• Elastomers and Composites
• /
• v.37 no.4
• /
• pp.258-264
• /
• 2002

In this work, the influence of thermal treatment on surface properties of silicas and mechanical interfacial properties of silicas/polyurethane composites was investigated. The surface properties of thermally treated silicas were studied in the context of Fourier Transform-IR (FT-IR), solid-state 29Si NMR spectroscopy, and contact angle. And the mechanical interfacial properties of the silica/polyurethane composites were evaluated by composite tearing energy (GIIIC). As a result, it was found that the thermally treated silica surfaces became hydrophobic in nature, due to the condensation of surface hydroxyls and the formation of siloxane bonds, resulting in increasing the London dispersive component of surface free energy. From which, the increase of the London dispersive component of the silicas led to an improvement of the dispersion of silicas in a polyurethane matrix, finally resulting in improving the tearing energy (GIIIC) of the silicas/polyurethane composites.

• Elastomers and Composites
• /
• v.51 no.2
• /
• pp.128-137
• /
• 2016

The effect of the surface area of silicas on their reinforcing performance to styrene-butadiene rubber (SBR) compounds was systematically investigated. The feasibility of the Brunauer-Emmett-Teller surface area ($S_{BET}$) as a parameter representing the characteristics of the silicas was discussed compared to the mesopore volume, c value, oil absorption, and uptake of silane. The increase in $S_{BET}$ of silicas caused a considerable increase in Mooney viscosity, minimum torque, and hysteresis loss of the silica-filled SBR compounds, while significantly enhancing their abrasion property. These changes were explained by the attrition between the hydrophilic silica surface and the hydrophobic rubber chains. As expected, the change in $S_{BET}$ did not induce any remarkable changes in the cure, processing, tensile, and dynamic properties of the silica-filled SBR compounds because the crosslinking density of the rubber chains mainly determined these properties.

• Analytical Science and Technology
• /
• v.8 no.3
• /
• pp.299-304
• /
• 1995

The adsorption behaviors of Ba(II), Cr(II), Fe(II) and Cu(II) on the N, N'-bispalmtoyl 1, 12-diaza-3, 4:9, 10-dibenzo-5, 8-cyclopentadecane (hexadecyl $NtnOenH_4$)-octadecylsilanized silicas(ODS) were investigated with water as the mobile phase. Binding constants for metal ions were measured in aqueous solution. The order of binding constants(K) and the degree of sorption(E) were Ba(II)$NtnOenH_4$-octadecyisiianized silicas(ODS) increased with concentration of metal ions, and the degree of adsorption was found to be affected by the cation-chelation mechanism. The experimental results showed good efficiency for separation of Cu(II) from mixtures of Ba(II), Cr(II), Fe(II) and Cu(II) in aqueous solution.

• Applied Chemistry for Engineering
• /
• v.25 no.5
• /
• pp.520-525
• /
• 2014

In this paper, the effect of silane-treated silicas and epoxidized soybean oil (ESBO) addition on adhesion properties of silicas-filled epoxy adhesives was examined. The silicas were treated by ${\gamma}$-methacryloxy propyltrimethoxy silane (MPS), ${\gamma}$-glycidoxy propyl trimethoxy silane (GPS), and ${\gamma}$-mercapto propyl trimethoxy silane (MCPS). Surface and structural properties of the adhesives were determined by using scanning electron microscope (SEM) and Fourier transform infrared spectroscopy (FT-IR). The t-peel strength of the adhesives was estimated using the universal testing machine (UTM). And, the equilibrium spreading pressure, surface free energy, and specific surface area were investigated by BET methods with $N_2$/77 K adsorption. As a result, the peel strength of the adhesives was increased in the presence of silane-treated silicas in the adhesives compared to that of untreated silicas. This result indicated that the silane coupling agent played an important role in improving the dispersion of silicas in epoxy adhesives. And, the adhesives treated by MCPS were superior to the others in adhesion.

• Macromolecular Research
• /
• v.10 no.4
• /
• pp.221-229
• /
• 2002

PET nanocomposites filled with fumed silicas were prepared via direct melt compounding method at various mixing conditions such as filler type and filler content. Some fumed silicas were pre-treated to improve the wettability and dispersibility, and principal characterizations were performed to investigate the effects of nano fumed silicas on polymer matrix. Hydrophobic fumed silica (M-FS), which has the similar contact angles of water with neat PET, acted as the best reinforcement for the thermal stability and mechanical properties of PET nanocomposite, and FE-SEM images also showed that M-FS was uniformly dispersed into matrix and had good wettability. But, some filler (O-FS) had low dispersibility and caused the deterioration of mechanical properties. Besides, the results of DSC revealed the nucleation effect of all fillers in polymer matrix, and PET nanocomposite filled with hydroptilic fumed silica (FS) showed markedly the characteristic dynamic rheological properties such as shear thinning behavior at very low frequencies and the decrease of viscosity.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.11
• /
• pp.3711-3718
• /
• 2012

Here, we report a chain-length dependent morphology and pore structure tailing of mesoporous silica templated from organogels, which is formed by primary alkylamine and ethylene glycol at room temperature. As the chain length of alkylamine changes from 12 to 18, the resulted materials exhibit a morphology change from layers to spheres and platelets, respectively. SEM and TEM observation revealed that these shapes appear to be inherited from their parent organogels. Further pore structure characterization by nitrogen sorption analysis demonstrates that all the resulted silicas exhibit typical IV isotherms indicative of uniform mesopores, and their pore sizes are dependent on the chain length of alkylamine used.

• Macromolecular Research
• /
• v.12 no.1
• /
• pp.85-93
• /
• 2004

We have prepared poly(ethylene terephthalate) (PET) nanocomposites filled with two different types of fumed silicas, hydrophilic (FS) and hydrophobic (MFS) silicas of 7-nm diameter, by in situ polymerization. We then investigated the morphological changes, rheological properties, crystallization behavior, and mechanical properties of the PET nanocomposites. Transmission electron microscopy (TEM) images indicate that the dispersibility of the fumed silica was improved effectively by in situ polymerization; in particular, MFS had better dispersibility than FS on the non-polar PET polymer. The crystallization behavior of the nanocomposites revealed a peculiar tendency: all the fillers acted as retarding agents for the crystallization of the PET nanocomposites. The incorporation of fumed silicas increased the intrinsic viscosities (IV) of the PET matrix, and the strong particleparticle interactions of the filler led to an increased melt viscosity. Additionally, the mechanical properties, toughness, and modules of the nano-composites all increased, even at low filler content.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2005.11b
• /
• pp.107-116
• /
• 2005

Precipitated silicas modified by aluminium were characterised using inverse liquid chromatography in anhydrous heptane with squalene as probes. Their monolayer capacities of adsorption, Langmuir's and Henry's constants were determined from the desorption isotherms according to frontal analysis. A narrow band consisting of isotherms was observed. The introduction of aluminium has little influence on the monolayer capacity, Langmuir's constants and the Henry constant. Experimental data show that neither the amounts of aluminium on the silica nor the methods of the introduction of aluminium into the silica influence the interactions between the squalene and the silicas.

• Journal of Korean Society of Water and Wastewater
• /
• v.21 no.1
• /
• pp.139-147
• /
• 2007

For environmental remediation of a contaminated groundwater plume, the use of zero-valent metal represents one of the latest innovative technologies. In this study, the effects of denitrification by zero-valent iron adsorbed in mesoporous silicas have been studied for groundwater contaminant degradation. The mesoporous silica was functionalized with 3-mercaptopropyltrimethoxysilane (MPTS) ligands and the zero-valent iron precipitated in the mesopore of granular silica was made by $FeCl_2$ and $NaBH_4$. Hydrogen was exchanged with $Fe^{2+}$ ions in the granular silicas. And then the ions were reduced by sodium borohydride in the mesoporous silicas. The surface area of the silica determined via the BET method ranged from 858 to $1275m^2/g$. The reductive reaction of nitrate-nitrogen indicated that the degradation of nitrate-nitrogen appeared to be pseudo first-order with the observed reaction rate constant kobs ($0.1619h^{-1}$) and to be directly proportional to the specific surface area. Therefore, the mesoporous silica with nano zero-valent iron proposed as a novel treatment strategy for contaminated groundwater was successfully implemented herein for the removal of nitrate-nitrogen.

• Clean Technology
• /
• v.17 no.1
• /
• pp.13-18
• /
• 2011

Phosphine ligand-grafted mesoporous silica materials with large pores were prepared for the ligand-modified heterogeneous Pd nanocatalysts. New heterogeneous catalytic system was developed using palladium nanoparticles encapsulated in phosphine ligand-grafted mesoporous silica. The catalyst showed good catalytic activities for Suzuki cross-coupling using bromobenzene derivatives due to excellent phosphine ligand effects. Catalytic results showed nanoparticie catalysts can be recycled twice with decreased yields.