated to be $\textrm{T}_{\textrm{L}}$<$\textrm{T}_{\textrm{LB}}$<$\textrm{T}_{\textrm{LC}}$ for both flank wear($\textrm{V}_{\textrm{B}}$) and boundary wear($\textrm{V}_{\textrm{N}}$). Hence, the coated tips are superior to the uncoated tip and tip C is considered to be the best. 5. The cutting resistance may be slightly reduced and the surface rounghness improved when the damper is used especially when V>100 m/min. Therefore this damping device is considered to be effective and practical. The experimental surface roughness equations were also derived. Based on the vibration test, it is established that the surface roughness improvement was the result of amplitude reduction made possible by the damper.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.15 no.2
• /
• pp.13-23
• /
• 2016

Many traffic centers are highly hesitant in employing existing Automatic Incident Detection Algorithms due to high false alarm rate, low detection rate, and enormous effort taken in maintaining algorithm parameters, together with complex algorithm structure and filtering/smoothing process. Concerns grow over the situation particularly in Freeway Incident Management Area This study proposes a new algorithm and introduces a novel concept, the Displaced Flow Index (DiFI) which is similar to a product of relative speed and relative occupancy for every execution period. The algorithm structure is very simple, also easy to understand with minimum parameters, and could use raw data without any additional pre-processing. To evaluate the performance of the DiFI algorithm, validation test on the algorithm has been conducted using detector data taken from Naebu Expressway in Seoul and following transferability tests with Gyeongbu Expressway detector data. Performance test has utilized many indices such as DR, FAR, MTTD (Mean Time To Detect), CR (Classification Rate), CI (Composite Index) and PI (Performance Index). It was found that the DR is up to 100%, the MTTD is a little over 1.0 minutes, and the FAR is as low as 2.99%. This newly designed algorithm seems promising and outperformed SAO and most popular AIDAs such as APID and DELOS, and showed the best performance in every category.

• Korean Journal of Remote Sensing
• /
• v.14 no.1
• /
• pp.17-36
• /
• 1998

The Radon transform has been widely used in various techniques of digital image processing such as the computerized topography, lineament analysis in a remotely sensed image, slant-stack processing of seismic data, and so on. Compared to the Fourier transform, the utility of two-dimensional convolutional or correlational properties of the Radon transform, however, has been underestimated. We show that the two-dimensional convolution and correlation is respectively reduced to be one-dimensional convolution and correlation with respect to ρ in the Radon space. Therefore, one can achieve a two dimensional filtering by applying a simple one-dimensional convolution in the Radon space followed by an inverse Radon transform. Tests of the approach using FIR filters are carried out specifically for enhancing the ship wake in a RADARSAT SAR image. The test results demonstrate that the two-dimensional filtering through the Radon transform effectively enhance the ship wake features as well as reducing sea speckle in the image. Although two-dimensional convolution and correlation through the Radon transform are not so much useful as those through the courier transform in views of efficiency and effectiveness, it can be utilized to improve the quality of a digitally processed output when the process should be accompanied by the Radon transform such as topography and lineament analysis of SAR image.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.2
• /
• pp.732-740
• /
• 2019

Evaporative humidification using a humidifying element is widely used for humidification of a building or a data center. The performance of a humidifying element is commonly expressed as humidification efficiency, which is used independent of air temperature, humidity and water temperature. In this study, a series of tests were conducted at two air conditions (data center and commercial building) using two different humidifying elements (cellulose/PET and Glasdek) changing the frontal air velocity and water temperature. Results showed that the measured humidification efficiency was dependent on the air condition and water temperature. In fact, even dehumidification occurred at the inlet of the humidifying element at the air condition of commercial building. The reason was due to the inlet water temperature, which was lower than the dew point air temperature. As the difference between the inlet water and the dew point air temperature increased, the humidification efficiency decreased. This suggest that proper thermal model should account for the inlet region, where the amount of moisture transfer may be different from the other part of the humidification element. A simple analysis on the thermal performance of the cellulose/PET humidification element showed that the Sherwood number was adequately predicted, whereas the friction factor was ovepredicted, probably due to the simplification of the channel geometry and the neglection of the water film on the element surface.

• Publications of The Korean Astronomical Society
• /
• v.35 no.3
• /
• pp.29-41
• /
• 2020

Korea has numerous astronomical resources, such as observational records, star maps, and a wealth of literature, covering the period from the Three Kingdoms (54 BC - 932 AD) to the Joseon Dynasty (1392 - 1910 AD). The research activities related to these resources have been limited to those by individual researchers. It is now necessary to conduct research by efficiently and systematically collecting and managing Korean astronomical records using an accessible Web environment. The purpose of this study is to complete a system that enables researchers systematically to collect and verify a large number of historical records related to astronomical phenomena in a Web environment. In 2017, a preliminary survey was conducted, and the requirements pertaining to an implementation target system were devised. In addition, a joint development plan was carried out by the developer, lasting three months in 2018. Although the system is relatively simple, it is the first system to be attempted in the historical astronomy field. In order to proceed with the systematic development, the software development methodology is applied to the entire process from deriving the requirements of researchers to completing the system. The completed system is verified through integrated function and performance tests. The functional test is repeated while modifying and testing the system based on various test scenarios. The performance test uses a performance measurement test tool that takes measurements by setting up a virtual operation environment. The developed system is now in normal operation after a one-year trial period. Researchers who become authorized to use the system can use it to verify the accuracy of data and to suggest improvements. The collected feedback will be reflected in future systems, and Korean astronomical records will be available for use internationally through a multilingual service.