• 한국분말재료학회지
• /
• 제1권1호
• /
• pp.60-65
• /
• 1994

When a commercial prealloyed Fe-powder(Fe-5Cr-lMo-2Cu-0.5P-3C) is liquid phase sintered at 116$0^{\circ}C$, liquid precipitates with various shapes form within solid grains during the initial stage of sintering. The shape of a liquid precipitate changes pith the increment of their size from sphere(with radius<0.3$\mu\textrm{m}$), a transient polyhedron with more than 7 faces(1~2 $\mu\textrm{m}$), cuboid(3~5 $\mu\textrm{m}$), and finally to sphere(>5 $\mu\textrm{m}$). The shapes of liquid precipitates closely resemble the growth shapes predicted on the basis of solid-liquid interfacial energy and the coherency strain energy with anisotropic elastic constants in the diffusion zone around the precipitates.

• Geomechanics and Engineering
• /
• 제14권1호
• /
• pp.71-81
• /
• 2018

Soils are mostly nonhomogeneous and anisotropic in nature. In this study, nonhomogeneity and anisotropy of soil are taken into consideration by assuming that the cohesion increases with depth linearly and also varies with respect to direction at a particular point. A three-dimensional rotational failure mechanism is adopted, and then a three-dimensional stability analysis of slope is carried out with the failure surface in the shape of a curvilinear cone in virtue of the limit analysis method. A quasistatic approach is used to develop stability charts in nonhomogeneous and anisotropic soils. One can easily read the safety factors from the charts without the need for iterative procedures for safety factors calculation. The charts are of practical importance to prevent a plane failure in excavation slope whether it is physically constrained or not. Then the most suitable location of piles within the reinforced slope in nonhomogeneous and anisotropic soils is explored, as well as the interactions of nonhomogeneous and anisotropic coefficients on pile reinforcement effects. The results indicate that piles are more effective when they are located between the middle and the crest of the slope, and the nonhomogeneous coefficient as well as the anisotropic coefficient will not only influence the most suitable location for piles but also affect the calculated safety factor of existing reinforced slope. In addition, the two coefficients will interact with each other on the effect on slope reinforcement.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2003년도 하계학술연구발표회 및 한.일 공동심포지엄
• /
• pp.194-194
• /
• 2003

As a result of the recent miniaturization an enhancement in the performance of thin film inductors and thin film transformers, there are increased demands for the thin films with high magnetic permeability in the high frequency range, high saturation magnetization, in high electrical resistivity, and low coercive force. In order to improve high frequency properties, we will investigate anisotropy field by shape and size of pattern. The Fe-Al-O thin films of 16mm and 1 $\mu\textrm{m}$ thickness were deposited on Si wafer, using RF magnetron reactive sputtering technique with the mixture of argon and oxygen gases. The fabricating conditions are obtained in the working partial pressure of 2mTorr, O$_2$ partial pressure of 5%, input power of 400W, and Al pellets on an Fe disk with purity of 99,9%. Magnetic properties of the continuous films as followed: the 4$\pi$M$\_$s/ of 19.4kG, H$\_$c/ of 0.6Oe, H$\_$k/ of 6.0Oe and effective permeability of 2500 up to 100㎒ were obtained. In this work, we expect to enhance effect of magnetic anisotropy on patterned of Fe-Al-O thin films.

• 한국자기학회지
• /
• 제4권1호
• /
• pp.25-31
• /
• 1994

코발트와 철의 이온을 혼합한 산성수용액 중에서, 알루미늄 양극산화피막에 전해석출 하여 제작된 자성막은, 코발트조성이 증가함에 따라 발크합금의 경우와 마찬가지로 상전이(phase shifting) 하였다. 입자직경이 $150\;{\AA}$의 시료의 경우 조성이 25-35 at% Co에서 큰 포화자화, 고항자력, 큰 자기이방성 에너지 및 우수한 각형비 등에 기인하는 큰 자기에너지 적($BH_{max}$)이 얻어진다. 그러나 입자직경이 $450\;{\AA}$의 경우에는, 코발트가 50-70 at% 일때 초기석출부 에 강자성체인 FeC가 아주 강하게 배향하므로, 입자의 큰 형상이방성(수직자기이방성)이 없어지고 면내 방향의 자기이방성을 나타낸다. 그리고 같은 조성에서 초기석출부를 제거하여 FeC의 영향을 없앨때, 주직자기이방성이 회복되었다.

• 청정기술
• /
• 제24권4호
• /
• pp.301-306
• /
• 2018

최근 미세먼지의 증가로 인해 디젤 자동차로부터 발생되는 PM에 대한 규제가 강화되고 있다. 디젤 자동차의 배기가스를 제거하는 후처리 장치인 매연여과장치(diesel particulate filter, DPF)에 대한 관심이 급증하고 있다. 따라서 DPF 효율 향상의 하나로 DPF 내의 압력강하를 줄여서 필터 및 재생(Regeneration)의 효율을 증가시키고 있다. 본 연구에서는 ANSYS FLUENT를 이용하여 5.66" SiC와 Cordierite DPF의 셀 밀도, 채널 형상, 벽두께, 입 출구 채널 비에 따른 압력강하 영향을 시뮬레이션했다. 실험결과로서 200 CPSI보다 300 CPSI에서 압력강하가 작게 나타났으며, Anisotropy과 O/S 셀이 Isotropy보다 약 1,301 Pa 작은 압력강하를 나타냈다. 공극률은 10% 증가할 때 마다 압력강하가 약 300 Pa씩 작아졌고, 벽 두께에 따른 영향은 0.05 mm 두꺼워질수록 약 500 Pa 씩 커지는 경향을 나타냈다.

• Bulletin of the Korean Chemical Society
• /
• 제29권6호
• /
• pp.1131-1136
• /
• 2008

The electrical repulsive energy between two model cylinders was calculated by solving nonlinear Poission- Boltzmann (P-B) equation under Derjaguin approximation. Effects of the surface potential, Debye screening length, and configuration of cylinders on the repulsive interaction energy were examined. Due to the anisotropy of the shape of cylinder, the interaction repulsive energy showed dependence to the configuration of particles; cylinders aligned in end-to-end configuration showed largest repulsive energy and crossed particles had lowest interaction energy. The configuration effect is originated from the curvature effect of the interacting surfaces. The curved surfaces showed less repulsive energy than flat surfaces at the same interacting surface area. The configuration dependency of interaction energy agreed with the previous analytical solution obtained under the linearized P-B equation. The approach and results present in this report would be applicable in predicting colloidal behavior of cylindrical particles.

• 소성∙가공
• /
• 제8권4호
• /
• pp.347-355
• /
• 1999

The paper is concerned with an improved scheme for application of the blank holding force in order to take account of the thickness distribution in the sheet material of the flange region. The scheme incorporates with a modified membrane finite element method for planar anisotropic materials. The new scheme proposed two coefficients α and βto calculate the compressive stress in the sheet metal due to the blank holding force, which should be determined properly for accurate analysis. The effect of αand βon the blank holding force distribution and the deformed shape is investigated with simulation of rectangular cup deep drawing processes by changing parameter values.

• Journal of Magnetics
• /
• 제12권4호
• /
• pp.152-155
• /
• 2007

Spin dependent transport was investigated in lateral $Py(Ni_{81}Fe_{19})/Au/Py$ spin valve devices. Clear spin valve effect was observed in conventional four-terminal measurement geometry. Higher resistance was found in antiparallel magnetization field of two Py electrodes which is determined by anisotropy magnetoresistance (AMR) measurements. The rectangular shape of spin signal together with good agreement of switching field convinces observed spin valve signal is resulted from effective spin injection and detection. The magnetoresistance ratio decays exponentially with channel length by which spin diffusion length of Au channel was estimated to be 76 nm.

• 소성∙가공
• /
• 제9권6호
• /
• pp.615-623
• /
• 2000

The industrial application of hydroforming has a great potential in saying cost and achieving dimensional accuracy in automotive industry presently. The aim of the following article is to investigate the effect of process parameters on hydroformed part. Firstly, we have to investigate the change of mechanical properties for sheet and pipe material according to various radius/thickness ratio(r/t). The change of mechanical properties affects the yield stress more than the total elongation. Increase of yield stress for pipe has a bad influence on formability of hydroforming. Among the roll-forming process, the sizing process didn't change mechanical properties. The process parameters such as the initial pressure, mandrel shape and friction have seriously influenced on formability of hydroforming. Therefore we need to check formability of given material through the FE analysis in the beginning stage of process design and the predicted hydroforming process parameters ate generally a good starting point for the prototype tryout stage. The results of pretending, hydroforming analysis using FE model are good agreement with experimental results.

• 한국결정성장학회지
• /
• 제10권1호
• /
• pp.17-22
• /
• 2000

수직보자력이 크고 CoCrPt에 비하여 noise 저감 효과가 큰 것으로 알려진 CoCrPtTa계 합금박막의 수직이방성을 더욱 개선하기 위해 Ti를 우선 증착하였다. 본 연구에서는 Ti 두께 변화에 따른 비교적 높은 수직보자력치를 보였던 $CoCr_{16.2}Pt_{10.8}Ta_4$Ti/glass 시편에서 자기적 특성과 자구형상의 변화를 살펴보았다. 또한 VSM(Vibrating Sample Magnetometer)을 이용하여 M-H loop를 측정하였으며 자구형상은 MFM(Magnetic Force Microscopy)로 관찰하였다. 육방정 Ti가 하지층으로서 우선증착되면 bare glass 직접 증착되는 경우보다 CoCrPtTa 자성층의 수직이방성에 현저한 향상을 가져왔으며 Ti의 두께가 두꺼울수록 c-축 배향성도 개선되었다. MFM 결과에 의하면 Ti두레가 20 nm에서 90 nm로 증가함에 따라 자구형상이 연속적인 stripe type에서 mass type으로 분절된 형태로 변하였다. 이는 Ti의 증착이 비자성 Cr 편석 거동에 영향을 미쳐 자화반전시 인접 columnar grain의 자화벡터들간의 상호교환작용을 억제하는 자기적 분리 효과에 기여했음을 의미한다. 아울러 이와 같은 거동은 Ti가 CoCr계 자성층의 수직이방성을 개선하는데 있어서 형상자기이방성적인 측면에서의 기여가 현저함을 의미하기도 한다.