• Journal of Power Electronics
• /
• v.15 no.1
• /
• pp.190-201
• /
• 2015

This paper uses the switching function approach to present a simple state model of the Vienna-type rectifier. The approach introduces the relationship between the DC-link neutral point voltage and the AC side phase currents. A novel direct power control (DPC) strategy, which is based on the sliding mode control (SMC) for Vienna I rectifiers, is developed using the proposed power model in the stationary ${\alpha}-{\beta}$ reference frames. The SMC-based DPC methodology directly regulates instantaneous active and reactive powers without transforming to a synchronous rotating coordinate reference frame or a tracking phase angle of grid voltage. Moreover, the required rectifier control voltages are directly calculated by utilizing the non-linear SMC scheme. Theoretically, active and reactive power flows are controlled without ripple or cross coupling. Furthermore, the fixed-switching frequency is obtained by employing the simplified space vector modulation (SVM). SVM solves the complicated designing problem of the AC harmonic filter. The simplified SVM is based on the simplification of the space vector diagram of a three-level converter into that of a two-level converter. The dwelling time calculation and switching sequence selection are easily implemented like those in the conventional two-level rectifier. Replacing the current control loops with power control loops simplifies the system design and enhances the transient performance. The simulation models in MATLAB/Simulink and the digital signal processor-controlled 1.5 kW Vienna-type rectifier are used to verify the fast responses and robustness of the proposed control scheme.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.39 no.4
• /
• pp.90-96
• /
• 2016

Incremental sheet forming (ISF) is a highly versatile and flexible process for rapid manufacturing of complex sheet metal parts. Compared to conventional sheet forming processes, ISF is of a clear advantage in manufacturing small batch or customized parts. ISF needs die-less machine alone, while conventional sheet forming requires highly expensive facilities like dies, molds, and presses. This equipment takes long time to get preparation for manufacturing. However, ISF does not need the full facilities nor much cost and time. Because of the facts, ISF is continuously being used for small batch or prototyping manufacturing in current industries. However, spring-back induced in the process of incremental forming becomes a critical drawback on precision manufacturing. Since sheet metal, being a raw material for ISF, has property to resilience, spring-back would come in the case. It is the research objective to investigate how geometrical shaping parameters make effect on shape dimensional errors. In order to analyze the spring-back occurred in the process, this study experimented on Al 1015 material in the ISF. The statistical tool employed experimental design with factors. The table of orthogonal arrays of $L_8(2^7)$ are used to design the experiments and ANOVA method are employed to statistically analyze the collected data. The results of the analysis from this study shows that the type of shape and the slope of bottom are the significant, whereas the shape size, the shape height, and the side angle are not significant factors on dimensional errors. More error incurred on the pyramid than on the circular type in the experiments. The sloped bottom showed higher errors than the flat one.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.7
• /
• pp.71-79
• /
• 2002

A new rapid prototyping process, Variable Lamination Manufacturing using a 4-axis-controlled hotwire cutter and expandable polystyrene foam sheet as a laminating material of the part (VLM-S), has been developed to reduce building time and to improve the surface finish of parts. The objective of this study is to reconstruct the surface of the original 3D CAD model in order to generate mid-slice data using the advancing front technique. The generation of 3D layers by a 4 axis-controlled hot-wire cutter requires a completely different procedure to generate toolpath data unlike the conventional RP CAD systems. The cutting path data for VLM-S are created by VLM-Slicer, which is a special CAD/CAM software with automatic generation of 3D toolpath. For the conventional sheet type system like LOM, the STL file would be sliced into 2D data only. However, because of using the thick layers and a sloping edge with the firstorder approximation between the top and bottom layers, VLM-Slicer requires surface reconstruction, mid-slice, and the toolpath data generation as well as 2D slicing. Surface reconstruction demands the connection between the two neighboring cross-sectional contours using the triangular facets. VLM-S employs thick layers with finite thickness, so that surface reconstruction is necessary to obtain a sloping angle of a side surface and the point data at a half of the sheet thickness. In the process of the toolpath data generation the surface reconstruction algorithm is expected to minimize the error between the ruled surface and the original parts..

• Structural Engineering and Mechanics
• /
• v.49 no.6
• /
• pp.705-726
• /
• 2014

In general, cylindrically curved plates are used in ships and offshore structures such as wind towers, spa structures, fore and aft side shell plating, and bilge circle parts in merchant vessels. In a number of studies, it has been shown that curvature increases the buckling strength of a plate under compressive loading, and the ultimate load-carrying capacity is also expected to increase. In the present paper, a series of elastic and elastoplastic large deflection analyses were performed using the commercial finite element analysis program (MSC.NASTRAN/PATRAN) in order to clarify and examine the fundamental buckling and collapse behaviors of curved plates subjected to combined axial compression and lateral pressure. On the basis of the numerical results, the effects of curvature, the magnitude of the initial deflection, the slenderness ratio, and the aspect ratio on the characteristics of the buckling and collapse behavior of the curved plates are discussed. On the basis of the calculated results, the design formula was developed to predict the buckling and ultimate strengths of curved plates subjected to combined loads in an analytical manner. The buckling strength behaviors were simulated by performing elastic large deflection analyses. The newly developed formulations were applied in order to perform verification analyses for the curved plates by comparing the numerical results, and then, the usefulness of the proposed method was demonstrated.

• Membrane and Water Treatment
• /
• v.8 no.2
• /
• pp.113-123
• /
• 2017

This study investigated effects of physical and chemical cleaning methods on the initial flux recovery of fouled membrane in membrane distillation process. A laboratory scale direct contact membrane distillation (DCMD) experiment was performed to treat digested livestock wastewater with 3.89 mg/L suspended solids, 874.7 mg/L COD, 543.7 mg/L nitrogen, 15.6 mg/L total phosphorus, and pH of 8.6. A hydrophobic PVDF membrane with an average pore size of $0.22{\mu}m$ and a porosity of 75 % was installed inside a direct contact type membrane distillation module. The temperature difference between feed and permeate side was maintained at $40^{\circ}C$ with the feed and permeate stream velocity of 0.18 m/s. The results showed that the permeate flux decreased from $22.1L{\cdot}m^{-2}{\cdot}hr^{-1}$ to $19.0L{\cdot}m^{-2}{\cdot}hr^{-1}$ after 75 hours of distillation. The fouled membrane was cleaned first by physical flushing and consecutively by chemicals with NaOCl and citric acid. After the physical cleaning the flux was recovered to 92 % as compared with the initial clean water flux of the virgin membrane. Then 94 % of the flux was recovered after cleaning by 2,000 ppm NaOCl for 90 minutes and finally 97 % of flux recovered after 3 % citric acid for 90 minutes. SEM-EDS and FT-IR analysis results presented that the foulants on the membrane surface were removed effectively after each cleaning step. The contact angle measurement showed that the hydrophobicity of the membrane surface was also restored gradually after each cleaning step to reach nearly the same hydrophobicity level as the virgin membrane.

• The Research Journal of the Costume Culture
• /
• v.25 no.2
• /
• pp.175-191
• /
• 2017

The purpose of this study is to analyze the body mass index(BMI) and foot characteristics of senior-generation women and to use those values to develop a standard shoe last for producing shoes that best fit the foot of senior-generation women. In order to develop a standard shoe last that reflects the BMI and foot characteristics of senior-generation women, I analyzed the morphometric characteristics of feet by conducting descriptive statistics for each item. The foot characteristics based on BMI were analyzed by conducting ANOVA and Duncan's tests via the foot's measured values. Subsequently, I developed a standard shoe last reflecting the BMI and the foot characteristics of senior-generation women by applying all those values. Senior-generation women showed significant differences among three groups based on BMI-normal weight, overweight, and obese-in all the items except for medial ball width and toe 5 angle. Through these values, I realized that as the value of the BMI becomes higher, the size of the foot becomes larger. This suggests that as a woman's weight increases or decreases, her shoes need to be replaced as well as her clothes. Deviations in the toe-side parts of the shoe could cause deformation of the foot. If someone keeps wearing shoes produced using a shoe last with a large deviation, she risks developing foot conditions like hallux valgus. This situation points to the need for shoe manufacture that utilizes a standard shoe last that reflects the BMI and foot characteristics of the senior generation.

• Advances in pediatric surgery
• /
• v.1 no.2
• /
• pp.133-139
• /
• 1995

Because rectal prolapse in pediatric age was known to have a self-limitting natural history in weeks to years, this disease is prone to be regarded as a minor condition to the most of surgeons. But to the children and the parents who have to be suffered each time could be a heavy distress. Even though operative or nonoperative methods can be applicable for treatment, the main problem is in surgeon's side, whose preference is based on the experiences of adult patients. The authors have experienced 16 cases of ano-rectal prolapse for 9 years since 1986. Eleven of them were true rectal prolapses. In 7 cases of true type, injection therapy has been tried. One ml of five percent phenol in glycerine was injected into the submucosal layer of the ano-rectal angle level at both lateral and posterior sides. After first trial of each cases, 5 of them were cured completely so far. Recurrences were in two cases, but one of them was temporary to be subsided afterward. Complete bowel cleansing and adequate sedations were required as preoperative preparations. Two days' oral antibiotics and two weeks' laxatives for free of defecation straining were recommended after the procedure. The safety of sclerosis was supported by the experimental histology. In pediatric rectal prolapse, sclerosis seems to be a safe and effective treatment of choice without any significant morbidity.

• Journal of Navigation and Port Research
• /
• v.36 no.1
• /
• pp.15-20
• /
• 2012

In order to investigate the maneuverability of tug-barge, sea trial tests such as speed, acceleration/deceleration, $10^{\circ}$ turning, $20^{\circ}$ turning, $10^{\circ}/10^{\circ}$ zigzag and $20^{\circ}/20^{\circ}$ zigzag were conducted with both tug and tug-barge. From the result of turning test, longer tactical diameter and lower rate of turn of tug-barge than those of tug are obtained. From the result of the zigzag test, bigger overshoot angle of tug-barge than that of tug is obtained. When they turned or changed a course, it showed that the barge turned inner side of the trajectory of tug. For the safe navigation, the helmsman of tug-barge should be aware of these maneuvering characteristics.

• Economic and Environmental Geology
• /
• v.2 no.3
• /
• pp.58-67
• /
• 1969

Songgwang lead zinc mine is located in about 12km to the north-east of Jeonju City. Geology of the mine and its visinity is consisted of Jeonju series belonged to so-called Okcheon system, Seodaesan tuff formation, Silla series, and the quartz porphyry intruded into these formations. Jeonju series comprising 3 formations; that is, of Sadaeri, Sindong, and Girinbong. Jeonju series is generally distributed in southern part of the area, striking NNW, and diping NE $30^{\circ}$, or NW $30^{\circ}$. It is deformed to form synclinorium and anticlinorium plunging to the north with low angle. In the northern part of the area, Jeonju series was cut by Sinpeongri-fault of NEE direction near Sinpeongri. In the north side of the fault, it is overturned and shows NEE or NWW strikes and NW $60^{\circ}$ dips. At the west of Songgwangri, it is cut by 3 thrusts; the two are almost parallel each other, and the third oneis manifested by the fact that the lower black shale zone thrusted over the upper limestone. Songgwangri thrust, so named, is a post-mineral fault and its plane represents a premineral slip plane. Enrichment of are took place along the bedding plane or fissure parallel to it, as seen in adit No. 1 or No. 2 along the floor of the thrust, and along the sheared zone or the brecciated zone oblique to the plane near the thrust in crystalline limestone of Sindong formation as observed in the underground levels of inclined slope. Ore minerals are chiefly zincblende, galena, pyrrhotite, arsenopyrite, acompanied pyrite and chalcopyrite, and contain Au and Ag. In earlier stage of mineralization, the limestone was recrystalized, and sulphide minerals were enriched in the· permiable zone said above by pyrometasomatism, and in later stage the limestone was affected chloritization and sericitization. However hydrothermal replacement was weak, so that enrichment did not took place. It seems that minerallizing materials came up through the premineral slip plane and injected, and replaced the limestone in permiable zone said above with sulphide are minerals. Then Songgwangri thrust took place and, the lower black shale zone thrusted upon crystalline limestone.

• Korean Journal of Applied Biomechanics
• /
• v.20 no.1
• /
• pp.83-90
• /
• 2010

The purpose of this study is to validate that change of impact by the Early Extension in during a golf driver swing. 13 golf players who were diagnosed with symptoms of Early Extension participated in a proactive corrective training programs that took place 3 times a week for a 4 month period. Data was collected by recording 5 pre and 5 post training driver swings and analyzing the data to calculate the change in velocity and its effect in the shot used the TRACK MAN. After the training, the changes of early extension were -0.21 cm in backswing section E2(take away), -0.64 cm in E3(halfway backswing), and -0.94 cm in E4(backswing top). The downswing section changes were -1.34 cm in event E5(halfway downswing), -1.74 cm in E6(impact). Impact force increased and thus club speed increased by 6.32 km/h, ball speed increased by 10.94 km/h, max height decreased by -6.22 m, carry increased by 10.85 m, carry side(left deviation) decreased by 4.84 m, flight time by increased by 0.4 sec, and total length increased by 17.96 m while landing angle decreased by -7.74 deg.