• JSTS:Journal of Semiconductor Technology and Science
• /
• 제12권3호
• /
• pp.270-277
• /
• 2012

This paper presents a new DAC design strategy to achieve a wideband dynamic linearity by increasing the bandwidth of the output impedance. In order to reduce the dominant parasitic capacitance of the conventional matrix structure, all the cells associated with a unit current source and its control are stacked in a single column very closely (stacked unit cell structure). To further reduce the parasitic capacitance, the size of the unit current source is considerably reduced at the sacrifice of matching yield. The degraded matching of the current sources is compensated for by a self-calibration. A prototype 6-bit 3.3-GS/s current-steering full binary DAC was fabricated in a 1P9M 90 nm CMOS process. The DAC shows an SFDR of 36.4 dB at 3.3 GS/s Nyquist input signal. The active area of the DAC occupies only $0.0546mm^2$ (0.21 mm ${\times}$ 0.26 mm).

• Journal of information and communication convergence engineering
• /
• 제9권4호
• /
• pp.435-440
• /
• 2011

This paper propose the method of constructing the highly efficiency adder and multiplier systems over finite fields. The addition arithmetic operation over finite field is simple comparatively because that addition arithmetic operation is analyzed by each digit modP summation independently. But in case of multiplication arithmetic operation, we generate maximum k=2m-2 degree of ${\alpha}^k$ terms, therefore we decrease k into m-1 degree using irreducible primitive polynomial. We propose two method of control signal generation for the purpose of performing above decrease process. One method is the combinational logic expression and the other method is universal signal generation. The proposed method of constructing the highly adder/multiplier systems is as following. First of all, we obtain algorithms for addition and multiplication arithmetic operation based on the mathematical properties over finite fields, next we construct basic cell of A-cell and M-cell using T-gate and modP cyclic gate. Finally we construct adder module and multiplier module over finite fields after synthesizing ${\alpha}^k$ generation module and control signal CSt generation module with A-cell and M-cell. Next, we constructing the arithmetic operation unit over finite fields. Then, we propose the future research and prospects.

• 전기전자학회논문지
• /
• 제18권2호
• /
• pp.282-290
• /
• 2014

본 논문은 1인승 전기차량의 임베디드 전동 제어장치 설계를 제안하였다. 제안된 임베디드 장치는 PIC18F8720 프로세서, 16Mb flash ROM, 32Mb SDRAM과 신호처리회로로 설계되었다. 제안된 1인승 전기차량은 4KW 인휠 BLDCM, $180^{\circ}$ 도통 공간 벡터제어 3상 전압형 인버터, PID 속도제어기와 전동제어 장치와 임베디드 제어장치로 구성된다. 이 1인승 전기차량은 역 3륜 형태의 기계적인 구조를 가지고 있으며, 인휠 BLDCM과 틸팅 기능을 가지는 조향 메카니즘이 적용되었다. 또한 제안된 임베디드 전동제어장치의 성능은 PEV에 대한 Lab 실험과 도로 주행시험을 통하여 검증하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 합동 추계학술대회 논문집 정보 및 제어부문
• /
• pp.114-117
• /
• 2002

The airborne tracking radar is located in front of aircraft or missile and measures and tracks a target motion. The signal processor receives target signals from a receiver using A/D converters, and calculates the target motion, and transfers the data to the aircraft or missile control unit. Since the signal processing system is required to be lightweight and small size as well as high performance to calculate and analyze the received signal, we use high speed DSPs and SMD type components having low power consumption. In this paper, we describe the design concept of signal processing system of the airborne tracking radar.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.572-578
• /
• 2008

As the railway transportation is getting faster and its operation speed has increased rapidly, its signal control has been complicated. For real time signal processing it is very important to prohibit any critical error from causing the system to malfunction. Therefore, handling complicated signals effectively while maintaining fault-tolerance capability is highly expected in modern railway transportation industry. In this paper, we suggest an SoC (Sytem-on-Chip) design method to integrate these complicated signal controlling mechanism with fault tolerant capability in a single chip. We propose an SoC solution which contains a high performance 32-bit embedded processor, digital filters and a PWM unit inside a single chip to implement ATO's, ATC's, ATP's and ATS's digital signal-processing units. We achieve an enhanced reliability against the calculation error by adding fault tolerance features to ensure the stability of each module.

• International Journal of Precision Engineering and Manufacturing
• /
• 제5권2호
• /
• pp.46-52
• /
• 2004

Numerous connectors are used in automobiles for transmission of electrical signals across various electro-mechanical components. The connectors must operate with high reliability in order to minimize failures due to signal degradation. In this work, the effects of contamination at the contact interface of connectors used fur automobile crankshaft position sensor on the impedance change were investigated. An experimental set-up was built to simulate the electrical signal transmitted from the sensor to the engine control unit through a connector. Output from the connector was investigated using connectors contaminated with engine block residues and water droplets. It was found that slight contamination of the connectors could lead to significant signal degradation which can lead to engine failure. Also, the effect of water in the connector altered the signal severely. However, the signal gradually regained the original state as the water evaporated from the interface.

• 대한의용생체공학회:의공학회지
• /
• 제22권3호
• /
• pp.249-257
• /
• 2001

본 논물에서는 척수 손상으로 인하여 암이 수축 및 이완시 미약한 근전도, 신호를 발생시키는 환자로부터 명확한 수축 및 이완 패턴을 추출하기 위한 신호 처리 기법을 제안하였다. 제안한 방법은 비선형 고정 필터의 일종인 FatBear 필터를 이용하여 거대 운동단위 활동전위로 의심되는 충격 잡음을 제거하고 웨이브렛 평면에서 비선형 멀티 스케일 필터링 기법을 이용하여 가산 잡음을 제거하는 것으로서 횡단성 척수염으로 인한 마미 증후근을 보이는 환자들에게 적용하여 명확한 수축 및 이완 패턴을 추출할 수 있었다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.49-52
• /
• 2003

Two types of ozone monitors using UV absorption method were tried in consideration of cost of the monitor and precision in measuring. The high concentration ozone monitor for high concentration real time ozone monitoring from ozone generator was composed of a low pressure mercury lamp as UV source, a photo multiplier tube as UV detector and signal processing unit for the most part. This structure could be very useful for low price high concentration ozone monitor due to simple system structure and fairly good monitoring characteristics. The developed system showed good linear output characteristics to ozone in the measuring concentration range of 0.05 and 2 wt.%. For accuracy ambient ozone monitoring in ambient in ppm level, the system composed of a high power pulsed xenon lamp as UV source, an optical spectrometer with a high sensitivity linear CCD array as UV detector and signal processing unit in brief speaking was proposed our study for the first time in the world. The developed system showed good linearity and sensitivity in relative low measuring range between 10ppm and 10,000ppm, and showed some feasibility of high resolution ozone monitor using CCD array as photodetector.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2000년도 추계학술대회 논문집
• /
• pp.222-227
• /
• 2000

"Side scan sonar" using acoustic signal has been developed to survey cable laying, sunken bodie\ulcorner bottom and so on. It use the acoustic signals, which are emitted from two transducer arrays, to get gemetri\ulcorner target area. This system consists of transceiver board, towed body, and deck unit. The transceiver board, w\ulcorner watertight canister of the towed body, controls the transmitting and receiving of 400kHz acoustic signals from \ulcorner After receiving the scattered signals, it processes the filtering, AGF(Automatic Gain Control), TVG(Time Heterodyne. The deck unit is composed of the signal processing part, A/D converter, power supplier, and real\ulcorner And the towed body has been designed to satisfy the optimal hydrodynamic behavior during towing. The de\ulcorner theory of transceiving part and some results from field-experiments will be introduced here.

• Journal of information and communication convergence engineering
• /
• 제5권4호
• /
• pp.362-368
• /
• 2007

A single-phase uninterruptible power supply system equipped with a superconducting magnet energy storage unit is proposed to achieve a simple circuit configuration and higher system reliability. It reduces a number of switching devices by applying a common-arm scheme. Removing some switches or substituting passive elements for active switches can increase the sophistication and reduces degree of freedom in control strategy. However, high-performance DSP controller can execute the complicated control task with no additional cost. Operational principles to normal, stored-energy, and bypass mode are discussed in detail. The validity of the proposed system is verified by experimental results.