• Tribology and Lubricants
• /
• v.23 no.3
• /
• pp.109-116
• /
• 2007

A scroll compressor is on the increase in the use for the cooling and ambition machinery because of the advantages about high efficiency, low vibration and low noise. The design of thrust bearing for scroll compressor has depended on the experience. The lubrication considering the squeeze flow was applied for high side shell and low side shell of scroll thrust bearing. This work was based on governing fluid lubrication equation at the general coordinate. It shows the behavior for an orbiting scroll with direct numerical analysis using FDM. This study obtained the theoretical design value by finding load capacity and tilting angle of an orbiting scroll for thrust bearing in a scroll compressor. Especially this work performed the analysis about the design parameter. The program was written using Visual C++ to enhance user to change the design parameter easily. In particular the result value and the pressure profile were displayed as windows in every step for user to understand without difficulty.

• 한국전산유체공학회:학술대회논문집
• /
• 2000.05a
• /
• pp.172-177
• /
• 2000

In this numerical work, three dimensional supersonic laminar flow and heat transfer of a blunt body(sphere-cone) at Mach 5 is simulated. The effects of angle of attack and the spin rate on the now and heat transfer are analysed. To solve the three dimensional compressible Wavier-Stokes equation, a finite volume method with the modified LDFSS scheme is employed for spatial discretization, and a point SGS implicit method is used for time integration. It is found that the heat transfer rate increases at the windward side and decreases at the leeward side with the angle of attack. The heat transfer rate at all surfaces slightly increases with the spin rate.

• Journal of Photoscience
• /
• v.1 no.1
• /
• pp.69-73
• /
• 1994

Sporangiophores (spphs) of Phycomyces blakesleeanus are positively phototropic to unilateral visible (blue) light over a range of fluence rates 10$^{-9}$ to 1 W/m$^2$. The maximal bending angle is always 70-75$\circ$ from the vertical. Many mutants with abnormal phototropism have been isolated. Complementation tests revealed that the genetic grouping is completely consistent with the phenotypic classification scheme, based on sensory responses other than those to light. The spph of the piloboloid mutant, the growth zone of which gradually ceases elongation but expands spherically, and the $\beta$-carotene-overproducing mutant show negative phototropism, in contrast to the wild type spph. We hypothesized that the phototropic orientation of spph is determined by the ratio of the maximal light fluenee rate at the proximal side to that at the distal side of the spph. Based on this hypothesis, we found that the maximal bending angle was larger in thin spphs than in thick ones, and larger in spphs containing smaller amount of $\beta$-carotene than in carotene-rich spphs. In addition to our hypothesis, gravitropic experiments revealed that the maximal bending angle of the wild type spph results from a balance among positive phototropism, negative gravitropism, and the optical properties of the spph. For further advancement of this study, we developed a mutant with a high proportion of uninucleate spores, and designed an efficient microinjection method for obtaining transformants.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.8
• /
• pp.703-710
• /
• 2004

This paper presents discontinuous zigzag gait analysis for a newly modeled quadruped walking robot with an articulated spine which connects the front and rear parts of the body. An articulated spine walking robot can move easily from side to side, which is an important feature to guarantee a larger gait stability margin than that of a conventional single rigid-body walking robot. First, we suggest a kinematic modeling of an articulated spine robot which has new parameters such as a waist-joint angle, a rotate angle of a front and rear body and describe characteristics of gait using an articulated spine. Next, we compared the difference of walking motion of newly modeled robot with that of a single rigid-body robot and analyzed the gait of an articulated spine robot using new parameters. On the basis of above result, we proposed a best walking motion with maximum stability margin. To show the effectiveness of proposed gait planning by simulation, firstly the fastest walking motion is identified based on the maximum stride, because the longer the stride, the faster the walking speed. Next, the gait stability margin variation of an articulated spine robot is compared according to the allowable waist-joint angle.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.288-293
• /
• 2000

BPM simulation was used in order to fabricate the LiNbO$_3$optical waveguide with optical source of He-Ne laser(λ=0.6328[$\mu$m]). we observed electric field E$_{x}$, E$_{y}$ in the x,y-direction are simulated at the LiNbO$_3$substrate (X1 55[$\mu$m]$\times$Z1 5000[$\mu$m]), where the depth, width and buffer layer of waveguide are 0.2[$\mu$m],4[$\mu$m] and 0.02[$\mu$m] respectively. By applying these parameters of single waveguide to simulate a X-switch, we have chosen index change of 0.002, width of 3[$\mu$m] and angle of 0.4$^{\circ}$~0.6$^{\circ}$of optical waveguide and under these conditions, optical beam propagates cross-side at 0.4$^{\circ}$. When applied switching voltage of 25[V], optical beam of X-switch turns cross-side to bar-side at intersection angle 0.4$^{\circ}$, index change of 0.002, waveguide width of 3[$\mu$m], electrode gap 2[$\mu$m]. By the above results, we can obtain design conditions of theoretical analysis of an X-switch optical waveguide.e.e.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.15 no.3 s.39
• /
• pp.229-238
• /
• 1991

The object of this study is to develope an improved version of brassiere with better fit and improved performance by conducting a try-on test on 6 types of revised brassieres (constructed on above basis). The study procedures consisted of a try-on test of experimentally constructed brassieres and a sensory test on fit. The results of experimentally constructed brassiere trial are as follows. 1. The sizes showing performance effects due to different types of experimentally construct- ed brassieres were bust length, bust height, under bust curve length, vertical and horizontal bust diamenter, upper-lower bust slope angle (direct measurement, parallel standard, upper torso tilt rate), side bust slope angle and top bust slope angle. 2. Concerning the changes in lower cup interior, elastic materials and wider portions perfor-med better in bust up effect. 3. No effects due to different shoulder strap positions were observed, but combined with lower cup interior changes the side types proved more effective than the standard types.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.9
• /
• pp.892-896
• /
• 2011

This paper describes a camera-based position measurement system for automatic tracking control of a rubber Tired Gantry Crane (RTGC). An automatic tracking control of RTGC depends on the ability to measure its displacement and angle from a guide line that the RTGC has to follow. The measurement system proposed in this paper is composed of a camera and a PC that are mounted on the right upper between front and rear tires of the RTGC's side. The measurement accuracy of the system is affected by disturbances such as cracks and stains of the guide line, shadows, and halation from the light fluctuation. To overcome the disturbances, both side edges of the guide line are detected as two straight lines from an input image taken by the camera, and parameters of the straight lines are determined by using Hough transform. The displacement and angle of the RTGC from the guide line can be obtained from these parameters with the robustness against the disturbances. From the experiments with the disturbances, we found the accurate displacement and the angle from the guide line that have the standard deviations of 0.95 pixels and 0.22 degrees, respectively.

• Journal of the Korean Ceramic Society
• /
• v.56 no.4
• /
• pp.354-359
• /
• 2019

Information security films that can ensure personal privacy by reducing the viewing angle of display screens were fabricated by microlouver patterning and a ZnO nano-ink filling process. Optical simulation results demonstrated that all the microlouver films showed good security performances. Security performances were evaluated as calculated relative luminance ratios compared between the side and front. Based on the simulation results, microlouver films were fabricated by UV imprint lithography and nano-ink bar coating. However, distortion of the microlouver pattern occurred with the use of high-viscosity nano-inks such as ZrO₂ and TiO₂, and the CuO-filled microlouver film suffered from very low optical transmittance. Accordingly, the effects of ZnO filling height on security performance were intensively investigated through simulation and experimental measurements. The fabricated microlouver film with a 75-㎛-high ZnO filling exhibited a good relative luminance ratio of 0.75 at a 60° side angle and a transmittance of 44% at a wavelength of 550 nm.

• The Academic Congress of Korean Shoulder and Elbow Society
• /
• 2008.03a
• /
• pp.179-179
• /
• 2008

For a partial tear of the subscapularis tendon, the presenting technique requires only the anterior portal for preparing the footprint and suture management, as well as the subclavian portal for placing the suture anchor and suture hook without inserting a cannula. It provides both a good angle for anchor placement and sufficient space for managing the upper portion of a subscapularis tendon tear. A spinal needle was inserted through the subclavian portal in order to identify the appropriate angle for placing the suture anchor. A 3-mm incision was made for the subclavian portal and a biosuture anchor was placed on the footprint portion of the subscapularis tendon. In order to avoid crowding, each limb of both strands of the biosuture anchor were passed through the tendon- posteromedial side first, and anterolateral side second, using a switching technique with suture hook embedded with no.1 PDS. A suture tie was applied in a reverse sequence (the lateral strand first and the medial strand second) through the anterior cannula using a sliding technique.

• Structural Engineering and Mechanics
• /
• v.54 no.1
• /
• pp.35-54
• /
• 2015

The performance of a newly generated steel connection known as SidePlateTM moment connection for seismic loading and progressive collapse phenomenon has been investigated in this paper. The seismic evaluation portion of the study included a thorough study on of interstory drift angles and flexural strengths based on 2010 AISC Seismic Provisions while the acceptance criteria provided in UFC 4-023-03 guideline to resist progressive collapse must be satisfied by the rotational capacity of the connections. The results showed that the SidePlate moment connection was capable of attaining adequate rotational capacity and developing full inelastic capacity of the connecting beam. Moreover, the proposed connection demonstrated an exceptional performance for keeping away the plastic hinges from the connection and exceeding interstory drift angle of 0.06 rad with no fracture developments in beam flange groove-welded joints. The test results indicated that this type of connection had strength, stiffness and ductility to be categorized as a rigid, full-strength and ductile connection.