• 한국분말재료학회지
• /
• 제22권1호
• /
• pp.15-20
• /
• 2015

The composite of porous silicon (Si) and amorphous carbon (C) is prepared by pyrolysis of a nano-porous Si + pitch mixture. The nano-porous Si is prepared by mechanical milling of magnesium powder with silicon monoxide (SiO) followed by removal of MgO with hydrochloric acid (etching process). The Brunauer-Emmett-Teller (BET) surface area of porous Si ($64.52m^2g^{-1}$) is much higher than that before etching Si/MgO ($4.28m^2g^{-1}$) which indicates pores are formed in Si after the etching process. Cycling stability is examined for the nano-porous Si + C composite and the result is compared with the composite of nonporous Si + C. The capacity retention of the former composite is 59.6% after 50 charge/discharge cycles while the latter shows only 28.0%. The pores of Si formed after the etching process is believed to accommodate large volumetric change of Si during charging and discharging process.

• Korean Chemical Engineering Research
• /
• 제59권3호
• /
• pp.326-332
• /
• 2021

본 연구에서는 수열 합성법을 이용하여 나노 실리콘이 포함된 구형의 탄소 복합체를 합성하고, 석유계 피치로 코팅하여 제조된 음극 소재의 전기화학 특성을 조사하였다. 수크로스의 몰 농도를 변화시켜 수열합성한 후, 유기 용매로 THF를 사용하여 피치로 코팅된 음극 복합소재를 제조하였다. 제조된 음극 소재는 SEM, EDS, XRD 및 TGA를 사용하여 물리적 특성을 분석하였으며, 1.0 M LiPF₆ (EC : DMC : EMC = 1 : 1 : 1 vol%) 전해액에서 사이클, 율속, 순환전압전류 및 임피던스 테스트를 통해 리튬이차전지의 전기화학 성능을 조사하였다. 1.5 M의 수크로스와 피치를 사용하여 제조된 실리콘/탄소 소재는 구형 형태를 보였으며, 1756 mAh/g의 높은 초기 용량, 50 사이클 후 82 %의 용량 유지율 및 2 C/0.1 C에서 81%의 우수한 속도 특성을 확인할 수 있었다.

• 한국전산구조공학회논문집
• /
• 제32권5호
• /
• pp.297-304
• /
• 2019

본 논문에서는 접착영역 모델을 이용하여 2상 리튬이온 충전 시 실리콘 음극 전극의 균열진전 해석을 수행하였다. 리튬화 실리콘은 결정질 실리콘에 비해 부피가 약 3배 이상 크므로 리튬이온 충전 시 외각의 리튬화 실리콘에 매우 큰 압축력이 작용하여 압축항복이 발생한다. 리튬이온 충전 시 외각의 리튬화 실리콘은 압축항복 후에 내부의 결정질 실리콘이 리튬화 실리콘으로 상 변이하면서 발생하는 부피 팽창으로 인해 인장력이 작용한다. 이러한 인장력으로 인해 발생하는 균열진전을 접착영역 모델을 이용하여 모사하였다. 사용한 접착영역 모델은 PPR 포텐셜 기반 접착영역 모델로 하나의 포텐셜을 사용하여 복합모드에 대해서도 에너지 소산에 일관성을 지니고 있다. 유한요소 수치해석 모델로 2상 리튬이온 충전 시 모서리 균열진전을 모사한 결과가 실제 실험결과와 일치함을 확인하였고, 균열 팁에서의 최대 인장응력의 각도를 분석하여 실제 실험처럼 균열진전 방향이 회전할 것을 예측할 수 있었다.

• 한국재료학회지
• /
• 제22권1호
• /
• pp.8-15
• /
• 2012

Silicon-based thin film was prepared at room temperature by an electrochemical deposition method and a feasibility study was conducted for its use as an anode material in a rechargeable lithium battery. The growth of the electrodeposits was mainly concentrated on the surface defects of the Cu substrate while that growth was trivial on the defect-free surface region. Intentional formation of random defects on the substrate by chemical etching led to uniform formation of deposits throughout the surface. The morphology of the electrodeposits reflected first the roughened surface of the substrate, but it became flattened as the deposition time increased, due primarily to the concentration of reduction current on the convex region of the deposits. The electrodeposits proved to be amorphous and to contain chlorine and carbon, together with silicon, indicating that the electrolyte is captured in the deposits during the fabrication process. The silicon in the deposits readily reacted with lithium, but thick deposits resulted in significant reaction overvoltage. The charge efficiency of oxidation (lithiation) to reduction (delithiation) was higher in the relatively thick deposit. This abnormal behavior needs to clarified in view of the thickness dependence of the internal residual stress and the relaxation tendency of the reaction-induced stress due to the porous structure of the deposits and the deposit components other than silicon.

• 동력기계공학회지
• /
• 제17권1호
• /
• pp.110-115
• /
• 2013

The electrochemical performance and microstructure of Al-Si, Al-Si/C was investigated as anode for lithium ion battery. The Al-Si nano composite with 5 : 1 at% ratio was prepared by arc-discharge nano powder process. However, some of problem is occurred, when Al nano composite was synthesized by this manufacturing. The oxidation film is generated around Al-Si particles for passivating processing in the manufacture. The oxidation film interrupts electrical chemistry reaction during lithium ion insertion/extraction for charge and discharge. Because of the existence the oxidation film, Al-Si first cycle capacity is very lower than other examples. Therefore, carbon synthsized by glucose ($C_6H_{12}O_6$) was conducted to remove the oxidation film covered on the composite. The results showed that the first discharge cycle capacity of Al-Si/C is improved to 113mAh/g comparing with Al-Si (18.6mAh/g). Furthermore, XRD data and TEM images indicate that $Al_4C_3$ crystalline exist in Al-Si/C composite. In addition the Si-Al anode material, in which silicon is more contained was tested by same method as above, it was investigated to check the anode capacity and morphology properties in accordance with changing content of silicon, Si-Al anode has much higher initial discharge capacity(about 500mAh/g) than anode materials based on Aluminum as well as the morphology properties is also very different with the anode based Aluminum.

• 전기화학회지
• /
• 제21권1호
• /
• pp.12-20
• /
• 2018

To solve low cycle efficiency of the zinc anode in Zn-air batteries by corrosion, this study examined the effects of Al as a cathodic protection additive to Zn. The Al-mixed Zn anodes were produced by mixing Zn and Al powder (1, 2, and 3 wt. %). To compare the effects of the Al additive, Si was selected under the same conditions. The morphology and elemental composition of the additives in the Zn were characterized by scanning electron microscopy, energy dispersive X-ray spectroscopy, and inductively coupled plasma - mass spectrometry. The anti-corrosion effects of the Al and Si-mixed Zn anodes were examined by linear polarization. Cyclic voltammetry and charge-discharge tests were conducted to evaluate the electrochemical performance of the Al and Si-mixed Zn anodes. As a result, the Al-mixed Zn anodes showed highest corrosion resistance and cycling performance. Among these, the 2 wt.% Al-mixed Zn anodes exhibited best electrochemical performance.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 춘계학술대회 논문집
• /
• pp.461-464
• /
• 1999

This study has been investigated that traps generated inside of the oxide and at the oxide interfaces by the stress bias voltage. The traps are charged near the cathode with negative charge and charged near the anode with positive charge. The charge state of the traps can easily be changed by application of low voltages after the stress high voltage. These trap generation involve either electron impact ionization processes or high field generation processes. It determined to the relative traps locations inside the oxides ranges from 113.4$\AA$ to 814$\AA$ with capacitor areas of 10$^{-3}$ $\textrm{cm}^2$ . The oxide charge state of traps generated by the stress high voltage contain either a positive or a negative charge.

• 한국전기전자재료학회논문지
• /
• 제19권7호
• /
• pp.636-643
• /
• 2006

Si-C materials were synthesized by the heating the mixture of silicon and polyvinylidene fluoride (PVDF). The electrochemical properties of the Si-C materials as the high capacitive anode materials of lithium secondary batteries were evaluated by the galvanostatic charge-discharge test through 2032 type $Si-C{\mid}Li$ coin cells. Charge-discharge tests were performed at C/10 hour rate(C = 372 mAh/g). Initial discharge and charge capacities of $Si-C{\mid}Li$ cell using a Si-C material derived from PVDF(20wt.%) were found to be 1,830 and 526 mAh/g respectively. The initial discharge-charge characteristics of the developed Si-C electrode were analyzed by the electrochemical galvanostatic test adopting the capacity limited charge cut-off condition(GISOC). The range of reversible specific capacity IIE(intercalation efficiency at initial discharge-charge) and IICs(surface irreversible specific capacity) were 216 mAh/g, 68 % and 31 mAh/g, respectively.

• 한국표면공학회지
• /
• 제12권1호
• /
• pp.3-10
• /
• 1979

Many excellent Al-Zn-In anode have been developed up to the present. But for the purpose of the better performance of Al-Zn-In anodes in sea water the effect of calcium silicon addition on anodic polarization and current capacity of Al-Zn-In anodes was measured and analysed in sea water and artificial sea water. The results and conclusions obtained are summarized as follows. 1) Being compared with Al-Zn-In anodes, Al-Zn-In anodes containing 0.05% calcium silicon had superior characteristics in both anodic polarization and current capacity. 2) Corrosion patterns of the anodes containing calcium silicon were much more uniform than those of Al-Zn-In anodes. 3) In this experiment the most useful anode was Al-4% Zn-0.03% In-0.05% (Ca-Si). It had a capacity of 2.60Amp-hr of current/g and a voltage of 1.13(SCE reference) at anodic current density 1,000 4{\mu}A/cm^2$.

• Bulletin of the Korean Chemical Society
• /
• 제29권2호
• /
• pp.309-312
• /
• 2008

Two different anode composite materials comprising of Fe, Cu and Si prepared using high energy ball milling (HEBM) were explored for their capacity and cycling behaviors. Prepared powder composites in the ratio Cu:Fe:Si = 1:1:2.5 and 1:1:3.5 were characterized through X-Ray diffraction (XRD) and scanning electron microscope (SEM). Nevertheless, the XRD shows absence of any new alloy/compound formation upon ball milling, the elements present in Cu(1)Fe(1)Si(2.5)/Graphite composite along with insito generated Li2O demonstrate a superior anodic behavior and delivers a reversible capacity of 340 mAh/g with a high coulombic efficiency (98%). The higher silicon content Cu(1)Fe(1)Si(3.5) along with graphite could not sustain capacity with cycling possibly due to ineffective buffer action of the anode constituents.