• Computational Structural Engineering
• /
• v.4 no.4
• /
• pp.125-133
• /
• 1991

For the purpose of efficiently calculating the design sensitivity and the reliability for the complicated structures in which the structural responses or limit state functions are given by implicit form, the probabilistic finite element method is introduced to formulate the deterministic design sensitivity analysis method and incorporated with the second moment reliability methods such as MVFOSM, AFOSM and SORM. Also, the probabilistic design sensitivity analysis method needed in the reliability-based design is proposed. As numerical examples, two thin plates are analyzed for the cases of plane stress and plate bending. The initial yielding is defined as failure criterion, and applied loads, yield stress, plate thickness, Young's modulus and Poisson's ratio are treated as random variables. It is found that the response variances and the failure probabilities calculated by the proposed PFEM-based reliability method show good agreement with those by Monte Carlo simulation. The probabilistic design sensitivity evaluates explicitly the contribution of each random variable to probability of failure. Further, the design change can be evaluated without any difficulty, and their effect on reliability can be estimated quickly with high accuracy.

• The Journal of the Korea Contents Association
• /
• v.3 no.4
• /
• pp.63-68
• /
• 2003

This paper is to measure the sensitivity of relations in communication network operation. In order to procure an important adequacy in the network operation and quality improvement, it is necessary to increase network operation efficiency and analyze the characteristic of network operation. Finally, we analyze costing appropriate operation, propose profit increase scheme and apply realistic business. First of all it's important to improve and estimate a proper operating cost thoroughly and comprehensively. Because the important issue of this process is quality process and this quality process occurs customers' satisfaction, therefore, to make a mutual relation in-between individual change of each element is to analyze a reasonable standard. So, for this reason we study on structuring nice moods for network operation and estimating many scenarios for measuring efficiency. Especially those in economic and sensitivity based. It will be the development of analyzing methods which suites the service and communication system. The result of this study gives a basis for making a flexible and highly predictable system by pre configured sensitivity analysis of each scenarios.

• Journal of the Korean Geotechnical Society
• /
• v.36 no.8
• /
• pp.49-60
• /
• 2020

A fully coupled thermo-hydro-mechanical model is established to evaluate frost heave behaviour of saturated frost-susceptible soils. The method is based on mass conservation, energy conservation, and force equilibrium equations, which are fully coupled with each other. These equations consider various physical phenomena during one-dimensional soil freezing such as latent heat of phase change, thermal conductivity changes, pore water migration, and the accompanying mechanical deformation. Using the thermo-hydro-mechanical model, a sensitivity analysis study is conducted to examine the effects of the geotechnical parameters and external conditions on the amount of frost heave and frost heaving rate. According to the results of the sensitivity analysis, initial void ratio significantly affects each objective as an individual parameter, whereas soil particle thermal conductivity and temperature gradient affect frost heave behaviour to a greater degree when applied simultaneously. The factors considered in this study are the main factors affecting the frost heaving amount and rate, which may be used to determine the frostbite sensitivity of a new sample.

• Smart Structures and Systems
• /
• v.16 no.4
• /
• pp.683-699
• /
• 2015

Time Domain Reflectometry (TDR) has been extensively applied for various laboratory and field studies. Numerous different TDR probes are currently available for measuring soil moisture content and detecting interfaces (i.e., due to landslides or structural failure). This paper describes the development of an innovative spiral-shaped TDR probe that features much higher sensitivity and resolution in detecting interfaces than existing ones. Finite element method (FEM) simulations were conducted to assist the optimization of sensor design. The influence of factors such as wire interval spacing and wire diameter on the sensitivity of the spiral TDR probe were analyzed. A spiral TDR probe was fabricated based on the results of computer-assisted design. A laboratory experimental program was implemented to evaluate its performance. The results show that the spiral TDR sensor featured excellent performance in accurately detecting thin water level variations with high resolution, to the thickness as small as 0.06 cm. Compared with conventional straight TDR probe, the spiral TDR probe has 8 times the resolution in detecting the water level changes. It also achieved 3 times the sensitivity of straight TDR probe.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.5
• /
• pp.99-107
• /
• 2003

Moisture flow and heat flow within pavement systems have been recognized as coupled processes with complex interactions between them. The distribution of moisture and temperature within pavement due to the moisture flow and heat flow varies not only seasonally but also vertically and horizontally. This paper presents an analysis model by the finite element method for the two-dimensional coupled moisture and heat flow in unsaturated soils. To test the model the analysis result by the model is compared with the analysis result by the software, GEO-SLOPE developed by GEO-SLOPE International Ltd. in Alberta, Canada. And a sensitivity analysis using ASTM method is performed to identify how model inputs affect the modeling analysis.

• Journal of Mechanical Science and Technology
• /
• v.17 no.1
• /
• pp.57-63
• /
• 2003

An eigenvalue design sensitivity formulation of a general nonsymmetric-matrix rotor-bearing system is devised. using the DDM (direct differential method). Then, investigations on the design sensitivities of critical speeds are carried out for an APU turbogenerator with a spline shaft connection. Results show that the dependence of the rate of change of the critical speed on the stiffness changes of bearing models of spline shaft connection points is negligible, and thereby their modeling uncertainty does not present any problem. And the passing critical speeds up to the 4th critical speed are not sensitive to the design stiffness coefficients of four main bearings. Further, the dependence of the rate of change of the critical speed on the shaft-element length changes shows quantitatively that the spline shaft has some limited influence on the 4th critical speed but no influence on the 1st to 3rd critical speeds. With no adverse effect from the spline shaft, the APU system achieves a critical speed separation margin of more than 40% at a rated speed of 60,000 rpm.

• Journal of the Korean Institute of Navigation
• /
• v.25 no.1
• /
• pp.45-52
• /
• 2001

The purpose of this study is the optimum modification of dynamic characteristics of stiffened plate structure. In the method of the optimization, finite element method(FEM), sensitivity analysis and optimum structural modification method are used. To begin with, using FEM, the dynamic characteristics of stiffened plate structure is analyzed. Next, rate of change of dynamic characteristics by the change of design variable is calculated using the sensitivity analysis. Then, amount of change of design variable is calculated using this sensitivity value and optimum structural modification method. The change of natural frequency is made to be an objective function. Thickness of plate and cross section moment become a design variable. It is shown that the results are effective in the optimum modification for dynamic characteristics of the stiffened plate structure.

• Journal of Sensor Science and Technology
• /
• v.7 no.1
• /
• pp.1-8
• /
• 1998

We have simulated the operating characteristics of the magnetotransistor(MAGFET) by the finite element method and suggested the optimum design conditions to get a maximum sensitivity, The magnetotransistor has been fabricated by CMOS standard processing according to the suggested design conditions and investigated its electromagnetic characteristics. The sensitivity of the magnetotransistor depends on the ratio of width(W) to length(L) of active area rather than its size, and has a maximum when W/L = 1. The relative sensitivity of a fabricated magnetotransistor was 2.53 %/T.

• Smart Structures and Systems
• /
• v.22 no.4
• /
• pp.441-457
• /
• 2018

Characteristic parameter values of seismic isolators deviate from their nominal design values due to uncertainties and/or errors in their material properties and element dimensions, etc. Deviations may increase over service life due to environmental effects and service conditions. For accurate evaluation of the seismic safety level, all such effects, which would result in deviations in the structural response, need to be taken into account. In this study, the sensitivity of the probability of failure of the structures equipped with nonlinear base isolation systems to the uncertainties in various isolation system characteristic parameters is investigated in terms of various isolation system and superstructure response parameters in the context of a realistic three-dimensional base-isolated building model via Monte Carlo Simulations. The inherent record-to-record variability nature of the earthquake ground motions is also taken into account by carrying out analyses for a large number of ground motion records which are classified as those with and without forward-directivity effects. Two levels of nominal isolation periods each with three different levels of uncertainty are considered. Comparative plots of cumulative distribution functions and related statistical evaluation presented here portray the potential extent of the deviation of the structural response parameters resulting from the uncertainties and the uncertainty levels considered, which is expected to be useful for practicing engineers in evaluating isolator test results for their projects.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.2
• /
• pp.236-247
• /
• 1992

Optimization has been developed to minimize the cost function while satisfying constraints. Nonlinear Programming method is used as a tool for the optimization. Usually, cost and constraint function calculations are required in the engineering applications, but those calculations are extremely expensive. Especially, the function and sensitivity analyses cause a bottleneck in structural optimization which utilizes the Finite Element Method. Also, when the functions are quite noisy, the informations do not carry out proper role in the optimization process. An algorithm called "Second-order Approximation Method" has been proposed to overcome the difficulties recently. The cost and constraint functions are approximated by the second-order Taylor series expansion on a nominal points in the algorithm. An optimal design problem is defined with the approximated functions and the approximated problem is solved by a nonlinear programming numerical algorithm. The solution is included in a candidate point set which is evaluated for a new nominal point. Since the functions are approximated only by the function values, sensitivity informations are not needed. One-dimensional line search is unnecessary due to the fact that the nonlinear algorithm handles the approximated functions. In this research, the method is analyzed and the performance is evaluated. Several mathematical problems are created and some standard engineering problems are selected for the evaluation. Through numerical results, applicabilities of the algorithm to large scale and complex problems are presented.presented.