• Journal of the Korean Institute of Intelligent Systems
• /
• v.20 no.1
• /
• pp.54-59
• /
• 2010

This paper present to study the guidance system as localization technique using sensor fusion and line tracking technique using virtual line for AGV(autonomous guided vehicle). An existing AGV could drive on decided line only. And representative guidance systems of such guidance system are magnet-gyro guidance and wired guidance. However, those have had the high cost of installation and maintenance, and the difficulty of system change according to variation of working environment. To solve such problems, we make the localization system which is fused with a laser navigation and gyro, encoder. The system is robust against noise, and flexible according to working environment through sensor fusion. For line tracking of laser navigation without wire guidance, we set the virtual line in program, and design the driving controller based on difference of angle and distance between AGV's position and decided virtual line. To experiment, we use the AGV which is made by ourselves, and experiment the line tracking repeatedly on same experimental environment. In result, maximum distance error between decided virtual line and AGV's position was less than 49.93mm, and we verified that the proposed system is efficient for line tracking of actual AGV.

• Journal of the Institute of Convergence Signal Processing
• /
• v.20 no.4
• /
• pp.245-251
• /
• 2019

Sonar bearing accuracy is the correspondence between the target orientation predicted by sonar and actual target orientation, and is obtained from measurements. However, when measuring sonar bearing accuracy, many errors are included in the results because they are made at sea, where complex and diverse environmental factors are applied. In particular, parallax error caused by the difference between the position of the GPS receiver and the sonar sensor, and the time delay error generated between the speed of underwater sound waves and the speed of electromagnetic waves in the air have a great influence on the accuracy. Correcting these parallax errors and time delay errors without an automated tool is a laborious task. Therefore, in this study, we propose a sonar bearing accuracy measurement equipment with parallax error and time delay error correction. The tests were carried out through simulation data and real data. As a result of the test it was confirmed that the parallax error and time delay error were systematically corrected so that 51.7% for simulation data and more than 18.5% for real data. The proposed method is expected to improve the efficiency and accuracy of sonar system detection performance verification in the future.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.37 no.3
• /
• pp.173-178
• /
• 2024

This study presents a technique for assessing the dimensional quality of assembly parts in Prefabricated Steel Structures (PSS) using a stereo vision sensor. The stereo vision system captures images and point cloud data of the assembly area, followed by applying image processing algorithms such as fuzzy-based edge detection and Hough transform-based circular bolt hole detection to identify bolt hole locations. The 3D center positions of each bolt hole are determined by correlating 3D real-world position information from depth images with the extracted bolt hole positions. Principal Component Analysis (PCA) is then employed to calculate coordinate axes for precise measurement of distances between bolt holes, even when the sensor and structure orientations differ. Bolt holes are sorted based on their 2D positions, and the distances between sorted bolt holes are calculated to assess the assembly part's dimensional quality. Comparison with actual drawing data confirms measurement accuracy with an absolute error of 1mm and a relative error within 4% based on median criteria.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.12
• /
• pp.56-63
• /
• 2012

The WBAN technology means a short distance wireless network which provides each device interactive communication by connecting devices inside and outside of body. Standardization on the physical layer, data link layer, network layer and application layer is in progress by IEEE 802.15.6 TG BAN. Wireless body area network is usually configured in energy efficient using sensor and zigbee device due to the power limitation and the characteristics of human body. Wireless sensor network consist of sensor field and sink node. Sensor field are composed a lot of sensor node and sink node collect sensing data. Wireless sensor network has capacity of the self constitution by protocol where placed in large area without fixed position. Mobile sink node distribute energy consumption therefore network life time was increased than fixed sink node. The energy efficient is important matter in wireless body area network because energy resource was limited on sensor node. In this paper we proposed cluster topology algorithm for efficient data transmission in wireless body area network based mobile sink. The proposed algorithm show good performance under the advantage of grid routing protocol and TDMA scheduling that minimized overlap area on cluster and reduced amount of data on cluster header in error prone wireless sensor network based on mobile sink.

• 한국HCI학회:학술대회논문집
• /
• 2009.02a
• /
• pp.701-706
• /
• 2009

We proposed the device to control a computer with only a head and eye blinks so that disabilities by car accidents can use a computer. Because they have paralysis of their upper extremities such as C4~C5 paraplegics and cerebral palsy, they cannot efficiently access a general keyboard/mouse not using hands and foots. The cursor position was estimated from a gyro-sensor which can measure head movements, and the mouse event such as click/double click from opto-sensors which can detect eye blinks. The sensor was put on the proper goggle in order not to disturb the visual field. The performance of the proposed device was compared to a general optical mouse, and was used both relative and absolute coordinate in cursor positioning control. The recognition rate of click and double-click was 86% of the optical mouse, the speed of cursor movement by the proposed device was not much different from the mouse. The overall accuracy was 80%. Especially, the relative coordinate is more convenience and accuracy than the absolute coordinate, and can reduce the frequency of reset to prevent the accumulative error.

• Journal of Advanced Navigation Technology
• /
• v.16 no.3
• /
• pp.417-425
• /
• 2012

It is well known that GPS cannot provide positioning results if sufficient number of visible satellites are not available. To overcome this weak point, attentions have been recently moved to hybrid positioning methods that augments GPS with other sensors. As an extension of hybrid positiong methods, this paper proposes a new method that combines GPS and vision sensor to improve availability and accuracy of land vehicle positioning. The proposed method does not require any external map information and can provide position solutions if more than 2 navigation satellites are visible. To evaluate the performance of the proposed method, an experiment result with real measurements is provided and a result shows that accumulated error of n-axis is almost 2.5meters and that of e-axis is almost 3meters in test section.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.16 no.5
• /
• pp.109-120
• /
• 2017

It is important to estimate objectively in the driving test. Especially, the driving test is examined by totally driving ability, rule observation and situational judgement. For this, a grading automation system for driving test was presented by using GPS, sensor data and equipment operation informations. This system is composed of vehicle mounted module, automatic grading terminal, data controller, data storage and processing server. The vehicle mounted module gathters sensor data in the car. The terminal performs automatic grading using the received sensor data according the driving test criterion. To overcome the misposition of vehicle in the map due to GPS error, we proposed the automatic grading system by map matching method, path deviation and return algorithm. In the experimental results, it was possible to grade automatically, display the right position of the car, and return to the right path under 10 seconds when the vehicle was out of the shadow region of the GPS. This system can be also applied to the driving education.

• Journal of IKEEE
• /
• v.23 no.4
• /
• pp.1302-1308
• /
• 2019

This paper presents an approach for classifying image made by acquired position data from a 2D Lidar sensor with a convolutional neural network (CNN). Lidar sensor has been widely used for unmanned devices owing to advantages in term of data accuracy, robustness against geometry distortion and light variations. A CNN algorithm consists of one or more convolutional and pooling layers and has shown a satisfactory performance for image classification. In this paper, different types of CNN architectures based on training methods, Gradient Descent(GD) and Levenberg-arquardt(LM), are implemented. The LM method has two types based on the frequency of approximating Hessian matrix, one of the factors to update training parameters. Simulation results of the LM algorithms show better classification performance of the image data than that of the GD algorithm. In addition, the LM algorithm with more frequent Hessian matrix approximation shows a smaller error than the other type of LM algorithm.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10b
• /
• pp.382-387
• /
• 1992

In order to obtain desired arc welding performance, we already developed an arc welding robot system that enabled coordinated motions of dual arm robots. In this system one robot arm holds a welding target as a positioning device, and the other robot moves the welding torch. Concerning to such a dual arm robot system, the positioning accuracy of robots is one important problem, since nowadays conventional industrial robots unfortunately don't have enough absolute accuracy in position. In order to cope with this problem, our robot system employed teaching playback method, where absolute error are compensated by the operator's visual feedback. Due to this system, an ideal arc welding considering the posture of the welding target and the directions of the gravity has become possible. Another problem still remains, while we developed an original teaching method of the dual arm robots with coordinated motions. The problem is that manual teaching tasks are still tedious since they need fine movements with intensive attentions. Therefore, we developed a 3-dimensional vision guided robot control method for our welding robot system with coordinated motions. In this paper we show our 3-dimensional vision sensor to guide our arc welding robot system with coordinated motions. A sensing device is compactly designed and is mounted on the tip of the arc welding robot. The sensor detects the 3-dimensional shape of groove on the target work which needs to be weld. And the welding robot is controlled to trace the grooves with accuracy. The principle of the 3-dimensional measurement is depend on the slit-ray projection method. In order to realize a slit-ray projection method, two laser slit-ray projectors and one CCD TV camera are compactly mounted. Tactful image processing enabled 3-dimensional data processing without suffering from disturbance lights. The 3-dimensional information of the target groove is combined with the rough teaching data they are given by the operator in advance. Therefore, the teaching tasks are simplified

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.46 no.4
• /
• pp.70-76
• /
• 2009

We proposed the device to control a computer mouse with only head movements and eye blinks so that disabilities by car or other accidents can use a computer. The mouse position were estimated from a gyro-sensor which can measure head movements, and the mouse events such as click/double click were from opto sensors which can detect the eyes flicker, respectively. The sensor was mounted on the goggle in order not to disturb the visual field. There was no difference in movement speed between ours and a general mouse, but it required 3$\sim$4 more times in the result of the experiment to evaluate spatial movements and events detection of the proposed mouse because of the low accuracy. We could eliminate cumbersome work to periodically remove the accumulated error and intuitively control the mouse using non-linear relative point method with dead zones. Optical sensors are used in the event detection circuitry designed to remove the influence of the ambient light changes, therefore it was not affected in the change of external light source.