• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2011.05a
• /
• pp.131-132
• /
• 2011

This study analyzes the yearly-best delivered size range of truck mixer based on the specified mix, Water to Binder Ratio, aggregate proportion and unit amount with statistical method targeting on Kyeongi and Kyeongsang province and compares with the similar materials of Japan to propose as a basic standard for the quality control of mixer truck. As a result, in case of the Water to Binder Ratio of these areas, it is higher than Japan's due to the excessive safety rate reflecting the changes of differential value impact and unit amount, and the unit amount's standard deviation is very large by reflecting the changes of the amount used and chemical admixture susceptibility. In case of aggregate proportion, the frequency rate is about 50%, which is very similar value with Japan's one.

• IE interfaces
• /
• v.19 no.4
• /
• pp.342-354
• /
• 2006

The purpose of this thesis is to develop the schemes of supporting estimate for marine engines’ factories which are in a general make-to-order style. The marine engines’ factories currently use the method which depends on the past data and experiences handled by the responsible person, which causes inefficiency and inaccuracy in dealing with a huge amount of data. We apply association rule to solving the problems mentioned above. Critical data for analysis is filtered among materials that have been using actual records of performance so far. Secondly, relation with each part of marine engines through filtered data so that the company can estimate cost promptly and precisely if customers with similar components as requested. By proposed method of study estimate support efficient and supported exactly.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.19 no.3
• /
• pp.331-338
• /
• 2021

Extensive studies have been conducted on thermal conductivity of bentonite buffer materials, as it affects the safety performance of barriers engineered to contain high-level radioactive waste. Bentonite is composed of several minerals, and studies have shown that the difference in the thermal conductivity of bentonites is due to the variation in their mineral composition. However, the specific reasons contributing to the difference, especially with regard to the thermal conductivity of bentonites with similar mineral composition, have not been elucidated. Therefore, in this study, bentonites with significantly different thermal conductivities, but of similar mineral compositions, are investigated. Most bentonites contain more than 60% of montmorillonite. Therefore, it is believed that the exchangeable cations of montmorillonite could affect the thermal conductivity of bentonites. The effect of bentonite type was comparatively analyzed and was verified through the effective medium model for thermal conductivity. Our results show that Ca-type bentonites have a higher thermal conductivity than Na-type bentonites.

• KSBB Journal
• /
• v.23 no.4
• /
• pp.335-339
• /
• 2008

Biodiesel is an alternative and renewable energy source, which is hoped to reduce global dependence on petroleum and environmental problem. Biodiesel produced from a variety of oil sources such as vegetable oil, animal fat and waste oils, and has properties similar to those associated with petro-diesel, including cetane number, volumetric heating value, flash point, viscosity and so on. In this study, we investigate the effect of quality of raw materials on alkali-catalyzed transesterification for producing of biodiesel. The increase of content of free fatty acid and water in oil were caused the sharp decrease of conversion yield. Also, the low purity of methanol in reactant was inhibited the reaction rate. In the case of addition of sodium sulfate as absorbent to prepare catalyst solution, the content of fatty acid methyl ester in product was increased more about 1.6% than that of control. However, the addition of zeolite, sodium chloride and sodium sulfate as absorbent in reactant to remove water generated from reaction did not show any enhancement in the reaction yield. This result may provide useful information with regard to the choice and preparation of raw materials for more economic and efficient biodiesel production.

• Journal of Korea Foundry Society
• /
• v.11 no.4
• /
• pp.314-322
• /
• 1991

In this study, Na, Li, Sb, Sr were added as the modifiers to improve the mechanical proper ties of Al-Si alloys and their effects were compared one another Thermal analysis was carried out to measure the degree of undercooling, that is, the basic mechanism of modifying effect. The measurements of holding time and analyses of components of Al-Si alloys were carried out to compare the fading of the modifiers. Greater degree of undercooling was measured from the modified alloy than the normal alloys. In the modified alloy, the shape of Si was changed into a fine fiber phase or a lamellar phase from the coarse plate phase. There are not modifying effect of Sb below the $1.5^{\circ}C$ /sec of cooling rate. As the cooling rate increases, similar effects appears in the non-modified alloys like the modified alloys. Na and Li were faded in short time and were difficult to control on the melt, but Sb and Sr were scarcely faded for 6 hours of holding and were easy to control on the melt. Na and Sr are the good modifiers in terms of microstructure. Sb is the best modifier, but Na, Li are the inadequate modifiers in terms of fading.

• Tribology and Lubricants
• /
• v.23 no.6
• /
• pp.266-271
• /
• 2007

The brake performance of sintered friction materials for the high speed train was studied. In this study, newly developed sintered materials based on copper were compared with the commercial products for high speed trains. They were tested on a 1/5 scale dynamometer using low carbon steel disks. Effectiveness, fade, and recovery tests were carried out to examine friction performance and the change of disk thickness variation (DTV) during brake applications and noise propensity were also evaluated. Results showed that the two sintered friction materials exhibit similar friction coefficients and braking performance, whereas the newly developed friction material was superior in terms of DTV generation and noise propensity to the commercial friction material. The improvement of the newly developed friction material was attributed to the high graphite content which reduced the stick-slip phenomena and prevented uneven disk wear by producing friction films on the counter disk.

• Journal of Powder Materials
• /
• v.16 no.6
• /
• pp.416-423
• /
• 2009

Diamond/SiC composites are appropriate candidate materials for heat conduction as well as high temperature abrasive materials because they do not form liquid phase at high temperature. Diamond/SiC composite consists of diamond particles embedded in a SiC binding matrix. SiC is a hard material with strong covalent bonds having similar structure and thermal expansion with diamond. Interfacial reaction plays an important role in diamond/SiC composites. Diamond/SiC composites were fabricated by high temperature and high pressure (HPHT) sintering with different diamond content, single diamond particle size and bi-modal diamond particle size, and also the effects of composition of diamond and silicon on microstructure, mechanical properties and thermal properties of diamond/SiC composite were investigated. The critical factors influencing the dynamics of reaction between diamond and silicon, such as graphitization process and phase composition, were characterized. Key factor to enhance mechanical and thermal properties of diamond/SiC composites is to keep strong interfacial bonding at diamond/SiC composites and homogeneous dispersion of diamond particles in SiC matrix.

• Korean Journal of Agricultural Science
• /
• v.38 no.1
• /
• pp.115-120
• /
• 2011

20% of total energy use to sustain temperature of building inside. In this reasons, researchers effort to improve the thermal insulation capacity with new wall system. Using appropriate materials and consisting new wall system should considered in energy saving design. OSB(Oriented strand board), Larch lining board used to consist wall system. $2{\sim}6$ Larch lining board has tongue & groove shape for preventing moisture. Comparing with gypsum board and green timber lining board as interior sheathing material, temperature difference of Green timber wall system was bigger than temperature difference of gypsum board wall system. This aspects indicate that Green timber wall system was revealed higher thermal insulation property than gypsum board wall system. Gypsum board portion transfer heat easily because temperature difference gradient of gypsum board wall system was smaller than OSB wall system. Total temperature variation shape of G-4-S and G-6-S show similar model but, temperature variation shape in green timber wall portion assume a new aspect. The purpose of this study was that possibility of thermal insulation variation and new composition of wall system identify to improve thermal insulation performance. In the temperature case, this study shows possibility of improving thermal insulation performance. Humidity, sunshine and wind etc. should considered to determine building adiabatic properties.

• Carbon letters
• /
• v.24
• /
• pp.1-9
• /
• 2017

We studied the basic properties and fabrication of reduced graphene oxide (rGO) prepared using eco-friendly reduction agents in the graphene solution process. Hydrazine is generally used to reduce graphene oxide (GO), which results in polluting emissions as well as fixed nitrogen functional groups on different defects in the graphene sheets. To replace hydrazine, we developed eco-friendly reduction agents with similar or better reducing properties, and selected of them for further analysis. In this study, GO layers were produced from graphite flakes using a modified Hummer's method, and rGO layers were reduced using hydrazine hydrate, L-ascorbic acid, and gluconic acid. We measured the particle sizes and the dispersion stabilities in the rGO dispersed solvents for the three agents and analyzed the structural, electrical, and optical properties of the rGO films. The results showed that the degree of reduction was in the order L-ascorbic acid ${\geq}$ hydrazine > glucose. GO reduced using L-ascorbic acid had a sheet resistance of $121k{\Omega}/sq$, while that reduced using gluconic acid showed worse electrical properties than the other two reduction agents. Therefore, L-ascorbic acid is the most suitable eco-friendly reduction agent that can be substituted for hydrazine.

• Journal of Surface Science and Engineering
• /
• v.50 no.3
• /
• pp.164-169
• /
• 2017

Ni-Cr-X ternary interlayers were investigated to improve the adhesion of Cu/Ni-Cr/Polyimide flexible copper clad laminates. The ternary compounds are sputtered Ni-Cr-X films (where X is one of Nb, V, Mo, or Ti), and the effect of third elements on the adhesion was evaluated and investigated chemically and mechanically. The feel strength was higher in the order of Ni-Cr-Nb > Ni-Cr-V > Ni-Cr > Ni-Cr-Mo > Ni-Cr-Ti. Nb, which has a comparable standard electrode potential to Cr, increased the adhesion, while Ti, with a low standard electrode potential, degraded the adhesion. The Ni-Cr-Nb interlayer was amorphous, while Ni-Cr-Ti was partially crystalline. The similar morphology structure of the Ni-Cr-Nb interlayer with polyimide resulted in a better adhesion.