• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.3A
• /
• pp.201-209
• /
• 2010

Generally, PSC girder bridge uses total gross cross section to resist applied loads unlike reinforced concrete member. Also, it is used as short and middle span (less than 30 m) bridges due to advantages such as ease of design and construction, reduction of cost, and convenience of maintenance. But, due to recent increased public interests for environmental friendly and appearance appealing bridges all over the world, the demands for longer span bridges have been continuously increasing. This trend is shown not only in ordinary long span bridge types such as cable supported bridges but also in PSC girder bridges. In order to meet the increasing demands for new type of long span bridges, PSC hollow box girder with H-type steel as compression reinforcements is developed for bridge with a single span of more than 50 m. The developed PSC girder applies compressive prestressing at H-type compression reinforcements using unbonded PS tendon. The purpose of compressive prestressing is to recover plastic displacement of PSC girder after long term service by releasing the prestressing. The static test composed of 4 different stages in 3-point bending test is performed to verify safety of the bridge. First stage loading is applied until tensile cracks form. Then in second stage, the load is removed and the girder is unloaded. In third stage, after removal of loading, recovery of remaining plastic deformation is verified as the compressive prestressing is removed at H-type reinforcements. Then, in fourth stage, loading is continued until the girder fails. The experimental results showed that the first crack occurs at 1,615 kN with a corresponding displacement of 187.0 mm. The introduction of the additional compressive stress in the lower part of the girder from the removal of unbonded compressive prestressing of the H-type steel showed a capacity improvement of about 60% (7.7 mm) recovery of the residual deformation (18.7 mm) that occurred from load increase. By using prestressed H-type steel as compression reinforcements in the upper part of cross section, repair and rehabilitation of PSC girders are relatively easy, and the cost of maintenance is expected to decrease.

• Journal of Ethics
• /
• no.88
• /
• pp.103-122
• /
• 2013

This paper aims to study on conceptual suitability or unfitness of Silhak(實學). It is general that by criticizing Chujahak(朱子學) or beyond the limitation of Seonglihak(性理學), Silhak has developed practical tendency to reforming the society in the middle and end of Chosen Dynasty, related to the context of Korean national reflection in modern times. However, it is unfortunate to be understood. As presented in Chosenwangjosillok(『朝鮮王朝實錄』), there has been a few usages in the term 'Silhak'. In short, it was different from its contemporary meaning. At that time, it was usually used to have the meaning of Gyunghak(經學), compared to Sajanghak(詞章學), or rarely, of 'the true study' or 'the practical study'. Therefore, it is to claim that its conception has been manipulated or exaggerated very seriously. Since 1930s, in particular, its conception has been misused in interpreting works of Jung Yak-Yong by some scholars, such as Jung In-Bo, Moon Il-Pyung and An Jae-Hong, who tried to apply the term to overcome the Japanese colonial era symbolised as modernity based on the future life of Korea. Even though their attempt has led to have crucial discussions on the conceptions of Silhak, it has an unnecessary result that there has been a new and totally different understanding of Silhak in South Korea, North Korea, China, Japan, etc., which means that the unsustainable conception of Silhak has been one of major problems in studying of Silhak. To give an practical solution, I would try to make sense of 'time spirit' whose scholars studied Silhak in the middle and end of Chosen Dynasty. A problem, however, is that a scholar group in the name of Bukhakpa(北學派) had certain links and bonds. This is because many scholars studying of Silhak were usually features out of the main stream, which made them it difficult to form any various groups. That is to say, it seems to be natural that they have dreamed of utopian imaginations less than of overlapping points in reality. To sum up, it would be concluded at least that any approach to human lives and thoughts in the given conceptions of Silhak, e.g. ethical thoughts of Silhak, enables us to be indifferentiated to take its true meaning and time spirit of Chosen Dynasty. To be disenchanted of its social roles in Chosen Dynasty, fundamentally, it should be escaped from the wrong net of illusions and sings in understanding Silhak in certain eclectic steps.

• Asia Marketing Journal
• /
• v.12 no.4
• /
• pp.165-181
• /
• 2011

In 2005, Yuhan Kimberly found interesting points in the existing customers' U&A survey on the kitchen towel. The usage of Korean consumers is usually restricted to getting rid of the oil from the fans and the fried food. This usage limits could be the barrier to the diffusion of kitchen towel. Although consumers were worried about the hygiene situations about the dishcloth, they also percieved that the existing paper kitchen towels were short of something to soothe their inconveniences. As a result, the company made a decision to seek out the solution for the consumers' worries. The relative shortage of the paper kitchen towel compared to that of the unhygienic and inconvenient dishcloth was its lack of water-endurance. The dishcloth could be reliable in the wet environment which is very common in Korean kitchen, whereas the paper kitchen towel was perceived as very weak and unreliable in removing water form the dishes and the sink. To overcome the common sense of the consumers, it is important to shift the consumers' perception of the kitchen towel category. It is needed to expand the usage time from one time to several times in a day. So it is needed to redesign the customers' kitchen life. The company adopted the brand "Scott^®" to meet the global brand strategy of the parent company, Kimberley Clark. This brand was also adopted and made a succesful launch of the similar product lines in Latin America. Furthermore, to make an emphasis on the differentiation from the existing paper kitchen towels, the company made the slogan, "Scott^® washable kitchen towel." This slogan was designed to expand the familiar product image of convenient paper towels to water-resistance. As a result, consumers show the changes in usage behavior of paper towels and apply them for more various purposes such as cleaning the decks and tables. This change results in the rapid sales increase of "Scott^® washable kitchen towel."

• Journal of Science Education
• /
• v.48 no.1
• /
• pp.15-30
• /
• 2024

This study aimed to analyze students' cognitive levels and the cognitive demands of mathematical concepts related to science to understand why students struggle to comprehend scientific concepts and tend to avoid learning them. Initially, the mathematics and science curricula of the 2015 revised curriculum were examined to extract learning elements related to mathematics within middle school science content. The Curriculum Analysis Taxonomy (CAT) was then employed to analyze the cognitive levels required by the learning content. In the domain of chemistry, among a total of 20 learning elements related to mathematics, 12 required an understanding at the level of initial formal manipulation (3A), while 3 necessitated comprehension at the level of later formal manipulation (3B). It was noted that cognitive logic types such as proportional reasoning, mathematical manipulation, and measurement skills were prominently employed in elements corresponding to both 3A and 3B. As for biology, out of 7 learning elements related to mathematics, 3 required an understanding at the level of initial formal manipulation (3A), and 2 necessitated comprehension at the level of later formal manipulation (3B). Elements corresponding to both 3A and 3B in biology predominantly involved correlational logic, indicating a somewhat different cognitive challenge compared to the domain of chemistry. Considering that the average percentage of middle school students capable of formal thinking, as analyzed through the GALT short form, was 12.1% for the first year, 16.6% for the second year, and 29.3% for the third year, it can be concluded that the cognitive demands of mathematics-related chemistry and biology learning content are relatively high compared to students' cognitive levels.

• Korean Journal of Environmental Biology
• /
• v.42 no.1
• /
• pp.80-94
• /
• 2024

This study aimed to examine the morphological characteristics and variation in main traits by comparing the growth of individuals of Ecklonia cava Kjellman(Laminariales, Phaeophyceae) under an aquaculture environment. This survey was conducted from April 2018 to November 2019 at the aquafarm in Jindo-gun, Jeollanam-do(South coast of Korea). To classify the morphology of individuals in the aquaculture farm of E. cava, we investigated fourteen morphological characteristics and calculated four ratios between the measured values. Juvenile individuals showed a simple or oblong lanceolate, and at 3-4 months, a short stipe and holdfast developed, along with a bladelet that developed into the secondary blade form. At 5-7 months, secondary blades were found to develop irregularly on the primary blade. At 8-10 months, the primary blade expanded and secondary blades elongated. At 11-12 months, the secondary blades became oblong. At 13-14 months, the thallus area expanded. At 15-16 months, tertiary blades were formed, the thallus became more complex, the stipe thickened, and the holdfast widened. At 17-18 months, secondary blades clearly developed along with lobes. At 19-20 months, tertiary blades developed and became similar to mature natural blades. In the principal component analysis (PCA), the monthly population of the first year(Q1) and that of the second year(Q2) of the cultured population were divided along PC1, which is related to secondary blade morphological characteristics and the holdfast width. Q2 and natural populations are distributed in descending order of volume in Jeju(J), East Coast(E), and South Coast(S) along PC2, which is related to primary blade and stipe morphological characteristics. The results of this study were judged to offer important criteria for the development of different varieties of E. cava.

• Journal of Korean Society of Forest Science
• /
• v.36 no.1
• /
• pp.9-25
• /
• 1977

As a successive work of the variation studies of natural Pinus densiflora stands, some characteristics of individual trees of the three natural populations selected from the Kwang-won Province, the middle-east part of Korean peninsula, as shown in the location map, were investigated. And the statiscal differences between individuals within population, and between populations were analysed. Twenty trees from each population were selected for this study purpose. Doing this, those trees lagged in growth, usually showing poorer form, were eliminated. The results obtained are summarized as follows: 1. Though the average population ages had the ranage between 50 and 63, the growth of height or diameter was similar. Population No.9 is, however, considered to have better tree forms at glance. Population No.8 showed the heighest value not only in the clear-stem-length ratio. 0.53 but also in the crown-index 0.91. The higher value can be result from those trees having long lateral branches and relatively short crown height, meaning undesirable crown shape. In regard to the fine branchedness and the acuteness of branching angle, the population No.9. is considered to be a better one, whereas there was almost no difference in crown height among populations. 2. Checking the frequency distributions of the ratio of the clear-stem-height to the total height and the crown-indices, some difference between populations are considered. These might be attributed to the previous way of stand mangement which alters the density. 3. In the serration density, the average number of 54 per 1cm needle length, the significant differences exist between individual trees within population but not between populations. A few trees which extremly high serration density were observed. As in serration, so tendencies were in the number of stomata row and resin duct. 4. The population 8 had the resin duct index value of 0.074 as the highest which was twice or triple of the other ones. 5. The patterns of increasing process of the average 10-year-ring-segment were not similar till the 30 years of age, but beyond this, the tendency lines were aggregated. 6. Regading the average summer wood ratio, no diffrence between populations, but in the ranges, i.e. 23 to 30 in population No.8. and 16 to 36 in population No.9., with regad to the specific gravity of wood, there were hardly observed any difference between populations even in the ranges values. As the increase of tree ages, the increase of specific gravity was followed but the increasing patterns were not similar between populations. 7. No significant differences between populations in the average tracheid length and the range were detected. However, the length was increased according to the age increase. The increasing pattern was same between populations.

• Journal of Intelligence and Information Systems
• /
• v.26 no.2
• /
• pp.1-25
• /
• 2020

In this paper, we suggest an application system architecture which provides accurate, fast and efficient automatic gasometer reading function. The system captures gasometer image using mobile device camera, transmits the image to a cloud server on top of private LTE network, and analyzes the image to extract character information of device ID and gas usage amount by selective optical character recognition based on deep learning technology. In general, there are many types of character in an image and optical character recognition technology extracts all character information in an image. But some applications need to ignore non-of-interest types of character and only have to focus on some specific types of characters. For an example of the application, automatic gasometer reading system only need to extract device ID and gas usage amount character information from gasometer images to send bill to users. Non-of-interest character strings, such as device type, manufacturer, manufacturing date, specification and etc., are not valuable information to the application. Thus, the application have to analyze point of interest region and specific types of characters to extract valuable information only. We adopted CNN (Convolutional Neural Network) based object detection and CRNN (Convolutional Recurrent Neural Network) technology for selective optical character recognition which only analyze point of interest region for selective character information extraction. We build up 3 neural networks for the application system. The first is a convolutional neural network which detects point of interest region of gas usage amount and device ID information character strings, the second is another convolutional neural network which transforms spatial information of point of interest region to spatial sequential feature vectors, and the third is bi-directional long short term memory network which converts spatial sequential information to character strings using time-series analysis mapping from feature vectors to character strings. In this research, point of interest character strings are device ID and gas usage amount. Device ID consists of 12 arabic character strings and gas usage amount consists of 4 ~ 5 arabic character strings. All system components are implemented in Amazon Web Service Cloud with Intel Zeon E5-2686 v4 CPU and NVidia TESLA V100 GPU. The system architecture adopts master-lave processing structure for efficient and fast parallel processing coping with about 700,000 requests per day. Mobile device captures gasometer image and transmits to master process in AWS cloud. Master process runs on Intel Zeon CPU and pushes reading request from mobile device to an input queue with FIFO (First In First Out) structure. Slave process consists of 3 types of deep neural networks which conduct character recognition process and runs on NVidia GPU module. Slave process is always polling the input queue to get recognition request. If there are some requests from master process in the input queue, slave process converts the image in the input queue to device ID character string, gas usage amount character string and position information of the strings, returns the information to output queue, and switch to idle mode to poll the input queue. Master process gets final information form the output queue and delivers the information to the mobile device. We used total 27,120 gasometer images for training, validation and testing of 3 types of deep neural network. 22,985 images were used for training and validation, 4,135 images were used for testing. We randomly splitted 22,985 images with 8:2 ratio for training and validation respectively for each training epoch. 4,135 test image were categorized into 5 types (Normal, noise, reflex, scale and slant). Normal data is clean image data, noise means image with noise signal, relfex means image with light reflection in gasometer region, scale means images with small object size due to long-distance capturing and slant means images which is not horizontally flat. Final character string recognition accuracies for device ID and gas usage amount of normal data are 0.960 and 0.864 respectively.

• Journal of Intelligence and Information Systems
• /
• v.27 no.1
• /
• pp.191-207
• /
• 2021

Up to this day, mobile communications have evolved rapidly over the decades, mainly focusing on speed-up to meet the growing data demands of 2G to 5G. And with the start of the 5G era, efforts are being made to provide such various services to customers, as IoT, V2X, robots, artificial intelligence, augmented virtual reality, and smart cities, which are expected to change the environment of our lives and industries as a whole. In a bid to provide those services, on top of high speed data, reduced latency and reliability are critical for real-time services. Thus, 5G has paved the way for service delivery through maximum speed of 20Gbps, a delay of 1ms, and a connecting device of 106/㎢ In particular, in intelligent traffic control systems and services using various vehicle-based Vehicle to X (V2X), such as traffic control, in addition to high-speed data speed, reduction of delay and reliability for real-time services are very important. 5G communication uses high frequencies of 3.5Ghz and 28Ghz. These high-frequency waves can go with high-speed thanks to their straightness while their short wavelength and small diffraction angle limit their reach to distance and prevent them from penetrating walls, causing restrictions on their use indoors. Therefore, under existing networks it's difficult to overcome these constraints. The underlying centralized SDN also has a limited capability in offering delay-sensitive services because communication with many nodes creates overload in its processing. Basically, SDN, which means a structure that separates signals from the control plane from packets in the data plane, requires control of the delay-related tree structure available in the event of an emergency during autonomous driving. In these scenarios, the network architecture that handles in-vehicle information is a major variable of delay. Since SDNs in general centralized structures are difficult to meet the desired delay level, studies on the optimal size of SDNs for information processing should be conducted. Thus, SDNs need to be separated on a certain scale and construct a new type of network, which can efficiently respond to dynamically changing traffic and provide high-quality, flexible services. Moreover, the structure of these networks is closely related to ultra-low latency, high confidence, and hyper-connectivity and should be based on a new form of split SDN rather than an existing centralized SDN structure, even in the case of the worst condition. And in these SDN structural networks, where automobiles pass through small 5G cells very quickly, the information change cycle, round trip delay (RTD), and the data processing time of SDN are highly correlated with the delay. Of these, RDT is not a significant factor because it has sufficient speed and less than 1 ms of delay, but the information change cycle and data processing time of SDN are factors that greatly affect the delay. Especially, in an emergency of self-driving environment linked to an ITS(Intelligent Traffic System) that requires low latency and high reliability, information should be transmitted and processed very quickly. That is a case in point where delay plays a very sensitive role. In this paper, we study the SDN architecture in emergencies during autonomous driving and conduct analysis through simulation of the correlation with the cell layer in which the vehicle should request relevant information according to the information flow. For simulation: As the Data Rate of 5G is high enough, we can assume the information for neighbor vehicle support to the car without errors. Furthermore, we assumed 5G small cells within 50 ~ 250 m in cell radius, and the maximum speed of the vehicle was considered as a 30km ~ 200 km/hour in order to examine the network architecture to minimize the delay.

• MISULJARYO - National Museum of Korea Art Journal
• /
• v.100
• /
• pp.140-170
• /
• 2021

This paper investigates the Wooden Seated Tri-kaya Buddha Images(三身佛像) of Vairocana, Rushana, and Sakyamuni enshrined in Daeungjeon Hall of Hwaeomsa temple(華嚴寺) in Gurae, South Cheolla Province. They were produced in 1634 CE and placed in 1635 CE, about forty years after original images made in the Goryeo period were destroyed by the Japanese army during the war. The reconstruction of Hwaeomsa was conducted by Gakseong, one of the leading monks of Joseon Dynasty in the 17th century, who also conducted the reconstructions of many Buddhist temples after the war. In 2015, a prayer text (dated 1635) concerning the production of Hwaeomsa Tri-kaya Buddha images was found in the repository within Sakyamuni Buddha. It lists the names of participants, including royal family members (i.e., prince Yi Guang, the eighth son of King Seon-jo), and their relatives (i.e., Sin Ik-seong, son-in-law of King Seonjo), court ladies, monk-sculptors, and large numbers of monks and laymen Buddhists. A prayer text (dated 1634) listing the names of monk-sculptors written on the wooden panel inside the pedestal of Rushana Buddha was also found. A recent investigation into the repository within Rushana Buddha in 2020 CE has revealed a prayer text listing participants producing these images, similar to the former one from Sakyamuni Buddha, together with sacred relics of hoo-ryeong-tong copper bottle and a large quantity of Sutra books. These new materials opened a way to understand Hwaeomsa Trikaya images, including who made them and when they were made. The two above-mentioned prayer texts from the repository of Sakyamuni and Rushana Buddha statues, and the wooden panel inside the pedestal of Rushan Buddha tell us that eighteen monk-sculptors, including Eungwon, Cheongheon and Ingyun, who were well-known monk artisans of the 17th century, took part in the construction of these images. As a matter of fact, Cheongheon belonged to a different workshop from Eungwon and Ingyun, who were most likely teacher and disciple or senior and junior colleagues, which means that the production of Hwaeomsa Tri-kaya Buddha images was a collaboration between sculptors from two workshops. Eungwon and Ingyun seem to have belonged to the same community studying under the great Buddhist priest Seonsu, the teacher of Monk Gakseong who was in charge of the reconstruction of Haweonsa temple. Hwaeomsa Tri-kaya Buddha images show a big head, a squarish face with plump cheeks, narrow and drooping shoulders, and a short waist, which depict significant differences in body proportion to those of other Buddha statues of the first half of 17th century, which typically have wide shoulders and long waists. The body proportion shown in the Hwaeomsa images could be linked with images of late Goryeo and early Joseon period. Rushana Buddha, raising his two arms in a preaching hand gesture and wearing a crown and bracelets, shows unique iconography of the Bodhisattva form. This iconography of Rushana Buddha had appeared in a few Sutra paintings of Northern Song and Late Goryeo period of 13th and 14th century. BodhaSri-mudra of Vairocana Buddha, unlike the general type of BodhaSri-mudra that shows the right hand holding the left index finger, places his right hand upon the left hand in a fist. It is similar to that of Vairocana images of Northern and Southern Song, whose left hand is placed on the top of right hand in a fist. This type of mudra was most likely introduced during the Goryeo period. The dried lacquer Seated Vairocana image of Bulheosa Temple in Naju is datable to late Goryeo period, and exhibits similar forms of the mudra. Hwaeomsa Tri-kaya Buddha images also show new iconographic aspects, as well as traditional stylistic and iconographic features. The earth-touching (bhumisparsa) mudra of Sakymuni Buddha, putting his left thumb close to the middle finger, as if to make a preaching mudra, can be regarded as a new aspect that was influenced by the Sutra illustrations of the Ming dynasty, which were imported by the royal court of Joseon dynasty and most likely had an impact on Joseon Buddhist art from the 15th and 16th centuries. Stylistic and iconographical features of Hwaeomsa Tri-kaya Buddha images indicate that the traditional aspects of Goryeo period and new iconography of Joseon period are rendered together, side by side, in these sculptures. The coexistence of old and new aspects in one set of images could indicate that monk sculptors tried to find a new way to produce Hwaeomsa images based on the old traditional style of Goryeo period when the original Tri-kaya Buddha images were made, although some new iconography popular in Joseon period was also employed in the images. It is also probable that monk sculptors of Hwaeomsa Tri-kaya Buddha images intended to reconstruct these images following the original images of Goryeo period, which was recollected by surviving monks at Hwaeomsa, who had witnessed the original Tri-kaya Buddha images.

• Journal of Venture Innovation
• /
• v.5 no.3
• /
• pp.57-70
• /
• 2022

In modern industrial capitalism, the relationship between the provision of work and the receipt of wages has become an important principle governing society. According to the labor contract, the wages provided by entrusting the right to dispose of one's labor to the employer are directly compensated, and human life should be guaranteed and reproduced with proper rest. The establishment of labor relations under free contracts represents a problem in protecting workers, and accordingly, the maximum of working hours is set as a minimum right for workers, and the standard for minimum rest is set and assigned. The reduction of working hours is very important in terms of the quality of life of workers, but it is also an important issue in efficient corporate activities. As of 2020, Korea has 1,908 hours of annual working hours, the third lowest among OECD 37 countries in the happiness index surveyed by the Sustainable Development Solution Network(SDSN), an agency under the United Nations. Accordingly, the necessity of reducing working hours has been recognized, and the maximum working hours per week has been limited to 52 hours since 2018. In this situation, various working hours are legally excluded as a way to maintain the company's value-added creation and meet the diverse needs of workers, and Korea's Labor Standards Act restricts flexible working hours within three months, flexible working hours exceeding three months, selective working hours, and extended working hours. However, in the discussion on the application of the revised flexible working hours system in 2021 and the expansion of the settlement unit period recently discussed, there is a problem with the flexible working hours system, which needs to be improved. Therefore, this paper aims to examine the problems of the flexible working hours system and improvement measures. The flexible working hours system is a system that does not violate working hours even if the legal working hours are exceeded on a specific day or week according to a predetermined standard, and does not have to pay additional wages for excessive overtime work. It is mainly useful as a form of shift work in manufacturing, sales service, continuous business or electricity, gas, water, and transportation for long-term operations. It is also used as a way to shorten working hours, such as expanding holidays through short working days. However, if the settlement unit period is expanded, it is disadvantageous to workers as the additional wages that workers can receive will not be received. Therefore, First, in order to expand the settlement unit period currently under discussion, additional wages should be paid for the period expanded from the current standard. Second, it is necessary to improve the application of the flexible working hours system to individual workers to have sufficient consultation with individual workers in a written agreement with the worker representative, Third, clarify the allowable time for extended work during the settlement unit period, and Fourth, limit the daily working hours or apply to continuous rest. In addition, since the written agreement of the worker representative is an important issue in the application of the flexible working hours system, it is necessary to secure the representation of the worker representative.