• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.1
• /
• pp.53-58
• /
• 2003

Carbon fiber sheet has been used to rehabilitate many types of reinforced concrete members with its superior characteristics such as their lightweight, high strength, corrosion resistance, and easy execution. But the failure behavior of reinforced concrete members show a high variation by the bond characteristics between carbon fiber sheet and concrete surface. In this study, a bond stress-slip model, which accounts for changes in bonding behavior between concrete and carbon fiber sheet with some link elements, is proposed. The link elements are used to represent the concrete-carbon fiber sheet interface. To investigate the efficiency of this method, the analytical solutions for the behavior of reinforced concrete beam strengthened with carbon fiber sheet are compared with experimental ones. Results from the proposed model comparatively well agree with the experimental results.

• Journal of the Korean Ceramic Society
• /
• v.45 no.5
• /
• pp.276-279
• /
• 2008

In this research, properties of $N_2$-doped $Sb_2Te_3$ thin film were evaluated using 4-point probe, XRD and AFM. $Sb_2Te_3$ material has faster crystallization rate than $Ge_2Sb_2Te_5$, but sheet resistance difference between amorphous and crystallization state is very low. This low sheet resistance difference decreases sensing margin in reading operation at PRAM device operation. Therefore, in order to overcome this weak point, $N_2$ gas was doped on $Sb_2Te_3$ thin film. Sheet resistance difference between amorphous and crystallized state of $N_2$-doped $Sb_2Te_3$ thin film showed about $10^4$ times higher than Un-doped $Sb_2Te_3$ thin film because of the grain boundary scattering.

• Journal of the Korean institute of surface engineering
• /
• v.47 no.4
• /
• pp.186-191
• /
• 2014

Double layer films which consisted of aluminum(Al) and magnesium(Mg) have been prepared by e-beam deposition. The structure, alloy phase, and corrosion resistance of the prepared films were investigated before and after heat treatment. The first (bottom) layer fixed with Al, and the thickness ratio between Al and Mg layers has been changed from 1 : 1 to 5 : 1, respectively. Total thickness of Al-Mg film was fixed at $3{\mu}m$. The cold-rolled steel sheet was used as a substrate. Heat treatment was fulfilled in an nitrogen atmosphere at the temperature of $400^{\circ}C$ for 2, 3 and 10 min. Surface morphology of as-deposited Al-Mg film having Mg top layer showed plate-like structure. The morphology was not changed even after heat treatment. However, cross-sectional morphology of Al-Mg films was drastically changed after heat treatment, especially for the samples heat treated for 10 min. The morphology of as-deposited films showed columnar structure, while featureless structure of the films appeared after heat treatment. The x-ray diffraction data for as-deposited Al-Mg films showed only pure Al and Mg peaks. However, Al-Mg alloy peaks such as $Al_3Mg_2$ and $Al_{12}Mg_{17}$ appeared after heat treatment of the films. It is believed that the formation of Al-Mg alloy phase affected the structure change of Al-Mg film. It was found that the corrosion resistance of Al-Mg film was increased after heat treatment.

• Applied Chemistry for Engineering
• /
• v.20 no.6
• /
• pp.622-627
• /
• 2009

Using an alkali-solution developable photosensitive resin and a carbon black as a conductive filler, photo-patternable pastes for polymer thick film resistor were fabricated and evaluated. A photo solder resist (PSR), which is usually used as protecting layer of printed circuit board (PCB), was used as a photosensitive resin so that ultraviolet exposure and alkali-aqueous solution development of paste were possible. After fabricating the photosensitive polymer resistor paste, the electrical properties of thick film resistors were measured using PCB test boards. Sheet resistance was decreased with increasing amount of carbon black, but the developability was limited in excess loading of carbon black. The sheet resistance was also reduced by re-curing and the change rate was smaller in higher carbon black loading. Moreover, finely patterned meander-type thick film resistors were fabricated using photo-process and large resistance up to several tens of sheet resistance could be obtained in small area by this technique.

• Korean Journal of Materials Research
• /
• v.14 no.6
• /
• pp.389-393
• /
• 2004

The silicide layer used as a diffusion barrier in microelectronics is typically required to be below 50 nm-thick and, the same time, the silicides also need to have low contact resistance without agglomeration at high processing temperatures. We fabricated Si(100)/15 nm-Ni/15 nm-Co samples with a thermal evaporator, and annealed the samples for 40 seconds at temperatures ranging from $700^{\circ}C$ to $1100^{\circ}C$ using rapid thermal annealing. We investigated microstructural and compositional changes during annealing using transmission electron microscopy and auger electron spectroscopy. Sheet resistance of the annealed sample stack was measured with a four point probe. The sheet resistance measurements for our proposed Co/Ni composite silicide was below 8 $\Omega$/sq. even after annealing $1100^{\circ}C$, while conventional nickel-monosilicide showed abrupt phase transformation at $700^{\circ}C$. Microstructure and auger depth profiling showed that the silicides in our sample consisted of intermixed phases of $CoNiSi_{x}$ and NiSi. It was noticed that NiSi grew rapidly at the silicon interface with increasing annealing temperature without transforming into $NiSi_2$. Our results imply that Co/Ni composite silicide should have excellent high temperature stability even in post-silicidation processes.

• Journal of the Korean institute of surface engineering
• /
• v.54 no.3
• /
• pp.119-123
• /
• 2021

SnO₂ single layer and SnO₂/Ag/SnO₂ (SAS) tri-layered films were deposited on the glass substrate by RF and DC magnetron sputtering at room temperature and then the effect of Ag interlayer on the opto-electrical performance of the films were considered. As deposited SnO₂ films show a visible transmittance of 85.5 % and a sheet resistance of 1.2×10⁴ Ω/□, the SAS films with a 15 nm thick Ag interlayer show a lower resistance of 18.8 Ω/□ and a visible transmittance of 70.6 %, respectively. The figure of merit based on the optical transmittance and sheet resistance revealed that the Ag interlayer in the SnO₂ films enhances the opto-electrical performance without substrate heating or annealing process.

• Korean Journal of Materials Research
• /
• v.19 no.9
• /
• pp.488-493
• /
• 2009

Thin films of single-wall carbon nanotubes (SWNT) with various thicknesses were fabricated, and their optical and electrical properties were investigated. The SWNTs of various thicknesses were directly coated in the arc-discharge chamber during the synthesis and then thermally and chemically purified. The crystalline quality of the SWNTs was improved by the purification processes as determined by Raman spectroscopy measurements. The resistance of the film is the lowest for the chemically purified SWNTs. The resistance vs. thickness measurements reveal the percolation thickness of the SWNT film to be $\sim$50 nm. Optical absorption coefficient due to Beer-Lambert is estimated to be $7.1{\times}10^{-2}nm^{-1}$. The film thickness for 80% transparency is about 32 nm, and the sheet resistance is 242$\Omega$/sq. The authors also confirmed the relation between electrical conductance and optical conductance with very good reliability by measuring the resistance and transparency measurements.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.4
• /
• pp.173-178
• /
• 2003

In this paper, we studied the physical and electrical characteristics of $\textrm{WSi}_{x}$ thin film with respect to the adoption of the DCS (dichlorosiliane) post flow and the variation of deposition temperature. XRD measurements show that as deposited thin film has a hexagonal structure regardless of deposition Process. However, we find that the phase of thin film has changed to a tetragonal structure after the heat treatment at $680^{\circ}C$. Adoption of DCS post flow and increment of deposition temperature result in the increments of Si/W composition ratio. These conditions also result in the increment of sheet resistance by the amount 3.0~4.2$\Omega$/$\square$, but give the tendency in the decrement of stress by 0.27~0.3 E10dyne/$\textrm{cm}^2$. We also find that the contact resistance of word line and bit line interconnection was decreased by the amount 5.33~16.43$\mu$$\Omega$-$\textrm{cm}^2$, when applying DCS post flow and increasing deposition temperature.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.91-91
• /
• 2011

The quality of the surface layer in concrete structures plays an important role in the durability of the concrete. The concrete factory products are made as they improve the appearance of the surface and compressive strength in need. A common criterion to judge the quality of concrete products frequently seen in our daily life appears to be "beauty" in terms of consistent shaping. However, as for most concrete curb in such areas where a large amount of anti-freezing agents(NaCl) and ice and snow melting agents(CaCl2) are spread over roads to ensure road safety during the winter season, since deterioration advances from the surface, scaling is seen on the surface concrete due to deterioration which combined freezing damage and salt damage. Especially, In cold northern districts, the spreading amount of deicing salts increases by regulation of studded tire use, and the scaling of the concrete products, the various parts of concrete structures for roads is increasing in recent years. In this study, L-shape concrete curb were targeted, the permeable form method with the commercial permeable sheet was applied to it and the improvements of the quality were examined. By the permeable form method, surface layers got strengthened, which prevented permeation of the deterioration factor from the outside, and the scaling resistance of the upper surface where the permeable sheet was applied improved exceedingly. It will be expected by applying the permeable form method to various concrete products that frost resistance improves and scaling damage decreases.

• Corrosion Science and Technology
• /
• v.10 no.1
• /
• pp.24-29
• /
• 2011

The greatest purpose of chromate treatment is to improve anti-corrosion by stabilizing a metal surface. Because metal surface forms a compound by absorbing oxygen or water in the air by being generally unstable, it is necessary to improve anti-corrosion of the metal by forming the metal surface with a stable film. When considering the economical efficiency and requirements together because the film of the metal surface treated with chromate has good anti-corrosion and the stability also in the air by being compact and strong, Chromate treatment has been used most up to the electronics industry from the auto industry. However, these days, because hexavalent chromium is both a toxic agent to be able to cause cancers and deadly poisonous environmental pollutant, the strong legal controls on its use is being imposed all over the world. Because of this reason, a new anti-corrosion method is being required. Also, by users' various demands, the passivations that have recently been developed require various characteristics such as conductivity, chemical resistance, alkali cleaning resistance as well as anti-corrosion. We could confirm the results such as excellent anti-corrosion compared to chromate, conductivity, chemical resistance and detergent resistance as the result of analysis of various characteristics of the galvannealed sheet steels coated with Cr-Free solution developed in this research.